掺杂Sc和Sb的Mg2Si基热电材料的电性能研究

采用机械合金化-电场激活压力辅助合成(MA-FAPAS)技术,快速合成Sc,Sb掺杂的Mg2Si基热电材料,并对其进行电性能的测试与分析。结果表明:掺杂摩尔分数为0.47%Sb的Mg2Si试样在测试温度范围内,电导率和Seebeck系数均优于未掺杂试样,其平均电功率因子约为后者的2.2～2.3倍;电导率比采用熔融-热压法制备的同类试样有所提高;在低温阶段,掺杂摩尔分数为0.43%Sc的Mg2Si试样Seebeck系数约为307 K,达未掺杂试样的2.03倍;电功率因子在温度低于550 K时高于未掺杂试样,最大值与Sb掺杂试样相当。     

数字炮控系统中旋转变压器信号转换电路的设计

将旋转变压器(旋变)的高可靠性和微处理器的快速数据处理能力相结合来实现旋变的轴角编码,并应用于数字交流全电炮控系统中提供速度和位置反馈,提高了系统的可靠性和低速性能.该文重点介绍了旋变信号的处理电路及其与DSP的硬件接口.     

Enhanced Ionic/Electronic Transport in Nano‐TiO2/Sheared CNT Composite Electrode for Na+ Insertion‐based Hybrid Ion‐Capacitors

Ion‐insertion capacitors show promise to bridge the gap between supercapacitors of high power densities and batteries of high energy densities. While research efforts have primarily focused on Li⁺‐based capacitors (LICs), Na⁺‐based capacitors (SICs) are theoretically cheaper and more sustainable. Owing to the larger size of Na⁺ compared to Li⁺, finding high‐rate anode materials for SICs has been challenging. Herein, an SIC anode architecture is reported consisting of TiO₂ nanoparticles anchored on a sheared‐carbon nanotubes backbone (TiO₂/SCNT). The SCNT architecture provides advantages over other carbon architectures commonly used, such as reduced graphene oxide and CNT. In a half‐cell, the TiO₂/SCNT electrode shows a capacity of 267 mAh g^?1 at a 1 C charge/discharge rate and a capacity of 136 mAh g^?1 at 10 C while maintaining 87% of initial capacity over 1000 cycles. When combined with activated carbon (AC) in a full cell, an energy density and power density of 54.9 Wh kg^?1 and 1410 W kg^?1, respectively, are achieved while retaining a 90% capacity retention over 5000 cycles. The favorable rate capability, energy and power density, and durability of the electrode is attributed to the enhanced electronic and Na⁺ conductivity of the TiO₂/SCNT architecture.     

Optimal design of APD biasing circuit

This paper proposes a control method for avalanche photodiode(APD) reverse bias with temperature compensation and load resistance compensation. The influence of background light and load resistance on APD detection circuit is analyzed in detail. A theoretical model of temperature compensation and load resistance compensation is established,which is used for APD biasing circuit designing. It is predicted that this control method is especially suitable for LD laser range finder used on vehicles. Experimental results confirm that the design proposed in this paper can considerablely improve the performance of range finder.     

P2P流量优化技术及标准化进展

文章综述了P2P流量优化的技术路线（P2P应用层优化和层间协同机制）,介绍了目前具有代表性的一些解决方案,如应用层优化方案IDMaps、Vivaldi、iPlan、OnO,层间协作方案P4P、Oracle、PPM和DDP,以及国内外标准化组织标准推进情况。     

冷冲高硬度材料模具的失效分析与选材

用WC-Co型硬质合金和高合金钢以不同的匹配方式制作冷冲模具,对高硬度材料2Cr13不锈钢进行冲裁,发现以高合金钢制作的模具寿命远高于硬质合金制作的模具。其失效方式及所占比例表明,硬质合金主要以掉渣和崩刃为主,而高合金钢以正常磨损为主。分析可知,由于剧烈磨损而引起WC-Co型硬质合金Co的缺失,破坏了WC骨架,最终导致模具局部韧性不足而掉渣;而高合金钢韧性相对较好,延长了使用寿命,但同时由于热加工工艺的不适当导致碳化物不均或硬度不稳定而未充分发挥材料的潜能,对提高高合金钢的使用寿命给出了改进方案。     

基于NS2的Ad hoc网络仿真研究

Ad hoc网络是一种不需要任何通信基础设施的典型的自组织网络,运用ns2对Ad hoc网络尤其是对其路由协议的研究成了广大网络研究者的一种重要手段.本文首先介绍了Ad hoc网络和ns2.然后给出了在ns2下进行Ad hoc网络仿真的步骤和方法.最后给出了AODV路由协议的仿真实例,结果说明了运用ns2研究Ad hoc网络的可行性和有效性.     

基于MAXWELL2D静磁场分析的特种电机教学

特种电机应用越来越广泛,已成为“电机学”教学的重要内容,其结构和磁场分布不同于传统同步电机,是“电机学”教学的难点之一。本文以永磁电机为例,探讨了MAXWELL2D建模实现电机旋转结构动画显示的方法,并利用MAXWELL2D对永磁电机进行静磁场有限元分析,直观呈现电机内磁场分布特点,便于学生理解和接受特种电机的结构和原理。本文方法对于其他特种电机的教学具有参考价值。     

Growth and dielectric properties of Ta_2O_5 single crystals grown by laser heated pedestal growth technique

Ta2O5 single crystals have been grown by the laser heated pedestal growth (LHPG) technique up to several centimeters length with diameter of 1.1 mm. The crystal, characterized by X-ray diffraction, dielectric measurement, and thermal expansion analysis, has Htri-Ta2O5 symmetry. Dielectric permittivity, loss tangent along [001] and [110] direction were investigated over the temperature range from -80 ℃ to 100 ℃. Large dielectric anisotropy in Ta2O5 single crystal was observed. At room temperature, the dielectric permittivities (1 MHz) along [001] and [110] are 33.2 and 231.9, respectively. The reason of dielectric enhancement in Ta2O5 crystal grown by LHPG was also discussed.     

EVALUATION OF MALTING QUALITY IN A BARLEY BREEDING PROGRAMME USE OF α-AMYLASE AND β-GLUCAN LEVLES IN MALT AS PRESELECTION TOOLS

Analysis according to the EBC protocol, immunological determination of a α-amylase and estimation of malt β-glucan using the Calcofluor-FIA method, were used to screen 327 barley breeding lines for malting quality. The results obtained with the α-amylase and β-glucan methods are highly correlated to the important malt quality paramters: extract yield and β-glucan content in the wort. It is recommended that either of the two methods, which are simple to perform are used as prescreening tools in breeding programmes for malting barley.