Evaluating the 1931 CIE color‐matching functions

The use of colorimetry within industry has grown extensively in the last few decades. Central to many of today's instruments is the CIE system, established in 1931. Many have questioned the validity of the assumptions made by Wright¹ and Guild,² some suggesting that the 1931 color‐matching functions are not the best representation of the human visual system's cone responses. A computational analysis was performed using metameric data to evaluate the CIE 1931 color‐matching functions as compared to with other responsivity functions. The underlying assumption was that an optimal set of responsivity functions would yield minimal color‐difference error between pairs of visually matched metamers. The difference of average color differences found in the six chosen sets of responsivity functions was small. The CIE 1931 2° color‐matching functions on average yielded the largest color difference, 4.56 ΔE. The best performance came from the CIE 1964 10° color‐matching functions, which yielded an average color difference of 4.02 ΔE. An optimization was then performed to derive a new set of color‐matching functions that were visually matched using metameric pairs of spectral data. If all pairs were to be optimized to globally minimize the average color difference, it is expected that this would produce an optimal set of responsivity functions. The optimum solution was to use a weighted combination of each set of responsivity functions. The optimized set, called the Shaw and Fairchild responsivity functions, was able to reduce the average color difference to 3.92 ΔE. In the final part of this study a computer‐based simulation of the color differences between the sets of responsivity functions was built. This simulation allowed a user to load a spectral radiance or a spectral reflectance data file and display the tristimulus match predicted by each of the seven sets of responsivity functions. © 2002 Wiley Periodicals, Inc. Col Res Appl, 27, 316–329, 2002; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.10077     

Decentralized weighted control for a class of large‐scale systems with multi‐modes

In this paper, the control synthesis problem for a class of large‐scale systems with multi‐modes that are called large‐scale switched systems is addressed. By introducing the concept of decentralized switching signal and the relevant decentralized average dwell time, the asymptotic stability and weighted ?₂ gain performance are investigated. It should be noted that the decentralized switching covers general switching cases for large‐scale switched systems, namely, it admits both time‐dependent switching signal and arbitrary switching signal blended in the decentralized switching. Then, on the basis of the analysis results, the decentralized weighted control scheme including state feedback controller gains and switching signals is studied. Several design algorithms are proposed to meet different controller design problems. Finally, numerical examples are provided to illustrate theoretical findings within this paper. Copyright © 2013 John Wiley & Sons, Ltd.     

Bulk and Interphase Effects in Aged Structural Joints

Although structural adhesives are becoming widespread in numerous applications, one important limitation at present is the long term behaviour of bonded assemblies under conditions of high humidity, especially at elevated temperatures. This study presents a comparison between bulk properties of a structural epoxy resin and its behaviour in a torsional joint consisting of a hollowed-out cylinder bonded to a plate—both substrates being in stainless steel. Exposure to ca. 100% relative humidity at 70°C leads to modification of the bulk properties of the polymer, notably reduction of its elastic modulus. Although this may explain some differences in behaviour of the torsional joint, premature failure is attributed to weaknesses in the interphase zone.

Auger Electron Spectroscopy (AES) has been employed to investigate both unbonded steel surfaces and fracture zones. Although prolonged exposure to water leads to a more extensive degree of (apparently) adhesive failure at the interface polymer/metal, AES has shown the presence of non-negligible quantities of carbon, attributed to residual polymer. Failure would seem to occur, at least partly, in a weak interphase of the polymer, near, but not at, the interface.

Various possible causes are evoked. For dry failure, residual polymer may be due to the topography of the metal surface and/or local modification of the adhesive during cure. In the case of aged joints, in addition there are potential effects due to swelling and differential stresses, secondary bond failure and molecular chain scission within the polymer, all provoked by the presence of water.     

Shape‐memory polyurethane/multiwalled carbon nanotube fibers

Shape‐memory polyurethane/multiwalled carbon nanotube (SMP–MWNT) composites with various multiwalled carbon nanotube (MWNT) contents were synthesized, and the corresponding SMP–MWNT fibers were prepared by melt spinning. The influence of the MWNT content on the spinnability, fracture morphology, thermal and mechanical properties, and shape‐memory behavior of the shape‐memory polymer was studied. The spinning ability of SMP–MWNTs decreased significantly with increasing MWNT content. When the MWNT content reached 8.0 wt %, the fibers could not be produced because of the poor rheological properties of the composites. The melt‐blending, extrusion, and melt‐spinning processes for the shape‐memory fiber (SMF), particularly at low MWNT contents, caused the nanotubes to distribute homogeneously and preferentially align along the drawing direction of the SMF. The crystallization in the SMF was promoted at low MWNT contents because it acted as a nucleation agent. At high MWNT contents, however, the crystallization was hindered because the movement of the polyurethane chains was restricted. The homogeneously distributed and aligned MWNTs preserved the SMF with high tenacity and initial modulus. The recovery ratio and recovery force were also improved because the MWNTs helped to store the internal elastic energy during stretching and fixing. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Characterization of konjac glucomannan–quaternized poly(4‐vinyl‐N‐butyl) pyridine blend films and their preservation effect

Novel polymer blends were prepared from a mixture of 2 wt % konjac glucomannan and 4 wt % quaternized poly(4‐vinyl‐N‐butyl) pyridine (QPVP) in aqueous solution and dried at room temperature for 72 h. Their structure and properties were studied by infrared, wide‐angle X‐ray diffraction, scanning electron microscopy, thermogravimetric analysis, and differential scanning calorimetry. Thermal stability in the dry state was reduced with increasing content of QPVP. Compared with QPVP film, the tensile strength of the films was improved in the dry state. The maximum value of 12.74% tensile break elongation was reached when the content of QPVP was 30%. Structural analysis indicated that clear phase separation was observed when the content of QPVP was only 50%. Results from the filmcoating preservation experiments with lychee showed that this blend film had water‐holding ability. The fruit weight loss rate and rot rate both decreased in various degrees. The potential uses of these novel polymer films could be as preservative films. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1868–1875, 2004     

Factors influencing magnetic polymer microspheres prepared by dispersion polymerization

Magnetic iron oxide (Fe₃O₄) was prepared by a coprecipitation method. Core–shell composite magnetic polymer microspheres with carboxyl groups were synthesized by the dispersion polymerization of styrene and acrylic acid in the presence of magnetic oxide, and dibenzoyl peroxide was used as an initiator. The synthesized magnetic polymer microspheres were characterized with X‐ray diffraction, transmission electron microscopy, scanning electron microscopy, Fourier transform infrared spectroscopy, and so forth. The results indicated that the product was single‐phase Fe₃O₄, and its average size was about 10 nm. The configuration of the microspheres, which contained carboxyl groups, was spherical, and the average size was about 2 μm. The results of vibrating sample magnetometry tests showed that the magnetic powders produced by different surfactants had different saturation magnetizations. When poly(ethylene glycol) with a weight‐average molecular weight of 4000 was used as a surfactant, the saturation magnetization of the samples reached 69.2 emu/g. The factors that affected the shape, magnetism, size, and distribution of the microspheres were also studied. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Ferroelectric liquid crystals: Excellent tool for modern displays and photonics

The ferroelectric liquid crystals, because of their fast electro‐optical response, are one of the most important classes of liquid crystals. Here, in this review, we have summarized the different electro‐optical modes for ferroelectric liquid crystals. Clark–Lagerwall effect (surface stabilized ferroelectric liquid crystal), deformed helix ferroelectric (DHF) effect, electrically suppressed helix (ESH) mode, DHF orientational Kerr effect, and ESH diffraction modes have been discussed. All of the crucial features, that is, optics, electro‐optics, dynamics, and their dependence on material parameters, operational regime, and applications, have been reviewed.     

On input‐to‐state stability‐based design for leader/follower formation control with measurement delays

This paper addresses the design of low‐level controllers for leader–follower formations of nonholonomic vehicles in the presence of bounded measurement delays. The concept of input‐to‐state stability is extended to encompass the effect of bounded delays and restrictions on the input. A method is proposed to integrate a Smith predictor in a backstepping design on the basis of nested saturations and nonlinear small‐gain assignment, which allows for time delays in the feedback loop. Robustness analysis under uncertain bounded time delays is provided, and design tradeoffs resulting from the use of bounded controls are discussed. Illustrative simulations are shown to validate the design and robustness analysis in the context of a simple leader–follower trailing control problem. Copyright © 2012 John Wiley & Sons, Ltd.     

Genetic algorithm‐based neural‐network modeling approach applied to AlGaN/GaN devices

An accurate equivalent circuit large‐signal model (ECLSM) for AlGaN‐GaN high electron mobility transistor (HEMT) is presented. The model is derived from a distributed small‐signal model that efficiently describes the physics of the device. A genetic neural‐network‐based model for the gate and drain currents and charges is presented along with its parameters extraction procedure. This model is embedded in the ECLSM, which is then implemented in CAD software and validated by pulsed and continuous large‐signal measurements of on‐wafer 8 × 125‐μm GaN on SiC substrate HEMT. Pulsed IV simulations show that the model can efficiently describe the bias dependency of trapping and self‐heating effects. Single‐ and two‐tone simulation results show that the model can accurately predict the output power and its harmonics and the associated intermodulation distortion (IMD) under different input‐power and bias conditions. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Spatial and functional relationships between air conduits and blood capillaries in the pulmonary gas exchange tissue of adult and developing chickens

The documented data regarding the three-dimensional structure of the air capillaries (ACs), the ultimate sites of gas exchange in the avian lung is contradictory. Further, the mode of gas exchange, described as cross-current has not been clearly elucidated. We studied the temporal and spatial arrangement of the terminal air conduits of the chicken lung and their relationship with the blood capillaries (BCs) in embryos as well as the definitive architecture in adults. Several visualization techniques that included corrosion casting, light microscopy as well as scanning and transmission electron microscopy were used. Two to six infundibulae extend from each atrium and give rise to numerous ACs that spread centrifugally. Majority of the ACs are tubular structures that give off branches, which anastomose with their neighboring cognates. Some ACs have globular shapes and a few are blind-ending tapering tubes. During inauguration, the luminal aspects of the ACs are characterized by numerous microvillus-like microplicae, which are formed during the complex processes of cell attenuation and canalization of the ACs. The parabronchial exchange BCs, initially inaugurated as disorganized meshworks, are reoriented via pillar formation to lie predominantly orthogonal to the long axes of the ACs. The remodeling of the retiform meshworks by intussusceptive angiogenesis essentially accomplishes a cross-current system at the gas exchange interface in the adults, where BCs form ring-like patterns around the ACs, thus establishing a cross-current system. Our findings clarify the mode of gas exchange in the parabronchial mantle and illuminate the basis for the functional efficiency of the avian lung.