Polyaniline as an electrode material for magnesium reserve battery

The results of the investigation on the use of polyaniline (PANI) as a cathode material in a battery configuration, having magnesium as anode and a neutral aqueous solution of one of the magnesium salts such as perchlorate, chloride and bromide as an electrolyte, are presented. This system shows a open circuit voltage in the range 1.6-1.8 V. The study indicates that the capacity of the system largely depends upon the anion present in the electrolyte.     

Determination of the rate-determining step of the oxygen reduction reaction of La0.8Sr0.2MnO3(LSM)- 8mol% yttria-stabilized zirconia(YSZ): Composition and microstructure

In this study, LSM-YSZ composite cathodes were analyzed by changing the firing temperature, composition, and operating temperature to determine the contribution of each step of the oxygen reduction reaction (ORR). The overall resistance of the cathode reaction was characterized by fitting the AC impedance spectra with an equivalent circuit model. It was found that initial reactions of ORR (dissociative adsorption) are the main rate-determining step (RDS) regardless of operating or sintering temperature, while reactions on LSM surface become the main RDS when the ratio of LSM catalysts has a relatively small proportion. The [LSM-YSZ]_5:5 cathode fired at 1100 °C showed the best microstructure and lowest resistance in the ORR at an operating temperature of 700 °C (R_HF: 0.18 Ωcm², R_MF: 0.20 Ω cm², R_LF: 0.25 Ωcm², R_cathode: 1.14 Ωcm²). This demonstrates the potential use of LSM-YSZ cathodes for IT/LT-SOFC without the use of expensive materials, such as LSCF and BSCF.     

Layered NdBaCo2−xNixO5+δ perovskite oxides as cathodes for intermediate temperature solid oxide fuel cells

The effect of Ni substitution on the crystal chemistry, thermal and electrochemical properties, and catalytic activity for oxygen reduction reaction of the layered NdBaCo_2−xNi_xO_5+δ perovskite oxides has been investigated for 0 ≤ x ≤ 0.6. The oxygen content (5 + δ) and oxidation state of the (Co, Ni) ions in the air-synthesized NdBaCo_2−xNi_xO_5+δ samples decrease with increasing Ni content, accompanied by a structural transition from tetragonal (0 ≤ x ≤ 0.4) to orthorhombic (x = 0.6). Similarly, the thermal expansion coefficient (TEC) and electrical conductivity also decrease with increasing Ni content. The x = 0.2 and 0.4 samples exhibit slightly improved performance as cathodes in single cell solid oxide fuel cell (SOFC) compared to the x = 0 sample, which is in accordance with the ac-impedance data. Among the samples studied, the x = 0.4 sample exhibits a combination of low thermal expansion and high catalytic activity for the oxygen reduction reaction in SOFC.     

Review on electrode–electrolyte solution interactions,related to cathode materials for Li-ion batteries

In this paper we review some critical aspects related to interactions between cathode materials and electrolyte solutions in lithium-ion batteries. Previous results are briefly summarized, together with the presentation of new results. This review deals with the basic anodic stability of commonly-used electrolyte solutions for Li-ion batteries (mostly based on alkyl carbonate solvents). We discuss herein the surface chemistry of the following cathode materials: LiCoO₂, V₂O₅, LiMn₂O₄, LiMn_1.5Ni_0.5O₄, LiMn_0.5Ni_0.5O₂, and LiFePO₄. The methods applied included solution studies by ICP, Raman, X-ray photoelectron and FTIR spectroscopies, and electron microscopy, all in conjunction with electrochemical techniques. General phenomena are the possible dissolution of transition metal ions from these materials, which leads to changes in the active mass and a retardation in the electrode kinetics due to the formation of blocking surface films. These phenomena are significant mostly at elevated temperatures and in electrolyte solutions containing acidic species. Water-contaminated LiPF₆ solutions can reach a high concentration of acidic species (e.g., HF), which is detrimental to the performance of materials such as LiCoO₂ and LiFePO₄. Both LiMn_1.5Ni_0.5O₄ and LiMn_0.5Ni_0.5O₂, even when used as nanomaterials, show a high stability in commonly-used electrolyte solutions at high temperatures. This stability is attributed to unique surface chemistry that is correlated to the presence of Ni ions in the lattice.     

Solid oxide fuel cell cathodes prepared by infiltration of LaNi0.6Fe0.4O3 and La0.91Sr0.09Ni0.6Fe0.4O3 in porous yttria-stabilized zirconia

SOFC composite electrodes of yttria-stabilized zirconia (YSZ) and either LaNi_0.6Fe_0.4O₃ (LNF) or La_0.91Sr_0.09Ni_0.6Fe_0.4O₃ (LSNF) were prepared by infiltration to a loading of 40 wt% of the perovskite into porous YSZ using aqueous solutions of the nitrate salts. XRD measurements indicated that the perovskite structures were formed following calcination at 850 °C, at which temperature the LNF and LSNF form small particles that coat the YSZ pores. Heating to 1100 °C causes the particles to form a dense film over the YSZ but caused no solid-state reaction. Calcination of an LNF-YSZ composite to 1200 °C led to an expansion of the LNF lattice, suggesting introduction of Zr(IV) into the perovskite; further heating to 1300 °C caused the formation of La₂Zr₂O₇. For 850 °C calcination, the electrode performance of both LNF-YSZ and LSNF-YSZ composites was similar to that reported for composites of YSZ and La_0.8Sr_0.2FeO₃ (LSF), with a current-independent impedance of approximately 0.1 Ω cm² at 700 °C in air. For 1100 °C calcination, both LNF-YSZ and LSNF-YSZ composites exhibited impedances that decreased strongly under both anodic and cathodic polarization. The implications of these results for preparing electrodes based on LNF and LSNF are discussed.     

Electrochemical properties of bare and Ta-substituted Nb2O5 nanostructures

In this work, bare and Ta-substituted Nb₂O₅ nanofibers are prepared by electrospinning followed by sintering at temperatures in the 800–1100 °C range for 1 h in air. Obtained bare and Ta-substituted Nb₂O₅ polymorphs are characterized by X-ray diffraction, scanning electron microscopy, density measurement, and Brunauer, Emmett and Teller surface area. Electrochemical properties are evaluated by cyclic voltammetry and galvanostatic techniques. Cycling performance of Nb₂O₅ structures prepared at temperature 800 °C, 900 °C, and 1100 °C shows following discharge capacity at the end of 10th cycle: 123, 140, and 164 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹ (1.5 C rate). Heat treated composite electrode based on M-Nb₂O₅ (1100 °C) in argon atmosphere at 220 °C, shows an improved discharge capacity of 192 (±3) mAh g⁻¹ at the end of 10th cycle. The discharge capacity of Ta-substituted Nb₂O₅ prepared at 900 °C and 1100 °C showed a reversible capacity of 150, 202 (±3) mAh g⁻¹, respectively, in the voltage range 1.2–3.0 V and at current rate of 150 mA g⁻¹. Anodic electrochemical properties of M-Nb₂O₅ deliver a reversible capacity of 382 (±5) mAh g⁻¹ at the end of 25th cycle and Ta-substituted Nb₂O₅ prepared at 900 °C, 1000 °C and 1100 °C shows a reversible capacity of 205, 130 and 200 (±3) mAh g⁻¹ (at 25th cycle) in the range, 0.005–2.6 V, at current rate of 100 mA g⁻¹.     

Synthesis of compounds, Li(MMn11/6)O4 (M = Mn1/6, Co1/6, (Co1/12Cr1/12), (Co1/12Al1/12), (Cr1/12Al1/12)) by polymer precursor method and its electrochemical performance for lithium-ion batteries

The compounds, Li(MMn_11/6)O₄ (M = Mn_1/6, Co_1/6, (Co_1/12Cr_1/12), (Co_1/12Al_1/12), (Cr_1/12Al_1/12)) are synthesised by the polymer precursor method. The structure and the morphology of the compounds are studied by the Rietveld refined X-ray diffraction (XRD), and transmission electron microscopy (TEM) techniques, respectively. Density and the Brunauer, Emmet and Teller surface area (BET) of the compounds are also studied. The cobalt doped compound, Li(Co_1/6Mn_11/6)O₄ is found to be nanosized particles in the range of 60-100 nm, when compared to the other compounds in our present study. The oxidation state and the local structure of the compounds are analysed by the X-ray absorption spectroscopy (XAS) technique. Cyclic voltammetry (CV) and the galvanostatic charge-discharge cycling (30 mA g⁻¹) studies are made in the voltage range of 3.5-4.3 V at room temperature for all the compounds under study. The bare and (Co_1/6), and (Co_1/12Cr_1/12) substituted spinels are cycled at high current rates of 1, 2 and 5C (assuming 1C∼120 mA g⁻¹). Cycling results of Co-substituted spinels show better and long-term capacity retention at all the current rates. At the end of the second cycle, Li(Co_1/6Mn_11/6)O₄ compound delivers a discharge capacity value of 100 (±3) and 87 (±3) mAh g⁻¹ for the current rate of 2 and 5C, respectively. An excellent capacity retention value of 94% is observed at the end of the 1000 cycles for both 2 and 5C rates.     

Manganese-rich SmBaCo2−x−yMnxMgyO5+δ (x = 0.5, 1, 1.5 and y = 0.05, 0.1) with stable structure and low thermal expansion coefficient as cathode materials for IT-SOFCs

SmBaCo_2−x−yMn_xMg_yO_5+δ (x = 0.5, 1, 1.5 and y = 0.05, 0.1) samples are synthesized by sol-gel method. The influence of different substitution of Mn and Mg for Co on crystal structures, thermal expansion coefficient (TEC), electrical conductivities and electrochemical performances have been investigated. The generation of the secondary phase BaMnO₃ is suppressed with Mg²⁺ increasing. Demonstrated by temperature-dependent X-ray diffraction from 25 °C to 700 °C, the structure of SmBaCo_0.4Mn_1.5Mg_0.1O_5+δ in high temperature is stable. The TEC of SmBaCo_1.45Mn_0.5Mg_0.05O_5+δ, SmBaCo_0.95MnMg_0.05O_5+δ, SmBaCo_0.45Mn_1.5Mg_0.05O_5+δ and SmBaCo_0.4Mn_1.5Mg_0.1O_5+δ are 15.77 × 10⁻⁶ K⁻¹, 16.20 × 10⁻⁶ K⁻¹, 12.19 × 10⁻⁶ K⁻¹ and 12.58 × 10⁻⁶ K⁻¹, respectively, which are much lower than those of cobalt-based layered perovskites and more compatible with the thermal expansion of SDC electrolyte. Although the electrochemical performances of SmBaCo_2−x−yMn_xMg_yO_5+δ (x = 0.5, 1, 1.5 and y = 0.05, 0.1) decrease slightly with Mn increasing, the polarization resistances of the SmBaCo_1.45Mn_0.5Mg_0.05O_5+δ and SmBaCo_0.4Mn_1.5Mg_0.1O_5+δ are 0.17 Ω cm² and 0.30 Ω cm² at 800 °C, respectively, which can meet the electrochemical performance requirements of cathode materials. Among the samples, the SmBaCo_1.45Mn_0.5Mg_0.05O_5+δ and SmBaCo_0.4Mn_1.5Mg_0.1O_5+δ show better tradeoff properties between TEC and electrochemical performance as cathode materials for IT-SOFCs.