Schubspannungsbomben in Faserverbunden

Shear Bombs in Fibre Composites Despite an optimum external shape non‐load adapted internal fibre orientation can lead to the formation of shear cracks where crossing tension‐compression principal stress trajectories create localized shear peaks. Trees are subject to those failure because they cannot re‐arrange their fibres after wood formation. Bones can adjust their micro‐structure to changing load conditions and in this way can better control shear failure. The engineer working with fibre composites should be alert to avoid fibre arrangements not following the force flow. Localized shear zones may also form near notches similar to normal notch stresses, however they are not always situated at the contour line of the notch.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

Ischemia‐reperfusion injury. A phenomenon,that also occurs in the bone

Ischemia‐reperfusion injury of the bone occurs due to traumatic and non‐traumatic alterations affecting blood supply to the bone. It is likely to occur also upon insertion of an implant. Ischemia‐reperfusion injury of the bone has been studied by interruption of blood supply in situ, in limb replantation/transplantation models, in revascularized bone grafts and non‐vascularized bone fragments, as well as in isolated cultured cells. All cells of the bone are affected, including osteoblasts, osteocytes, osteoclasts, chondrocytes, and bone marrow cells. Critical ischemia times for induction of bone cell death, either in the ischemic period or following reperfusion, are in the range of 3 to 7 h. These critical ischemia times are significantly increased by decreasing the temperature from 37 °C to 0–4 °C. Anoxia is the most likely trigger of cell injury in the ischemic phase. In the reperfusion phase, reactive oxygen species are decisively involved in the injurious process. In general, however, the available information on the mechanism of ischemia‐reperfusion injury of the bone is relatively sparse. On the other hand, there are clear similarities to the mechanisms of ischemia‐reperfusion injury known from other organs, and there is a clear potential for protection against ischemia‐reperfusion injury of the bone.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

Cr12MoV钢冷挤压成形模强化工艺的研究

针对Crl2MoV钢冷挤压成形模热处理存在的质量问题，对加热温度和方式进行了大量的试验研究，在此基础上，提出了改进的快速加热工艺。结果表明，经该工艺处理后，模具使用寿命得到显提高。     

The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.     

包装发展需要环境友好包装材料

环境友好包装材料是一类具有环境意识特征的概念.环境友好包装材料依据“4R 1D“原则,注重包装材料与环境的协调性,指导包装材料的研发,一是有利于保护自然资源;二是对生态环境损害最少化.运用环境友好包装材料的概念,实现包装的可持续发展.     

High‐Tech‐Cellulose‐Funktionspolymere nach dem ALCERU®‐Verfahren

Functional High‐Tech‐Cellulose materials by the ALCERU® process Cellulose is one of the eldest materials of mankind. While the use of cellulose in former times was focused on application as a more construction or as a more textile material at present time the application profile turns to a more functional material using the ALCERU® process. Shaping of pure cellulose dissolution in NMMNO permits the manufacturing of materials for upholstery, filtration or biodegradable film strips having an uniform cross section. Fibreds, which can be applied in several packaging materials, are available using different techniques for regeneration cellulose. A great field of innovative functional cellulose materials is opened up by addition of several functional additives to cellulose dissolution. In this way piezo‐electrical conductive cellulose fibres (PZT) or high‐temperature filtration membranes are to be generated if one adds special types of ceramic powders. Above all PZT green fibres are applied in more recent uses as sensors or actuators. Electrically conductive cellulose fibres or filaments, which can be also used in the textile chain, can be prepared adding conductive carbon black to a cellulose dope on the same way, too. Cellulose material having adapted conductivity to different application is available by adding an exact defined amount of carbon black to cellulose dissolution. Finally cellulose beads can be manufactured by means of varied shaping technique. The beads are showing variable particle sizes and narrow pore size distribution. These properties open up very interesting application in the field of human blood purification or chromatography.