Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

10kV配电室操作控制电源电压下降的解决措施

本提出了10kV配电室操作电压下降的现场解决方案。     

一种基于判决反馈的OFDM系统载波频率跟踪算法

研究了多径信道下OFDM系统的一种新的载波频率跟踪算法，这种算法以判决反馈和接收端的时域信号重构为基础。推导了估计结果的精确解，比较了使用原估计结果和新的估计结果进行频偏补偿时系统跟踪性能的不同。通过对算法的仔细分析，发现除了通常的加性噪声外，信道估计误差、子载波数目和子载波的调制方式也影响频偏的估计结果和跟踪范围，而且子载波的数目和调制方式是决定性的因素。这种频率跟踪方法的优点是即使在很低的信噪比下仍然能获得高的跟踪精度，且实现相对简单。     

Dynamic vulcanisation of EPDM/PE-based thermoplastic vulcanisates studied along the extruder axis

Simple blending and dynamic vulcanisation of EPDM/PE blends using the resol/SnCl₂ system was studied in an extruder using a series of sampling devices. The melting of the PE pellets occurs just in front of and in the first kneading zone. Upon complete melting of the PE phase, the EPDM/PE blends reach very quickly their final morphology. Crosslinking of the EPDM phase to high levels occurs already when the PE phase is not yet fully molten. The higher the EPDM content, the higher the viscous dissipation, the higher the melt temperature and, consequently, the higher the crosslinking rate. For the EPDM/PE (50/50; w/w) TPV a transition from continuous via co-continuous to fully dispersed EPDM is observed, which is driven by crosslinking. Although the degree of crosslinking of the EPDM rubber is very high, this does not prevent phase inversion of the blend. The EPDM/PE interface is rather blurred, because PE crystalline lamellae are growing into the EPDM domains, probably because of the high compatibility between PE and EPDM (60 wt% of ethene). This study shows that dynamic vulcanisation in extruders proceeds quite differently from that in batch kneaders, where melting, mixing and crosslinking are separated in time. In extruders mass and heat transport, melting of the thermoplastic, morphology development (including dispersion and phase inversion), distribution and dissolution of (crosslinking) chemicals and crosslinking of the rubber do not occur as independent phenomena, but mutually and/or continuously interact.     

基于Protel DXP的电路仿真设计

Protel DXP是集所有设计工具于一身的电子设计自动化(EDA)软件.文中运用其内嵌的仿真器叙述了分压式偏置电路放大器的仿真设计过程,设计过程简单、方便.在电子线路理论教学过程中引入电路设计仿真环节在不同情况下对电路进行实时分析,不仅可以提高学生的学习兴趣,而且能够在较短时间内加深学生对理论知识的理解;在工程设计过程中利用仿真工具对电路进行即时测试,可以缩短设计周期,提高设计效率.     

低压直流供电电路中高压直流的产生

在由低压直流电源供电的电路中,往往电路的某些部位需要使用高于电源所供的电压,将电源所供的低压转换为较高的电压,常用的方法有3种:自举升压、电感升压、逆变升压。结合实际应用电路对各种升压方法从器件选择、升压原理、升压结果等诸方面进行分析、探讨,解决了总体供电电压不变时,局部高压产生的关键性问题。它对电子电器电路的设计人员有一定的启发作用,对优化电路、遴选器件有较强的参考价值。     

天津独流减河工程监控系统现地通信单元设计

提出一种配电网电容电流测量的新方法，在零序电压互感器的开口三角侧串联一个可调电感，通过注入一个变频恒流信号寻找配电网的谐振频率，改变可调电感的数值后寻找另一谐振频率，联立2个谐振方程求解电容电流，该方法消除了电压互感器漏抗对测量的影响。开发了配电网电容电流测量仪，经模拟试验和现场测试表明，该方法具有安全、快捷、准确等特点，适用于中性点不接地或经随调式消弧线圈接地配电网。     

Prediction and quality control of the melt index during production of high-density polyethylene

In polyolefin processes the melt index (MI) is the most important control variable indicating product quality. Because of the difficulty in the on-line measurement of MI, a lot of MI estimation and correlation methods have been proposed. In this work a new dynamic MI estimation scheme is developed based on system identification techniques. The empirical MI estimation equation proposed in the present study is derived from the 1 ^st -order dynamic models. Effectiveness of the present estimation scheme was illustrated by numerical simulations based on plant operation data including grade change operations in high density polyethylene (HDPE) processes. From the comparisons with other estimation methods it was found that the proposed estimation scheme showed better performance in MI predictions. The virtual sensor model developed based on the estimation scheme was combined with the virtual on-line analyzer (VOA) to give a quality control system to be implemented in the actual HDPE plant. From the application of the present control system, significant reduction of transition time and the amount of off-spec during grade changes was achieved     

锌电积的节电探讨

分析厂影响锌电积电能消耗的因素，提出了锌电积的节电对策与展望。