利用视电阻率饱和度法分析稠油油藏动用状况

为了弄清稠油油藏蒸汽吞吐井附近油层的动用状况．利用侧钻井视电阻率饱和度分析法，研究电阻减小率与含油饱和度的关系．以确定蒸汽吞吐井附近油层的动用状况。实践证明，该方法切实可行，为调油油田蒸汽吞吐阶段油层动用程度研究，提供了一条新途径。     

高热流密度电加热元件

本文论述了用于液态金属钠热工水力性能研究的高热流密度模拟电加热元件的结构特点、材料选择、热电偶设置及其他与棒束传热实验研究有关的问题。     

大港白水头地区低阻油气层测井评价

在对白水头地区低阻油层的地质特征、物性特征及成因环境进行了分析研究后 ,应用测井曲线特征集法 ,把白水头油田常规油气层、低阻油气层、油水同层、水层等看成是独立的地质事件 ,建立了它们与测井曲线特征之间的对应关系 ,利用这种关系对未知地质事件进行了预测划分。最后根据所建模型定量计算储层各种参数 ,收到了良好的地质效果 ,表明测井曲线特征集法对于识别多成因的低阻油层是一种有效方法     

A comparative study of the gas sensing behavior of nanostructured nickel ferrite synthesized by hydrothermal and reverse micelle techniques

A comparative study of gas sensing behavior of nanocrystalline nickel ferrite synthesized by micro-emulsion and hydrothermal method to liquefied petroleum gas (LPG) is presented. Nanocrystalline nickel ferrite synthesized by hydrothermal method indicated higher electrical conductivity and gas sensitivity at low operating temperature compared to nanocrystalline nickel ferrite synthesized by reverse micelle technique. This difference in the gas sensing behavior can be attributed to the presence of more oxygen vacancies (i.e. non-stoichiometry) in the hydrothermally synthesized nickel ferrite. Incorporation of palladium had a catalytic effect and the operating temperature was significantly reduced in both the samples. The higher operating temperature of the reverse micelle nickel ferrite material makes the sensor response speed faster (∼10 s) compared to the hydrothermally synthesized material (∼1 min).     

Electrical conductivity and gas sensitivity of Zn-Sb-O thick films

The thick film of Zn-Sb-O was prepared by coating the paste of nanoparticles mixture (Sb₂O₃:ZnO=1:3) on the alumina substrate, followed by sintering at 500-900 °C for 2 h in air. The electrical resistance and gas-sensing properties to benzene, alcohol and acetone of Zn-Sb-O films were found to be dependent on the change of phase structure caused by sintering temperature.     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Preparation of multi-compositional gas sensing films by combinatorial solution deposition

Various compositions of gas sensing films were prepared by the combinatorial deposition of SnO₂, ZnO, and WO₃ sol solutions and their gas sensing behaviors were investigated. The film composition could be manipulated conveniently via the alternate dropping of different oxide sol solutions. From the correlation between film compositions and gas sensitivities, the selective detection of C₂H₅OH and CH₃COCH₃ in the presence of CO, C₃H₈, H₂, and NO₂ could be attained. In addition, the discrimination between C₂H₅OH and CH₃COCH₃, which is a challenging issue due to their similar chemical nature, becomes possible. This research demonstrates the precise design of the sensor-material composition for the selective gas detection via the combinatorial approach.     

Electrical characterization of homoepitaxial diamond p–n junction

Electrical properties of homoepitaxial diamond p–n⁺ junction of boron (B)-doped p-type layer and phosphorus-doped n-type layer on Ib (111) diamond single crystal have been characterized. Current–voltage characteristics show a clear rectifying property with rectification ratio of over 10⁵ at ± 10 V. From capacitance–voltage characteristics, it is found that a spatial distribution of space-charge density N_i of the p–n⁺ junction is not uniform and N_i at a middle region of the space-charge layer formed at zero bias voltage is higher than that of other region of the space-charge layer. This peculiar characteristic can be explained by superposition of two effects; one is the deep dopant effect due to B atoms in the p-type layer, which makes to reduce N_i at around the edge of the space-charge layer formed at zero bias voltage. The other is the compensation of B acceptors by impurity atoms diffusing during the p–n⁺ interface and incorporating during the growth of p-type layer, which makes to reduce N_i at the vicinity of the p–n⁺ interface.     

Passivation effects of deuterium exposure on boron-doped CVD homoepitaxial diamond

The deuterium (hydrogen) passivation effect on acceptors in boron-doped CVD homoepitaxial diamond was studied by electrical (Hall-effect) and secondary ion mass spectroscopy (SIMS) measurements. Deuterium was incorporated into the samples using microwave (MW) deuterium plasma at 673 K for 2–24 h. We observed the progress of acceptor passivation with p-type conduction, which finally resulted in a highly resistive state.     

Genetic synthesis of a fuzzy pulse discriminator in electrical discharge machining

In this paper, a sensor system, called a fuzzy pulse discriminator, is developed to classify various discharge pulses in electrical discharge machining (EDM). The fuzzy rules of the pulse discriminator are obtained based on the features of the gap voltage and gap current between the tool workpiece. The membership functions of the fuzzy pulse discriminator are automatically synthesized by using genetic algorithms. The effectiveness of this approach is verified under different cutting parameters.