Development of high‐definition aqueous polyvinylpyrrolidone photoresists for cathode ray tubes

Aqueous photoresists that are capable of higher resolutions than are currently employed by the cathode ray tube (CRT) industry were developed by combining photoactivators, which activate at shorter UV wavelengths with polyvinylpyrrolidone (PVP). Two photoactivators were synthesized: 4,4′‐diazido‐2,2′‐biphenyl disodium disulfonate (DABP), which has a maximum absorbance at 264 nm, and 4,4′‐diazido‐2,2′‐biphenylethane disodium disulfonate (DABPE), which has a maximum absorbance at 258 nm. The PVP/DABP and PVP/DABPE photoresists successfully imaged a pattern with resolution as small as 4.4 μm with photoactivator concentrations greater than 20% of the PVP concentration. Addition of silane and emulgen greatly improved the performance of the photoresists with more uniform coatings of thicknesses of up to 1.4 μm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1637–1644, 2006     

In-situ studies of electron field emission of single carbon nanotubes inside the TEM

Electron field emission characteristics of individual multi-walled carbon nanotubes (MWCNTs) were investigated in situ inside the transmission electron microscope (TEM). For a single MWCNT it was found that while field-emission can hardly occur from the side of the nanotube, a curved nanotube may result in finite side emission and the best emission geometry is the top emission geometry. Current-voltage (I-V) measurements made at different vacuum conditions and voltage sweeps emphasize the importance of the adsorbates on the electron field emission of MWCNTs. For a contaminated MWCNT, although the field emission current was reduced, the stability of its emission was improved. A current of up to several tens of μA was observed for a single MWCNT, but it was found that long time emission usually results in drastic structure damage that may lead to sudden emission failure.     

硫醇自组装膜的电化学研究进展

综述了在金电极上硫醇自组装膜的电化学表征方法，性质和应用，介绍了自组装膜上的电子传递机理，并进行了简要的展望。     

换热器管板厚度的快速计算

在化工生产中，换热器设备是应用最广泛的一种设备，且占主导地位。而在换热器设计过程中，管板厚度设计计算比较复杂。本文的特点是在满足GB151—1999《管壳式换热器》标准要求的前提下，介绍一种快速简便估算管板厚度的计算公式，从而达到快速确定管板厚度的目的。     

SYNTHESIS OF ACICULAR GOETHITE PARTICLES BY OXIDATION OF AQUEOUS FERROUS HYDROXIDE SUSPENSION IN A BUBBLE COLUMN WITH DRAFT TUBE

Acicular goethite particles were synthesized by oxidation of an alkaline suspension of ferrous hydroxide using a bubble column with draft tubes of different diameters at a constant temperature of 40°C. The oxidation rate increased with decreasing draft tube diameter. The mean size based on the major axis of acicular particle decreased with increasing oxidation rate and decreasing draft tube diameter. The major axis was found to grow preferentially compared with the minor axis. The mean size of major axis was correlated well to the modified reaction rate defined as a product of the reaction rate per unit volume of the reactor multiplied by the ratio of the column diameter to the draft tube diameter, irrespective of the draft tube diameter.     

Bulk and Interphase Effects in Aged Structural Joints

Although structural adhesives are becoming widespread in numerous applications, one important limitation at present is the long term behaviour of bonded assemblies under conditions of high humidity, especially at elevated temperatures. This study presents a comparison between bulk properties of a structural epoxy resin and its behaviour in a torsional joint consisting of a hollowed-out cylinder bonded to a plate—both substrates being in stainless steel. Exposure to ca. 100% relative humidity at 70°C leads to modification of the bulk properties of the polymer, notably reduction of its elastic modulus. Although this may explain some differences in behaviour of the torsional joint, premature failure is attributed to weaknesses in the interphase zone.

Auger Electron Spectroscopy (AES) has been employed to investigate both unbonded steel surfaces and fracture zones. Although prolonged exposure to water leads to a more extensive degree of (apparently) adhesive failure at the interface polymer/metal, AES has shown the presence of non-negligible quantities of carbon, attributed to residual polymer. Failure would seem to occur, at least partly, in a weak interphase of the polymer, near, but not at, the interface.

Various possible causes are evoked. For dry failure, residual polymer may be due to the topography of the metal surface and/or local modification of the adhesive during cure. In the case of aged joints, in addition there are potential effects due to swelling and differential stresses, secondary bond failure and molecular chain scission within the polymer, all provoked by the presence of water.     

考虑初始弯曲矩形薄壁钢管砼柱管壁屈曲分析

实际工程中的钢管都是有初始弯曲的,初始弯曲的存在会降低薄壁钢管混凝土柱的承载力.采用能量法对具有初始弯曲管壁的屈曲性能进行了分析,分析结果表明,初始弯曲的存在会使管壁的宽厚比降低30%左右.     

管板和传热管胀接应力应变的数值模拟及分析

蒸汽发生器是核电厂一回路与二回路的枢纽,传热管和管板的连接处为事故多发区,而机械加工过程残留的应力是引起裂纹的主要原因.应用有限元软件对某型蒸汽发生器中的传热管和管板的胀接过程进行瞬态模拟,得到不同胀接压力下的管板和传热管的残余应力和残余应变值,为传热管和管板最佳胀接参数的确定以及工作过程中应力腐蚀的预防提供理论依据.研究结果标明,管板孔表面的残余径向应力和残余径向应变值都是随胀接压力的增加而增加,且沿着轴向的变化规律相似.     

高精度冷轧不锈钢管生产

介绍了用ＬＤ型冷轧管机生产高精度冷轧不锈钢管的经验和质量保证措施。