The Clausius inequality corrected for heat transfer involving radiation

The objective of this paper is to prove that the Clausius inequality must be re-stated to have general applicability for heat transfer involving radiative fluxes. The integrand (đQ/T) of the Clausius expression applies to heat conduction and convection, but does not hold for most radiative transfer scenarios, with the exception of reversible infinitesimal net blackbody radiation transfer. In other cases involving radiative transfer, the equality holds for a cycle even though irreversible heat addition by radiative transfer occurs. This is without the erroneous presumption of entropy destruction anywhere in the cycle. Thus, the Clausius inequality indicates reversibility for a cycle that includes an irreversible process. Further, in some radiative cases the quantity đQ/T, where T is the boundary temperature, is not the entropy transfer at the system boundary, and in fact, primarily represents entropy production within the system. It is also clear that in another case considered, the quantity đQ/T had no physical meaning whatsoever. Consequently, the Clausius expression has been re-stated so that it is applicable to cycles with processes involving any form of heat transfer. A new integrand (đQ_cc/T + đS_Net,Rad) is presented, allowing the Clausius inequality to generally apply to all heat transfer scenarios. The work in this paper emphasizes the need to re-state other fundamental equations allowing applicability to all heat transfer processes, and draws attention to the unique character of radiative entropy calculations.     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Evaluating the transfer of technology between application domains: a critical evaluation of the human component in the system

Technology can take many forms from the development of sophisticated electronics to the application of basic procedural principles. Technology transfer can also take several forms, however, in this case, it is the transfer of technological principles between application domains that is of primary interest. This paper presents a framework (the Five ‘M’s framework) that can be used to consider the likely success of technology transfer. The framework is based upon a sociotechnical system approach. The framework is illustrated with an evaluation of the introduction of intelligent cruise control into motor vehicles. It is argued that this is a technological concept first developed as an aerospace application in the form of the autopilot. In this case, it is argued that the transfer of this technology in its current form may potentially compromise safety.     

我国风机盘管技术现状分析

介绍了近年来我国在风机盘管技术领域的最新成果，在结构形式、强化传热、提高室内空气品质、降低噪音和提高自动控制水平等方面的技术进展情况，分析了目前风机盘管中存在的问题，并对今后的发展方向进行了展望。     

Heat Transfer Analysis for Gas-to-Liquids Transportation Through Trans Alaska Pipeline

Gas-to-liquids (GTL) technology involves the conversion of natural gas to liquid hydrocarbons. In this article, theoretical studies have been presented to determine the feasibility of transporting GTL products through the Trans-Alaska Pipeline System (TAPS). To successfully transport GTL through TAPS, heat loss along the route must be carefully determined. This study presents heat transfer and fluid dynamic calculations to evaluate this feasibility. Because of heat loss, the fluid temperature decreases in the direction of flow and this affects the fluid properties, which in turn influence convection coefficient and pumping power requirements. The temperature and heat loss distribution along the pipeline at different locations have been calculated. Fairly good agreement with measured oil temperatures is observed. The powers required to pump crude oil and GTL individually, against various losses have been calculated. Two GTL transportation modes have been considered; one as a pure stream of GTL and the second as a commingled mixture with crude oil. These results show that the pumping power and heat loss for GTL are less than that of the crude oil for the same volumetric flow rate. Therefore, GTL can be transported through TAPS using existing equipment at pump stations.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

管内装元件强化传热的技术经济评价

提出了一种管内装元件强化传热的技术经济评价方法，此方法综合考虑了强化换热器管内传热膜系数的提高和管内流体阻力的增大，与普通的管壳式换热器相比，所带来的投资费用和使用费用变化，这个变化量可用净现值增量△NPV来表示。根据△NPV值来评价强化传热技术，从而为强化传热技术的开发和推广及进行决策提供指导。     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Synthesis and characterization of functional gradient copolymers of glycidyl methacrylate and butyl acrylate

Epoxy-functional spontaneous gradient copolymers of glycidyl methacrylate (G) and n-butyl acrylate (B) were synthesized via atom transfer radical polymerization (ATRP). The copolymerization reactions were carried out in toluene solution at 70 °C, using methyl 2-bromopropionate (MBrP) as initiator and copper chloride with N,N,N′,N′′,N′′-pentamethyldiethylenetriamine (PMDETA) as the catalyst system. The kinetic behaviour of the statistical copolymerizations was studied in a wide composition interval with molar fractions of G ranging from 0.10 to 0.75. The synthesized copolymers were characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. ¹H NMR was employed to determine the copolymer composition, demonstrating the gradient character of the copolymers along the main chain in the whole monomer conversion interval. Apart from this, the sequence distribution and stereoregularity were analyzed. These microstructural experimental data agreed well with those calculated from Mayo-Lewis terminal model (MLTM) and a Bernoullian statistic with an isotacticity parameter of σ_G = 0.28 and a coisotacticity parameter of σ = 0.30.