触摸调光控制芯片的设计与测试

电力作为一种方便的能源广泛应用于我们生活的各个方面,于是电能的节能变得尤为重要。由于家用照明设计可以从控制方面实现节能,因此人们可以根据自己不同时间的不同需要来调节灯光的亮度来达到节约电能的目的。本文提出了一种应用于家用照明亮度的调节控制芯片的设计方案,首先分析顶层模块的功能,再将其功能分类细化,分配到不同的子模块去实现,利用CMOS电压比较器来实现了过零检测、系统时钟脉冲产生、触摸控制等操作,并通过仿真软件验证了设计模块功能的正确性,最后经流片测试芯片功能满足设计要求。     

基于嵌入式系统的触摸屏驱动设计与实现

为了满足触摸屏性能良好、运行稳定精度高的要求,本文提出了一种基于嵌入式系统的触摸屏驱动设计与实现方法。本方案以S3C2410微处理器为核心,采用嵌入式操作系统,设计与实现触摸屏驱动程序,测试证明本驱动工作高效、稳定。     

自控产品在堆取料机控制系统上的应用

本文介绍堆取料机电气自控系统的结构设计、组态、控制原理，并结合SIEMENS自控产品PLCS7—300、变频器6SE70、触摸屏TP27、PROFIBUS网络通讯，对堆取料机自控系统做了重点论述。     

基于PLC的液压多路阀试验台设计

针对现有的液压多路阀试验台存在功能不全、可靠性差、测试精度和试验效率低等问题,设计了基于PLC的多功能液压多路阀试验台。该试验台由液压试验系统、操作台、PLC采集控制系统、触摸屏和上位计算机等组成。实际应用表明:该试验台可满足液控和电液比例控制液压多路阀的测试要求,且测试精度和试验效率高,可靠性强,用户界面友好。可为产品出厂测试、设计及维护提供实验支持。     

Touch sensor and photovoltaic characteristics of CuSbS2 thin films

Spin-coated chalcostibite CuSbS₂ thin films (≈500 nm thick) were fabricated and the influence of the drying temperature on the structural, morphological, optical and thermoelectric properties of the films was investigated. Crystalline phase-pure chalcostibite has been obtained for the films dried at 180 °C and 210 °C, while below 180 °C these films are partially amorphous. Surprisingly, at drying temperature of 240 °C, a Cu_xS secondary phase appeared. The increase of the drying temperature leads to the increase of the particle size and the decrease of the optical band gap, which is interesting for optoelectronic applications. The highest power factor value was achieved for the film dried at 210 °C, due to the inexistence of secondary phases, which allowed realizing a stable thermoelectric touch sensor with a V_signal/_noise of 5. In addition, this film was tested as a photovoltaic (PV) device and a power conversion efficiency (PCE) of 0.030% with an open-circuit voltage (V_OC) of 0.36 V, a short-circuit current density (J_SC) of 0.278 mAcm^?2 and a fill factor (FF) of 0.27 were obtained. Therefore, this work evidences a pathway toward developing bi-functional devices with simultaneously thermoelectric touch sensor and photovoltaic functions.     

Characterization of an acrylic polymer under hygrothermal aging as an optically clear adhesive for touch screen panels

Optically clear adhesives (OCAs) are key components of touch screen panels (TSPs). It is important that OCAs do not affect the transparent electrodes in TSPs because OCAs are contacted to the transparent electrodes. Therefore, N-vinyl caprolactam (NVC) was incorporated in the composition of an acrylic pressure sensitive adhesive (PSA) with excluding an acidic component to maintain the cohesion for OCA preparation. With increasing amounts of NVC, the tack and peel strength of UV-cured PSA increased, but high amounts of NVC led to decreased peel strength. The UV-cured PSA films were placed in a high temperature and humidity chamber for 8 weeks to investigate the durability and corrosion property under hygrothermal conditions. In this study, the corrosion test method using copper foil was suggested as a simple and economical method and was used to evaluate the effect of NVC on the corrosion property of PSA. This method helped identify suitable OCAs that do not have corrosive property. PSA films containing more than 20 wt% of NVC promoted the corrosion of copper foil under hygrothermal aging conditions. The caprolactam ring was opened by moisture, and the PSA structure morphed into a polar structure during the aging process. This change caused a glass transition shift, an increase in the storage modulus at the rubbery plateau, and an increase in peel strength. The surface free energy of the PSA films also increased due to the increase in the polar property. However, high amounts of NVC caused a decrease in the peel strength after 8 weeks of aging because of increased molecular interactions.     

变电站接地网优化设计

在不等电位数学模型下,以网内最大接触电压差为目标函数,使用接地网工频参数计算软件得到了一种均匀土壤结构下接地网导体最优布置方案。优化结果表明,与DL/T621-1997中给出的接地网不等间距布置相比较,故障电流入地点处导体得到了充分利用,相应地减小了边缘导体泄漏电流,改善了土壤表面的电位分布,使接地系统的安全性得到明显提高。     

基于PLC和触摸屏的平衡块整形分拣系统

本文介绍了由PLC、触摸屏和单片机电子秤构成的用于汽车车轮平衡块自动称重分拣与整形系统。在对比PLC、触摸屏和单片机电子秤的性能基础上,编制了控制程序,合理利用各自功能与优势并实现了PLC、触摸屏和单片机电子秤之间通讯与数据交换。通过实际样机的运行,验证所设计的控制系统正确与有效。     

基于气压传动和触摸屏的智能烫印机研发

针对当前烫印机采用薄膜轻触面板型人机界面交互性差、无网络功能、信息化和自动化水平低等问题,设计开发了一种新型智能烫印机。采用基于T5内核的串口电容触摸屏,实现了烫印工艺多模式交叉配置,提升了设备适应当前小批量定制化生产需求的能力。基于T5触摸屏集成的网络接口,实现了远程监控、算法升级、网络化生产管理。嵌入式控制系统以STM32F10系列32位高性能微控制器为核心,集成了烫印胶头温度测控模块和伺服电机驱动模块。采用UL2068达林顿管全数字化驱动气缸,高速全自动完成移印过程。实践应用表明:所开发的烫印机性能稳定,实现了烫印工艺、烫头恒温、伺服电机、高速气缸高性能一体化全自动控制。该烫印机集成度高,触摸屏显示界面友好,能够实现网络化控制与管理,具有广阔的工程应用前景。     

西门子PLC和Pro—face HMI在空调末端控制系统中的应用

该文介绍了西门子PLC和Pro-face HMI在空调末端控制系统中的应用,着重从系统结构、硬件和软件系统的特点以及人机界面（HMI）的典型画面设计等方面进行了描述。