激光法合成纳米金刚石的高分辨电镜研究

在常温常压下,采用脉冲激光作用循环的石墨悬浮液,收集并烘干得到样品B,另一部分用高氯酸进行酸煮提纯提到样品A.对样品A、B分别进行高分辨电子显微镜（HRTEM）和显微拉曼光谱（Micro-Raman）分析.结果表明,部分石墨经激光作用后转变成了具有多重孪晶结构特征的、尺寸为5 nm的金刚石颗粒,同时还得到了非晶碳.高分辨电子显微镜照片证明,石墨转变成纳米金刚石的机理为快速成核长大过程.     

Effect of selective laser melting on microstructure and properties of AZ91D alloy

Selective laser melting technology is used to manufacture porous and solid AZ91D alloys. The effects of laser power and hatch spacing on the density, blowholes, microstructure and mechanical properties of AZ91D alloy are studied. The laser power and hatch spacing play a significant role in the density and blowholes of AZ91D specimens. The grains size of specimens increases from 1 μm–2 μm to 8 μm–10 μm from the bottom to the top in single molten pool. Compared with grain size of die‐casting alloy (30 μm), that of selective laser melted gets refinement. There is no significant change in microstructure in the bottom, middle and top of specimens. The micro‐hardness of AZ91D alloy, reaching up to 115.3 HV 0.1, is superior to that of die‐casting alloy (56 HV 0.1). The compression properties of porous and solid specimens reach the degree of die‐casting solid magnesium alloy. AZ91D alloy shows the potential in the application of medical biodegradable materials.     

Characteristics of Ions Emitted from Laser-Induced Silver Plasma

In this work, study of laser-induced ions is presented. The plasma was produced by focusing a Nd：YAG laser, with a wavelength of 1064 nm, a pulsed width of 9-14 ns, a power of 1.1 MW and energy of 10 mJ, on silver target in vacuum （10-3 Torr= 1.3332 Pa）. The characteristics of ion streams were investigated by CR-39 detectors located at angles of 0°, 30°, 60° and 90° with respect to normal of the target. The distance between the silver target and each detector was 11 cm. The energy of silver ions was found ranging from 1.5 eV to 1.06E4 eV. There was a high concentration of ions with low energy as compared to those with high energy, showing the energy distribution amongst the ions. The flux of ions was maximum in the axial direction which was decreasing with the angle increase with respect to normal of the target, and finally became minimum in the radial direction. Hence the silver ions have shown anisotropic behaviour.     

125 MN挤压机挤压中心在线监测系统设计

125 MN挤压机挤压中心检测目前采用人工测量计算法,工作量大且精度低.本文在分析常见光电位置检测方法的基础上,结合激光技术和图像处理技术,设计了一种新的挤压中心在线监测系统.阐述了该监测系统的原理和实施方案,建立了中心偏移量和偏转角度计算的几何模型,推导了计算公式,进行了模拟试验并做了误差分析.系统可同时对穿孔横梁、穿孔动梁、固定横梁、活动横梁和挤压容室进行在线监测,监测距离达35 m.     

基于卡尔曼滤波的InSAR柔性基线距离测量

对于柔性长基线构型的双天线InSAR系统,基线矢量动态偏移产生的误差会降低系统的成像质量,并最终影响高程精度。针对单相机和激光测距仪组合测量系统中如何提高基线距离向精度的问题,提出了一种基于卡尔曼滤波的基线距离测量方法。建立了基线距离向抖动数学模型,在此模型基础上提出了基于卡尔曼滤波的动态测量方法,对该方法进行了动态仿真分析。仿真结果表明,在几十米的测量距离内,该方法能够将基线距离向的测量精度降低到亚毫米量级,是测量基线距离的有效方法。     

大行程位移台干涉测距系统的误差补偿

双频激光干涉仪作为常用的精密光学非接触式测量设备,具有精度高、抗干扰能力强、灵活性好等优点。然而环境温度变化、机械振动等因素可能会影响其测量结果的准确性,并且影响程度会随着测量光程的增加而增大。针对基于双频激光干涉仪的大行程位移台测距系统,首先研究了位移台测距系统的测量原理,然后针对系统存在的各项误差进行了分析和补偿,最后,对系统进行综合误差补偿实验,短时间补偿量达到10^-8 m量级,且时间越长补偿效果越好。该方法较现有的误差补偿方法更为完整,补偿量更大。     

基于DFB激光器的振动传感系统改进PGC解调算法

相位生成载波(Phase Generated Carrier, PGC)解调算法是目前光纤干涉传感领域中重要的解调算法。针对目前PGC解调算法中光强扰动和调制深度影响信号解调准确度的问题,提出了一种改进的PGC解调算法(PGC-Ameliorated),并搭建了基于分布反馈(Distributed Feedback, DFB)激光器的振动传感系统进行实验验证。实验结果表明,当被测振动信号的频率为800 Hz时,该算法信噪比为57 dB,优于微分交叉相乘(Differential and Cross Multiplying, DCM)算法和反正切(Arctan)算法近20 dB。在不同光强下,该算法解调信号幅值波动范围在±0.02 rad;在不同调制深度下,该算法总谐波失真最小为0.61%,信纳比最大为25.9 dB,相比于DCM算法和Arctan算法具有更低的总谐波失真和更高的信纳比。     

自动送粉激光熔覆装置及工艺研究

研制了一种工作稳定性好、粉末流量连续可调的自动送粉装置。经A_3钢表面激光熔覆WF-150不锈钢合金粉末的研究表明,所获得的激光熔覆层均匀连续、无宏观气孔和裂纹,粉末利用率高达94％。