N-苄基丙烯酰胺的合成

以丙烯腈和苯甲醇为原料，浓硫酸作催化剂，合成了N-苄基丙烯酰胺（N-BAA）。考察了反应温度、反应时间和催化剂用量等因素对产物收率的影响，得出了最佳反应条件：n（丙烯腈）：n（苯甲醇）：n（浓硫酸）=3：1：1．2，反应时间3h，反应温度60℃。在最佳条件下，N-BAA的收率可达92％。每100g粗产物用10％氢氧化钠溶液提纯，精制产物纯度可达99．80％，熔点为64～65℃。通过红外光谱对产物结构进行了表征。     

Evaluation of the Properties of Si3N4/Si3N4 Joint Brazed Using a Filler Alloy Containing Pd

Si3N4 ceramic was jointed to itself using a filler alloy of Cu76.5Pd8.5Ti15, and the mechanical properties of the jointwere measured and analyzed. By using a filler alloy of Cu76.5Pd8.5Ti15, the SisN4/SisN4 joints were obtained bybrazing at 1373～1473 K f     

遗传算法在GSM移动通信网络频率规划中的应用

应用遗传算法设计和开发了针对爱立信GSM900系统的频率规划软件。在设计中，采用了交叉点存储、变异回退以及分割分步降维的方法，从而提高遗传算法的执行速度。     

线性调频信号检测方法的研究

在线性调频信号体制雷达的数字脉冲压缩系统中对数字脉压后的脉冲串进行DFT相参处理时，若采样时刻偏离脉压回波的峰值时刻，不同的采样频率使得DFT相参积累后的信噪比会有不同程度的损失。本文详细分析了采样频率分别为20MHz和10MHz时对信号相参积累的影响，并对幅值检测和M／N检测两种检测方法的检测性能进行了比较，仿真结果表明，M／N检测优于幅值检测。     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Electrical and growth characteristics of Au/Al0.15Ga0.85N:Si structures with various Si incorporations

We have investigated the growth characteristics of n-Al_0.15Ga_0.85N:Si/GaN and the electronic properties of Au/n-Al_0.15Ga_0.85N:Si diode structures grown by metal-organic chemical vapor deposition (MOCVD) with various Si incorporations. The Al_0.15Ga_0.85N:Si layers were grown on undoped GaN/sapphire (0001) epitaxial layers in a horizontal MOCVD reactor at the reduced pressure of 300 torr. The mirrorlike surface, free of defects, such as cracks or hillocks, can be seen in the undoped Al_0.15Ga_0.85N epilayer, which was grown without any intentional flow of SiH₄. However, many cracks are observed in the n-Al_0.15Ga_0.85N:Si, which was grown with Si incorporation above 1.0 nmol/min. While Au/n-Al_0.15Ga_0.85N:Si diodes having low incorporation of Si showed retively good rectifying behavior, the samples having high Si incorporation exhibited leaky current-voltage (I-V) behavior. Particularly, the Au/n-Al_0.15Ga_0.85N:Si structure grown with Si incorporation above 1.0 nmol/min cannot be used for electrical rectification. Both added tunneling components and thermionic emission influence the current transport at the Au/n-Al_0.15Ga_0.85N:Si barrier when Si incorporation becomes higher.     

Influence of ethyl methacrylate content on the volume‐phase transition of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] microgels

A novel series of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] (p(NIPAM‐co‐EMA)) microgels was prepared by the surfactant‐free radical polymerization of N‐isopropylacrylamide (NIPAM) with ethyl methacrylate (EMA). The shape, size dispersity and volume‐phase transition behavior of the microgels were investigated by transmission electron microscopy (TEM), ultraviolet–visible (UV–Vis) spectroscopy, dynamic light scattering (DLS) and differential scanning calorimetry (DSC). The transmission electron micrographs and DLS results showed that microgels with narrow distributions were prepared. It was shown from UV–Vis, DLS and DSC measurements that the volume‐phase transition temperature (VPTT) of the p(NIPAM‐co‐EMA) microgels decreased with increasing incorporation of EMA, but the temperature‐sensitivity was impaired when more EMA was incorporated, causing the volume‐phase transition of the microgels to become more continuous. It is noteworthy that incorporation of moderate amounts of EMA could not only lower the VPTT but also enhance the temperature‐sensitivity of the microgels. The reason for this phenomenon could be attributed to changes in the complicated interactions between the various molecules. Copyright © 2004 Society of Chemical Industry     

Active sites of Cu-ZSM-5 for the decomposition of acrylonitrile

The catalytic decomposition of acrylonitrile (AN) over Cu-ZSM-5 prepared with various Cu loadings was investigated. AN conversion, during which the nitrogen atoms in AN were mainly converted to N₂, increased as Cu loading increased. N₂ selectivities as high as 90–95% were attained. X-ray diffraction measurements (XRD) and temperature-programmed reduction by H₂ (H₂-TPR) showed the existence of bulk CuO in Cu-ZSM-5 with a Cu loading of 6.4 wt% and the existence of highly dispersed CuO in Cu-ZSM-5 with a Cu loading of 3.3 wt%. Electron spin resonance measurements revealed that Cu-ZSM-5 contains three forms of isolated Cu²⁺ ions (square-planar, square-pyramidal, and distorted square-pyramidal). The H₂-TPR results suggested that in Cu-ZSM-5 with a Cu loading of 2.9 wt% and below, Cu⁺ existed even after oxidizing pretreatment. The activity of AN decomposition over Cu/SiO₂ suggested that CuO could form N₂, but, independent of the CuO dispersion, nitrogen oxides (NO_x) were formed above 350 °C. Cu⁺ and the square-pyramidal and distorted square-pyramidal forms of Cu²⁺ showed low activity for AN decomposition. Temperature-programmed desorption of NH₃ suggested that N₂ formation from NH₃ proceeded on Cu²⁺, resulting in the formation of Cu⁺. The Cu⁺ ions were oxidized to Cu²⁺ at around 300 °C. Thus, high N₂ selectivity over Cu-ZSM-5 with a wide range of temperature was probably attained by the reaction over the square-planar Cu²⁺, which can be reversibly reduced and oxidized.     

单微乳液中制备Ag/TS-1及丙烯气相环氧化

采用N2H4还原含AgNO3的单微乳液制备了Ag／TS-1催化剂。TEM表征结果表明，Ag高度分散于TS-1之上。以H2、O2存在下的丙烯气相环氧化为探针反应，考察了Ag／TS-1的催化性能。结果表明，采用Ag／TS-1为催化剂，Ag的负载量为1％（质量分数，下同），823 K焙烧后，373 K下反应30 min时，丙烯转化率为1．69％，环氧丙烷（Propylene oxide，PO）选择性为93．2％。当Ag的负载量超过2％时，反应过程中生成大量的热，造成PO的选择性下降。采用Ag的负载量为8％的Ag／TS-1催化剂，消除热效应后，丙烯的转化率为2．46％．PO的选择性为79．2％。