用Visual C++实现PLC实时监控

用VisualC + +和MFC开发了上位机和PLC的通讯系统 ,给出了系统的通讯原理和软件设计方法。运行结果表明 ,此方法简单、稳定、实用性强     

用scanf()函数输入浮点数出现问题的解决办法

本文讨论了用scanf()函数输入浮点数出现的问题,并分析了该问题产生的原因,最后文章重点给出了针对这类问题的4种解决方案。     

Effects of lubrication and humidity on the abrasiveness of a thin boron carbide coating

Studies using thin boron carbide (B₄C) coatings have previously been performed in order to investigate their potential use as finite-life run-in coatings. Such coatings have been shown to polish the mating surface in a relatively short time. The inherent ability of these coatings to polish can potentially allow them to function as finite-life run-in coatings. Employing such coatings requires a thorough understanding of the parameters which directly influence the changes that occur in the coating abrasiveness throughout the duration of the polishing process. In past studies, changes in the coating abrasiveness during dry sliding wear under ambient conditions have been investigated. However, both lubrication and humidity can strongly influence the abrasive wear process. In this study, the influences of the operating environment, namely humidity and lubrication, on the coating abrasiveness are directly investigated. The coating abrasiveness decreases at a slower rate when a lubricant is added and when the humidity decreases.     

甘肃某金矿选矿试验研究

根据国内某金矿载体矿物的性质,进行了详细的选矿条件试验,获得了较优的工艺参数,最终确定了“一粗两精两扫,中矿顺序返还”的工艺流程。闭路试验结果表明：在磨矿细度为一0．074mm占70％的条件下,可获得产率2．89％、品位85．16g／t、回收率82．17％的金精矿。     

A ctivation measurement of neutron distribution in intermediate energy heavy ion target area

The distribution of neutrons produced by the reaction of 50MeV/u ^12C-ion on a thick Cu target are studied.The neutrons are measured with threshold activation detectors.Al.F,C,Al and In activation samples were used to measure neutrons with energy greater than 7,11,20,50MeV and thermal neutrons,respectively,The fluence rate,energy and angular distributions of neutrons,total neutron yield of 12C-ion and the emission rate in the forward direction of neutrons over 11 and 20MeV were obtained.     

树脂浸渍补充增密对C/C复合材料摩擦磨损性能的影响

将CVD预增密至不同初始密度的C／C复合材料进行树脂浸渍／炭化补充增密至1.85g/cm^3，热处理后进行热物理性能的检测和不同刹车压力的摩擦磨损试验。结果表明，树脂浸渍／炭化是一种行之有效的快速致密化手段，所得制品的可石墨化性较好，导热性能也满足国外同类产品的要求；摩擦磨损试验和扫描电镜（SEM）观察结果表明，低一压力下形成的磨屑粒度明显大于高压下的磨屑，因而低压下的摩擦数高于高刹车压力下的摩擦系数。低压下的树脂炭对摩擦磨损的影响相对较大。     

轧机主传动直流电动机通风冷却系统的设计与应用

通过实例简述了扎机主传动直流电动机通风冷却系统的风机选择原则,方法及其风机房,风机基础和通风管略的设计与应用。     

粮油食品机械设计中凸轮轮廓CAD的探讨

用Ｃ 语言编程计算凸轮轮廓数据并构造凸轮轮廓计算函数库。在ＡｕｔｏＣＡＤ 平台下,利用ＡｕｔｏＬＩＳＰ语言程序,完成了粮油食品机械设计中凸轮轮廓计算机辅助设计（ＣＡＤ） 。解决了传统设计方法存在的设计周期长、自动化程度低等问题。大大提高了粮油食品机械设计的工作效率和工作质量,实现了凸轮轮廓设计、绘图整个过程的自动化。     

CCD在桥梁振动检测中的应用

根据桥梁振动检测的工作特点及要求,为实现非接触、动态自动化检测,基于CCD远距离、非接触测量技术,采用硬件电路设计完成了与USB端口的数据传输,通过确定固定条码标尺中心位置的上下偏移量实现对桥梁状态的检测.采用Visual C 6.0作为开发环境,完成了用户应用程序.该方法具有测量精度高、操作简便、性价比高等优点,非常便于野外作业,在实际检测中得到很好的应用.     

并行设备总线嵌入式控制系统设计

采用ARM7内核芯片S3C4510的高性能网络控制器结合使用CPLD设计VME总线控制器逻辑时序,研制出了类似3UVME的并行设备总线控制器。开发嵌入式系统uClinux的网络通讯软件,实现提供设备之间高速网络连接通道,把后台计算机数据库和前端设备紧密地连接起来,实现数据的快速获取与给定。