Design of a printed log‐periodic dipole array antenna with high gain for millimeter‐wave applications

In this article, a V‐band printed log‐periodic dipole array (PLPDA) antenna with high gain is proposed. The antenna prototype is designed, simulated, fabricated, and tested. Simulation results show that this antenna can operate from 42 to 82 GHz with a fractional impedance bandwidth of 64.5% covering the whole V‐band (50–75 GHz). The antenna has a measured impedance matching bandwidth that starts from 42 to beyond 65 GHz with good agreement between the experimental and simulated results. At 50 and 65 GHz, the antenna has a measured gain of 10.45 and 10.28 dBi, respectively, with a gain variation of 2.6 dBi across the measured frequency range. The antenna prototype exhibits also stable radiation patterns over the operating band. It achieves side‐lobe suppression better than 17.26 dB in the H‐plane and better than 8.95 dB in the E‐plane, respectively. In addition, the cross‐polarization component is 18.5 dB lower than the copolarization with front‐to‐back ratio lower than 24.1 dB in both E‐ and H‐planes across the desired frequency range. Based on a comparison of performance among the reported work in the literature, we can say that the proposed PLPDA antenna is a proper candidate to be used in many applications at V‐band frequency. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:185–193, 2015.     

Millimeter‐wave planar high gain SIW antenna using half elliptic radiation slots

This article reports a high gain millimeter‐wave substrate integrated waveguide (SIW) antenna using low cost printed circuit board technology. The half elliptic slots which can provide small shunt admittance, low cross polarization level and low mutual coupling are etched on the board surface of SIW as radiation slots for large array application. Design procedure for analyzing the characteristics of proposed radiation slot, the beam‐forming structure and the array antenna are presented. As examples, an 8 × 8 and a 32 × 32 SIW slot array antennas are designed and verified by experiments. Good agreements between simulation and measured results are achieved, which shows the 8 × 8 SIW slot array antenna has a gain of 20.8 dBi at 42.5 GHz, the maximum sidelobe level of 42.5 GHz E‐plane and H‐plane radiation patterns are 22.3 dB and 22.1 dB, respectively. The 32 × 32 SIW slot array antenna has a maximum measured gain of 30.05 dBi at 42.5 GHz. At 42.3 GHz, the measured antenna has a gain of 29.6 dBi and a maximum sidelobe level of 19.89 dB and 15.0 dB for the E‐plane and H‐plane radiation patterns. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:709–718, 2015.     

Novel ultra‐compact two‐dimensional waveguide‐based metasurface for electromagnetic coupling reduction of microstrip antenna array

A novel ultracompact two‐dimensional (2D) waveguide‐based metasurface is proposed herein and applied for the first time to reduce mutual coupling in antenna array for multiple‐input multiple‐output applications. The unit cell of the proposed 2D waveguide‐based metasurface is ultracompact (8.6 mm × 4.8 mm, equal to λ₀/14.2 × λ₀/25.5) mainly due to the symmetrical spiral lines etched on the ground. The metasurface exhibits a bandgap with two transmission zeros attributing to the negative permeability in the vicinity of magnetic resonance and the negative permittivity in the vicinity of electric resonance. Taking advantage of these two features, a microstrip antenna array is then designed, fabricated, and measured by embedding an 8 × 1 array of the well‐engineered 2D waveguide‐based metasurface elements between two closely spaced (9.2 mm, equal to λ₀/13.3) H‐plane coupled rectangular patches. There is good agreement between the simulated and measured results, indicating that the metasurface effectively reduces antenna mutual coupling by more than 11.18 dB and improves forward gain. The proposed compact structure has one of the highest reported decoupling efficiencies among similar periodic structures with comparable dimensions. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:789–794, 2015.     

Modeling of microstrip antennas using neural networks techniques: A review

Artificial neural networks modeling have recently acquired enormous importance in microwave community especially in analyzing and synthesizing of microstrip antennas (MSAs) due to their generalization and adaptability features. A trained neural model estimates response very fast, which is nearly equal to its measured and/or simulated counterpart. Thus, it completely bypasses the repetitive use of conventional models as these models need rediscretization for every minor changes in the geometry, which itself is a time‐consuming exercise. The purpose of this article is to review this emerging area comprehensively for both analyzing and synthesizing of the MSAs. During reviewing process, some untouched cases are also observed, which are essentially required to be resolved for antenna designers. Unique and efficient neural networks‐based solutions are suggested for these cases. The proposed neural approaches are validated by fabricating and characterizing of the prototypes too. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:747–757, 2015.     

A compact asymmetric slot dual band antenna fed by CPW for PCS and UWB applications

A compact slot antenna with an overall dimension of 30 × 30 × 1.6 mm³ is proposed for dual band applications. The radiating element is a hexagonal shape patch which protrudes from a Co‐Planar Waveguide (CPW) feed into a step shape slot. The slot is basically rectangular in shape and is extended by inserting rectangular cuts of different sizes on the ground plane around it. The ultrawide impedance bandwidth is achieved using asymmetric feed line along with extended rectangular cuts around the slot. For realizing the second band for personal communication system applications (near 1.9 GHz), a metallic stub of quarter wave length is attached at the top of the slot. The measured impedance bandwidth (for S₁₁ < ?10 dB) is 110 MHz (1.86–1.97 GHz) for the first band and 9 GHz (3.0–12.0 GHz) for the second band. The antenna is further characterized by omnidirectional radiation patterns in the H‐plane, dumb‐bell shape radiation patterns in the E‐plane and a peak gain of 3–5 dBi over the ultrawideband. All the measured results are found to be in good agreement with the simulated results. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:243–254, 2015.     

一种高增益宽频带圆极化微带阵列天线的研制

针对微带天线阻抗匹配带宽一般较窄的自身缺陷,基于相控阵雷达天线的应用背景,设计了一种工作在X波段的双层圆极化微带天线结构,且优化发现,其各电磁参数良好。为提高其增益,还在此基础上设计并最终制作了双层2×2结构的微带天线阵列,其实测性能与设计值相符,增益达到10.7dB,带宽1.2GHz,相应轴比为4dB,符合圆极化要求。     

A low‐profile,low‐cost antenna system with improved gain for DSRC vehicle‐to‐vehicle communications

A novel wire antenna for future dedicated short range communications vehicle‐to‐vehicle communications is introduced. The proposed antenna carries low‐profile and low‐cost features, and possesses an improved gain performance. This article also includes a specific feed network design for the proposed antenna to meet the mechanical and manufacturing requirements. Two different numerical techniques using CST Microwave Studio and HFSS have been applied for evaluating the performance of the proposed antenna. The whole system including the feed network and the antenna elements is integrated, and its performance is also assessed. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Bacteria foraging optimization in antenna engineering: An application to array fault finding

Finding fault elements in linear antenna arrays using bacteria foraging optimization (BFO) is presented. One of the better options of array diagnosis is to perform it by measuring the radiated field, because in this case, removal of the array from its working site is not required and thereby not interrupting its normal operation. This task of fault finding from far‐field data is designed as an optimization problem where the difference between the far‐field power pattern obtained for a given configuration of failed element(s) and the measured one is minimized w. r. t. the excitations of the array elements. This set of excitations on comparison with the excitations of the original array gives the idea of the fault position and their type, such as either complete fault or partial fault. BFO being relatively new to microwave community when compared with other soft‐computing techniques, its performance was observed w. r. t. time of computation and convergence of the iterative process. Possibility of finding the faults from random sample points and use of minimum number of sample points for array fault finding are the novelties of the present work. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Improved phase performance for rotman lens

Rotman lenses are used to obtain multiple beams from a single array. Although the beams produced by the feed antennas at focal points have no path length errors, the beams produced by feed antennas at off focal points may have large path length errors. These path length errors cause deterioration in the multiple beams. In this article, two novel methods are introduced to obtain feed curves which reduce the path length errors of off focal feed points significantly, compared with the commonly used circular and elliptical feed curves. The first method obtains feed curve points based on having zero path length error at three chosen points of the radiating array for each beam direction. The second method uses the particle swarm optimization method for obtaining optimum feed points for each beam direction. The results show that there is a very significant drop in the level of the maximum path length errors (in the order of about 1:4). © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE 23: 634–638, 2013.     

Design of hexa‐band planar inverted‐F antenna using hybrid BSO‐NM algorithm for mobile phone communications

This article presents a new design of multiband planar inverted‐F antenna with slotted ground plane and S‐etched slot on the radiation patch. The proposed antenna is optimized using an efficient global hybrid optimization method combining bacterial swarm optimization and Nelder‐Mead (BSO‐NM) algorithm to cover a very important six service bands including GSM900, GPS1575, DCS1800, PCS1900, ISM2450, and 4G5000 MHz with enhanced bandwidths. The BSO‐NM algorithm in Matlab code is linked to the CST Microwave studio software to simulate the antenna. To validate the results, the antenna is analyzed using the finite difference time domain (FDTD) method. A good agreement is achieved between the results of EM simulation and that produced from the FDTD method. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.