CAST的工作原理与设计计算

详细论述了循环式活性污泥法(CAST)的工作原理，对该工艺的设计计算作了探讨，提出了设计方法，并提供了有关计算公式和操作时间分配。     

标准型直燃机在严寒地区应用探讨

介绍了标准型直燃机的分类、原理及长庆至呼和浩特输气管道工程冷冻供热站的设计实例 ,重点论述了标准型直燃机在严寒地区使用的利弊     

Red emission from Eu3+: PVA polymer film

Bright red luminescent Eu³⁺ doped polyvinyl alcohol (PVA) films were made by solution casting technique. The emission performance of these films was studied from the measurement of excitation, emission, and lifetimes. On irradiation with an UV source, the doped films emitted bright red light. Such luminescent polymer films are expected to find potential applications as new optical materials. Emission process in the system was explained by an energy level scheme. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3273–3276, 2006     

遵义后坝奥陶系红花园组油苗岩石轻烃特征分析

遵义后坝奥陶系红花园组生物碎屑灰岩中发现油苗和沥青,经过气/源岩、沥青/源岩对比,震旦、寒武及奥陶系产层轻烃C₆₊₇结构组成基本一致,奥陶系含油苗灰岩轻烃星图与震旦系泥岩、寒武系沥青砂岩星图较为相似,显示红花园组油苗主要来源于震旦系和下古生界过成熟或高成熟海相烃源岩,油气经历了较长距离的运移,得以在奥陶系中保存下来。这对评价该地区油气前景有重要意义,预示着可能存在一套特殊的含油气组合,存在以O₁h古风化壳储集层为目的层的勘探领域。在兴文—叙永一线以西地区现今下古生界储盖组合保存良好,在适当的构造圈闭中可形成油气藏。志留系和二叠系产层轻烃C₆₊₇与震旦系、寒武系及奥陶系等产层轻烃C₆₊₇明显有别,星图对比性差,表征它们之间成烃母质或沉积环境均有不同。      

转子--轴承系统油膜失稳故障预测准则的探索

采用稳态非线性轴承理论，以多自由度转子系统为对象，运用模态降阶和变步长的Newmark积分方法，对非线性油膜力作用下轴颈振动的涡动轨迹、频谱及失稳前后的特征进行详细的计算分析，同时分析转子不平衡量的大小和转速对系统振动行为及其稳定性的影响。通过分析给出处于临界稳定状态的转子系统的轴心轨迹及其频谱图特征，这些结果有望对油膜失稳故障的预测和防范提供有应用价值的理论依据。     

甲醇气相氧化羰化合成碳酸二甲酯 Ⅲ.复合载体铜基催化剂的表征

采用X射线衍射、表面物理吸附、CO原位吸附红外光谱、X射线光电子能谱以及热重分析方法对甲醇直接气相氧化羰化合成碳酸二甲酯的复合载体铜基催化剂(Cu(Ⅱ)/Naβ-AC)的物化性能进行了表征。实验结果表明,微波辐射条件下制备的Cu(Ⅱ)/Naβ-AC催化剂中,活性组分CuC l2一方面与分子筛载体间发生了固相离子交换反应,并形成了铜分子筛物种,另一方面,可直接高度分散在复合载体表面。反应后Cu(Ⅱ)/Naβ-AC催化剂中部分Cu2+被还原为Cu+或Cu0,Cu2+的结合能峰向低结合能方向迁移,但微波辐射处理并未破坏分子筛载体的骨架结构。采用复合载体增加了催化剂的比表面积,并产生一定量的微孔,从而提高了催化剂的氧化羰化反应活性。热重分析表明,当温度低于350℃时,Cu(Ⅱ)/Naβ-AC催化剂稳定性较好。     

Single and combined deactivating effect of alkali metals and HCl on commercial SCR catalysts

Two commercial SCR catalysts, with a nominal W content of about 9 wt.% and a V nominal content of 0.55 and 1.8 wt.%, respectively, were contacted with different amounts of Na and K and with HCl vapours in order to simulate poisoning by species more specifically contained in exhaust gases from MSW combustion. Catalysts were characterised using XRD analysis, SEM/EDX analysis, BET and pore size distribution measurements, NH₃ TPD, TG analysis. Poisoning agents do not cause loss of surface area nor pore occlusion. A significant loss of surface acidity was observed upon alkali metals poisoning whereas a decreasing of vanadium content was observed for the more concentrated catalysts upon HCl poisoning. Catalysts deactivation is proportional to the number of acid sites neutralised by alkali metals adsorbing ammonia in the temperature range typical of SCR process. HCl promotes the formation of new acid sites showing a lower activity compared to the original one.     

脉冲激光淀积高电流密度的YBCO超导带材

采用脉冲激光加辅助离子源的方法在长为６．０ｃｍ的ＮｉＣｒ合金基带上制备０．１３μｍ厚的Ｙ－ＺｒＯ２（ＹＳＺ）隔离层，再用脉冲激光在ＹＳＺ／ＮｉＣｒ带上制备１．５μｍ厚的ＹＢａ２Ｃｕ３Ｏ７－ｘ超导厚膜形成ＹＢＣＯ／ＹＳＺ／ＮｉＣｒ超导带材。实验测得在７７Ｋ，０Ｔｅｓｌａ下其临界电流密度为８．７５×１０４Ａ／ｃｍ２，超导转变温度为８８．６Ｋ。     

Electrical properties at p-ZnSe/metal interfaces

In order to prepare low resistance ohmic contacts to p-ZnSn by the “deposition and annealing (DA)” technique which has been extensively used for GaAs and Si-based devices, formation of a heavily doped layer by the p-ZnSe/metal reaction is required. For p-ZnSe/Ni contacts, Ni and Se reacted preferentially at the ZnSe/Ni interface upon annealing at temperatures higher than 250°C. However, capacitance-voltage measurements showed that the net acceptor concentration (N_A-N_D) close to the p-ZnSe/Ni interface was reduced upon the Ni/ZnSe reaction, resulting in high contact resistance. For p-ZnSe/Au contacts, neither Au/ZnSe reaction nor reduction of the acceptor concentration were observed after annealing at temperatures lower than 300°C. This indicates that although the metal/p-ZnSe reaction is mandatory to prepare a heavily doped layer, the reaction induced an increase in the compensation donors in the p-ZnSe substrate. In order to increase the acceptor concentration in the vicinity of the p-ZnSe/metal interface through diffusion from the contact materials, Li or O which was reported to play the role of an acceptor in ZnSe was deposited with a contact metal and annealed at elevated temperatures. Ni or Ag was selected as the contact metal, because these metals were expected to enhance Li or O doping by reacting with ZnSe. However, the current density-voltage characteristics of the Li(N)/Ni and Ag(O) contacts exhibited rectifying behavior, and the contact resistances increased with increasing annealing temperature. The present results indicated that, even though the acceptor concentration in the p-ZnSe substrate increased by diffusion of the dopants from the contact elements, an increment of the compensation donors was larger than that of the acceptors. The present experiments indicated that preparation of low resistance ohmic contacts by forming a heavily doped intermediate layer between p-ZnSe and metal is extremely difficult by the DA technique.     

大庆油田南一区掺低温水集输流程

老油田开发进入高含水开采期，油井产液量、含水率大幅度增加，油井出油温度不断升高，由于降粘剂、防蜡剂的采用，防腐保温技术的进步，集输温度普遍提高。为了降低原油集输过程中的能耗，结合大庆油田南一区原油物性，地理条件和生产现状，开展了掺低温水原油集输工艺试验，取得显著的节能效果。着重介绍该区原油掺水保温流程概况，掺水温度的优选，掺低温水工艺取得的试验成果和效益。