线切割加工轧辊孔型模板提高精度的方法

详细论述了利用线切割机加轧辊孔型模板中易出现的几种影响加工精度的因素及消除方法，以达到提高模板精度。     

Si基膜片型气敏传感器微结构单元的热学性能

微结构气敏传感器由于其微型化、低功耗、易阵列化和易批量生产等优点而受到国内外研究者的广泛关注。利用微机电系统（MEMS）加工技术，制备Si基膜片型微结构单元，并分析其热学性能。这种单元工作区温度为-300℃时，加热功率约75mW；并且膜片工作区的热质量很小，温度可以于毫秒量级的时间内，在室温和450℃之间调制。利用这种微结构单元，可以在温度调制方式下，研究气敏薄膜的电学特性和敏感机理。     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

钻机柴油机的动向和190系列柴油机的发展

本文概括介绍了国内外钻机柴油机发展的水平及动向,比较了国内钻机柴油机与国外钻机柴油机在发展上的差距。重点介绍了作为国产钻机主要动力的190系列柴油机的发展状况及最新技术在该机型上的应用。     

一种新型三坐标雷达点迹提取器的设计

在目标信号检测模块的基础上增加了测有计算模块，构成一种新型的单脉冲雷达点迹提取器，显著提高了雷达系统潜在的处理能力。     

基于DELPHI的镍氢电池管理系统软件设计

通过对镍氢电池性能的研究，给出了一个应用ISA总线技术构建的、基于DELPHI编程平台的镍氢电池管理系统的设计方案，重点介绍了该系统的软件技术和实现方法。     

LMB-018A显示模块的原理及与DSP的接口

LMB-018A是深圳拓微电子有限公司推出的内含控制器和驱动器的点阵式液晶显示模块。文中介绍了该模块的原理及功能．给出了其与DSP接口的硬件电路和软件设计方法。     

缝纫设备输送动力装置的分析

文章介绍了几种缝纫设备输送动力装置的送布原理，认为应针对不同的面料特性及经制工艺要求，选用合适的设备输送系统。     

Effects of low radiation on the power quality of a distributed PV-grid connected system

We have previously investigated effects of radiation levels on power quality of a number PV-grid interactive systems in Thailand, in terms of harmonics and voltage variation at the point of common coupling (PCC). In this paper, we focus on the nature of components of complex power (actual, reactive and apparent power) of inverter output of a PV-grid interactive system due to low radiation, below 400 W/m². The system being investigated has an array of 4.2 kWp and representative of roof top units. It is observed that a PV array supplies increasing real power, in magnitude and as percentage of complex power, at high values of radiation. At low radiation level when the array does not provide enough output power, reactive power is drawn from distribution transformer and fed into an inverter and loads. Based on results from the test site and long term radiation data of Bangkok, we then estimate energy available from low radiation from a hypothetical PV-grid interactive unit in Bangkok of a similar size. It can be seen that for a tropical climate like Thailand a significant amount of energy, 20–30% of radiation energy, is in the form of reactive power. Methods must be devised to capture this low radiation energy and converted into real power form.     

Windows平台下的汉字输入法机制及应用

作者在Windows平台下，通过对E码汉字输入法系统实现的软件研发过程，本质地认识了Windows平台下的汉字输入法系统的实现原理及其基本方法；本文对Windows IME系统的两个主要组成部分：转换引擎和界面模块以及二者之间的交互关系进行了深入的分析，并揭示了Windows平台下整个汉字输入法系统的底层运转机制。