粉尘薄膜爆轰

与普通爆轰不同，粉尘薄膜爆轰波前氧化剂与燃料处于分离状态．由于激波作用下壁面燃料的注入才于壁面附近形成燃烧的粉尘云，燃烧释放的热使激波自持形成粉尘薄膜爆轰。本文在长2、8m，横截面20mm×20mm的方型水平激波管中对此类爆轰进行了实验研究．并根据作者建立的模型对其二维结构进行了数值模拟。     

薄Si膜对基底表面粗糙度的影响

利用ＺＹＧＯ光学干涉测量仪，散射积分测量法观测了光学元件表面均方根粗糙度．详细分析了薄Ｓｉ膜对基底均方根粗糙度的影响，由此认为薄膜并不总是复制基底表面的粗糙度，结果出现了薄膜降低表面粗糙度的现象．提出了一定厚度范围的薄Ｓｉ膜的表面粗糙度存在着一个稳定值的新设想．     

Mathematical modeling of falling liquid film evaporation process

A mathematical model of evaporation process from a laminar falling liquid film on a vertical plate of constant temperature is presented. The model is developed with and without interfacial shear stress due to the vapor flow at the liquid film surface. The vapor pressure drop, vapor exit velocity and cooling rate are calculated for different liquid mass flow values. It is shown that lower liquid mass flow produces higher cooling rate. The results also show that the interfacial shear stress has a considerable negative effect on the cooling rate. It is proved that there exists an optimum distance between the plates, which gives the maximum volumetric cooling rate.     

An eight‐node hybrid‐stress solid‐shell element for geometric non‐linear analysis of elastic shells

This paper presents eight‐node solid‐shell elements for geometric non‐linear analysis of elastic shells. To subdue shear, trapezoidal and thickness locking, the assumed natural strain method and an ad hoc modified generalized laminate stiffness matrix are employed. A selectively reduced integrated element is formulated with its membrane and bending shear strain components taken to be constant and equal to the ones evaluated at the element centroid. With the generalized stresses arising from the modified generalized laminate stiffness matrix assumed to be independent from the ones obtained from the displacement, an extended Hellinger–Reissner functional can be derived. By choosing the assumed generalized stresses similar to the assumed stresses of a previous solid element, a hybrid‐stress solid‐shell element is formulated. Commonly employed geometric non‐linear homogeneous and laminated shell problems are attempted and our results are close to those of other state‐of‐the‐art elements. Moreover, the hybrid‐stress element converges more readily than the selectively reduced integrated element in all benchmark problems. Copyright © 2002 John Wiley & Sons, Ltd.     

河口水流、波浪、潮流、泥沙、河床变形二维数学模型

根据河口“波浪掀沙，潮流输沙”的泥沙运动机制，引入“波浪幅射应力”反应波浪对水体和泥沙的驱动力．考虑波浪对底部泥沙作用力、波浪对水流挟沙能力的影响及风场对水流和泥沙运动的影响．同时考虑泥沙粒径大小、水体含盐度、含沙量及水流紊动程度等因素对絮凝沉速的影响．用ＡＤＩ算法求解沿水深平均方程，破开算子法解悬移质不平衡输沙方程及河床变形方程，引入通度概念处理岸滩不规则边界，建立河口水流、波浪、潮流、泥沙、河床变形二维数学模型．通过实测资料及卫星摇感图像对所建数学模型进行检验，表明它可以较好地预测河口泥沙的运动     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

空气中烧成的镍导体及其应用

将空气中烧成的镍导体用于散热制冷片制作工艺中，可降低成本，提高合格率。通过实验得到的最佳值为：镍导体中４号玻璃（ＳｉＯ２＞３０，Ｂ２Ｏ３＞１０，ＰｂＯ＜５５，ＴｉＯ２少许）的含量４．５％，化学镀镍时间５０ｍｉｎ，方阻４７．５ｍΩ／□，附着力８．１Ｎ／ｍｍ２。     

钛酸铅系薄膜的热释电性能及其应用

叙述了钛酸铅系薄膜的热释电原理，介绍了国际上近几年钛酸铅系薄膜材料、制备工艺及热释电性能，并与块状陶瓷材料进行了比较，分析表明钛酸铅系薄膜具有优良的热释电性能及可观的应用前景。     

可压缩体的滑移线场理论

从理论上建立了可压缩体的滑移线场理论，并给出了解析实例。研究表明：在平面应变条件下，可压缩体内的两族滑移线不仅不正交，而且随着平均正应力的不同而变化；可压缩体的平面应变问题可以直接采用现有的致密体的滑移线场来求出。