Phase composition and properties of solid solutions of GdFeO3–GdInO3 bulks

Solid solutions of the GdFeO₃–GdInO₃ system were prepared at 1550 °C by ceramic powder processing. The formulated composition was Gd(Fe_1−xIn_x)O₃ (GFI) with the indium contents at x = 0, 0.25, 0.5, 0.75, and 1.0. A stable phase of Gd(Fe_1/3In_2/3)O₃ in our system was identified by X-ray diffraction and phase composition analysis. Multi-phase morphologies were observed for GFI bulks with x = 0.5 and 0.75. Dielectric and electrical properties of the GFI bulks were investigated. The addition of 25% In³⁺ in GdFeO₃ had an obvious enhancement in polarization and led to an elevated resonance frequency. Dielectric properties of GFI bulks except GdInO₃ were strongly dependent upon the test frequency, which corresponded to the response of polarization mechanism. GdInO₃ displayed as a stable dielectric, which was frequency- and temperature-insensitive. GdInO₃ was thermally activated and became leaky until above 600 °C.     

Evaporation induced self-assembly of zeolite A micropatterns due to the stick-slip dynamics of contact line

In this study, a new surfactant-solvent system was described for the preparation of periodic stripe patterns of zeolite A on solid substrates. The evaporation induced self-assembly of zeolite A particles was due to the stick-slip dynamics of the three-phase contact line of the colloid solutions in acetone containing 10% (v/v) poly(dimethylsiloxane) (PDMS) fluid (2 cst.). In order to investigate the possible effects of particle size and the particle concentration on the stick-slip dynamics, three types of zeolite A samples with different particle sizes (zeolite A-I: 250-500 nm, zeolite A-II: 100-250 nm and zeolite A-III: 0-100 nm) were utilized to prepare 0.007-0.06% (w/v) colloidal dispersions. Zeolite A micropatterns were self-assembled on the surface of glass, high density polyethylene (HDPE) and poly(tetrafluoroethylene) (PTFE) substrates, which were placed vertically inside the colloid solutions and held against the wall of the cylindrical vial during the evaporation of acetone. The stripe patterns of zeolite A particles were analyzed with field emission scanning electron microscope (FE-SEM) and optical microscope. The widths of microstripes and the distance between the stripes were found as 2-20 μm and 40-60 μm respectively depending on the particle concentration. By using the stick-slip dynamics of colloids, the linear micropatterns of zeolite A nanocrystals were prepared with low cost and low energy.     

The oxidation of two ternary Ni-Cu-10 at.% Al alloys in 1 atm of pure O2 at 800-900 °C

The oxidation of the ternary alloys Ni-45Cu-10Al and Ni-30Cu-10Al has been studied at 800-900 °C under 1 atm O₂. The presence of 10 at.% Al reduces significantly the oxidation rate of the corresponding Cu-Ni alloys during the initial oxidation stages, even before the establishment of a complete Al₂O₃ layer. The weight of individual sample of the two ternary Ni-Cu-10Al alloys at 800 °C increases more rapidly than at 900 °C during the initial oxidation stage. As oxidation proceeds, the weight gain at 800 °C slows down to a degree that the total weight gain after 24 h oxidation at 800 °C is less than that at 900 °C. Due to a faster formation of the Al₂O₃ layer, which suppresses earlier the further oxidation of Cu and Ni, the external region of the scales grown on Ni-45Cu-10Al contain much less Cu and Ni oxides than those grown on Ni-30Cu-10Al. The transition from the internal oxidation to the selective external oxidation of the most reactive component Al in Ni-Cu-Al alloys is favored by higher values of the Al content, of temperature and of the Cu/Ni ratio.     

人工神经网络A／D变换器

本文对［５］的４位人工神经网络Ａ／Ｄ变换器进行了研究．指出按其方法推广实现多位Ａ／Ｄ时存在突触电阻大小以至无法实现且抗干扰能力也不好的问题并给出了解决办法．同时对如何改善神经元转移特性的硬限幅曲线作了简单讨论．     

TMS320F240片内FLASH串行口编程

本文介绍了一种对TMS320F240利用串行口进行编程的方法,此方法相对于TMS320F240研发人员普遍使用XDS510仿真器编程的方法,具有设备简单、操作方便和运行可靠等特点,尤其适合现场编程.     

The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential

Results of experiments performed to isolate the effect of surface roughness generated during slurry erosion-corrosion of 304L stainless steel are presented. Surfaces prepared by grinding to different finishes show that increasing the roughness lowers the pitting potential in chloride solution. Subsequent erosion by an aqueous sand slurry then alters this pitting potential (E_p), as measured in the solution phase alone, in a manner dependent on the initial surface roughness. Surfaces which were initially rougher show a pronounced rise in _p after erosion, while those with an initially smoother finish show a fall in E_p after erosion. Measurement of E_p during erosion-corrosion does not fit either process, with values of _Ep lower than those predicted from the surface roughness alone.     

High resolution XPS characterization of chemical functionalised MWCNTs and SWCNTs

High resolution XPS analysis of chemical functionalised multi-wall carbon nanotubes (MWCNTs) and single wall carbon nanotubes (SWCNT) was done with ESCA300 (overall instrument resolution of 0.35 eV). Information to the degree of functionalisation was ascertained by argon ion bombardment of the samples followed by XPS analysis to detect the functional groups, the percentage atomic concentration of various elements present and whether or not the detected functional groups imposed a chemical shift on the CNT atoms. The results show that true chemical functionalisation was achieved and by argon ion bombardment these functional groups can be altered relative to the C 1s carbon atoms of the CNT. The choice of chemicals used for functionalisation, the techniques employed and the types of nanotubes treated are important factors in chemical characterisation. The carbon atom on the nanotube ring to which the functional group (atom) is bonded, the chirality of the CNT, the electronegativity of the functional group, the bond type and whether the CNT is single-wall or multi-wall, or cut (short) could play a role in determining the chemical shift on the CNTs atoms. These investigations are relevant to chemical functionalisation of carbon nanotubes for various applications for example DNA sensors and other biomedical sensors.     

Etude electrochimique de differentes ilmenites

The electrochemical behaviour of several natural ilmenites has been studied by cyclic voltammetry. From the analysis of the current-voltage curves it was concluded that the valences of the metal ions in FeTiO₃ are Fe^II and Ti^IV. It was also found that little amounts of Fe^III and excess of Ti^IV (probably TiO₂) can enter into the composition of the ilmenites.     

Carbonaceous adsorbents from sewage sludge and their application in a combined activated sludge-powdered activated carbon (AS-PAC) treatment

In this study, waste biological sludge is converted to an adsorbent by chemical activation with sulphuric acid. The adsorbent obtained is then applied to the aerated vessel of an activated sludge process treating glucose and phenol to improve the quality of the treated effluent. The sludge-based carbonaceous adsorbent was found to be mesoporous in nature, with a good adsorption capacity for large molecular weight compounds and limited removal efficiency for smaller molecules such as phenol. The addition of carbon, either sludge-based or commercial, enhanced phenol removal from 58% to 98.7% and from 87% to 93% the organic matter removal as measured by the chemical oxygen demand (COD) when operated with feed concentrations of 100 mg phenol/l and 2500 mg COD/l. No differences were found between the activated sludge-activated carbon bench scale continuous reactors operating with either commercial or sludge-based adsorbents in spite of the higher adsorption capacity of the former. It is suggested that powdered adsorbent bioregeneration in the combined AS-PAC system may be impaired by the obstruction of pores due to bacterial growth, the effect being more important for the commercial activated carbon with a narrower pore size distribution.     

Flakes of natural carbyne in a diamond mine

Flakes of natural carbyne were found in Liao-Ning diamond mine, China, and examined by HRTEM, XRD and EDX. Lattice fringes and clear SAD patterns were obtained. The interlayer spacings obtained with SAD were in good agreement with those determined on the powders found in Ries crater meteorite by X-ray diffraction. However, they are different in color and shape, the one found in China being black and flaky, but the one in Ries crater meteorite being silver-white and particulate. It was assumed that carbyne might be stabilized by the intercalation of either Si or Fe in nature.