液体低温热导率的测试

介绍了非稳态法测试液体在低温下（－１００～５０℃）的热导率的测试原理、方法，测试了全氟三乙胺的低温热导率。为了提高测试的重复性，采用了相对比较法，并给出了测试装置及测试结果和误差分析。     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

Thermal Characterization of 1.3 μm InAsP/InGaAsP Ridge Waveguide MQW Lasers Based on Spectroscopy Method

An experimental way to analyze the thermal characterization of semiconductor lasers based on spectroscopy method under pulse driving conditions has been developed. By using this way the thermal characteristics of strain compensated 1.3 μm InAsP/InGaAsP ridge waveguide MQW laser diodes have been investigated. Results show that by measuring and analyzing the lasing spectra under appropriate driving parameters and temperature ranges, the thermal resistance of the laser diodes could be deduced easily. A higher thermal resistance of 640 K/W has been measured on a narrow ridge laser chip without soldering. Other thermal and spectral properties of the lasers have also been measured and discussed.     

红外热成象技术在股骨头坏死疾病针刺疗法中的应用

红外热成象技术可以有效地用于股骨头坏死疾病的诊断和针刺治疗效果的评价，效果优于其它常规方法。     

Effect of structural period and ground motion parameters on the earthquake response of asymmetric buildings

The results of a parametric study of torsional coupling effects in the response of asymmetric buildings to a grouped selection of 45 strong motion earthquakes from Europe, North America, the Middle East and Southern Pacific are presented. The period dependency of the key response parameters is studied in relation to the site dependent criteria employed by certain earthquake-resistant design codes for specifying the lateral shear forces to be resisted by the structural frames and/or walls. Unlike lateral forces, the torsional response is relatively insensitive to the ration of peak ground accelaration to velocity, which has been used in previous studies as a measure of the effect on earthquake ground motions of site soil conditions and epicentral distance. The results show that the effect of torsional coupling on edge displacement response is more pronounced in stiff, short period structures. However, the dynamic shear and torque responses are relatively insensitive to variations in structural period. Codified design provisions for torsional effects specified in the United States, Canadian and European seismic building regulations are assessed, along with alternative proposals, in relation to the analytical results. It is concluded that in some cases special provisions are needed for short period asymmetric systems, a feature which has been neglected by the codes and inadequately accounted for in previous proposals.     

半绝缘砷化镓中碳含量对热稳定性的影响

本文报导了LEC法半绝缘砷化镓单晶中含碳量对SI-GaAs热稳定性的影响。在800℃以上退火,发现当晶体中C含量大于1.5×10~(16)cm~(-3)时,SI-GaAs的热稳定性变差;而C含量小于5×10~(15)cm~(-3)时,通常表现出良好的热稳定性。     

本征吸除硅片特性研究

本文描述硅本征吸杂片的特性参数,如吸除区宽度、洁净度,氧沉淀密度、MOS电容寿命,介绍了表面态密度及残余间隙氧浓度的检测方法和工艺对参数的影响及参数之间的内在联系,文章还实验论证了不同参数水平对器件成品率的影响,建立了以MOS电容寿命为主导的参数控制方法,利用本文提供的控制参数,可使CCD-512器件成品率达60％,以上优品率≥85％。     

Interfacial Dipoles and Radiated Energy

Electric dipoles radiate an electromagnetic field into their surroundings. The electric and magnetic fields from a point source or from linear dipoles have components parallel to a spherical surface but also a radial component. In most investigations on radiated fields, only the part of the electric field that is parallel to a spherical surface is taken into account. The argument is that only that component contributes to the radiated energy. Here we show that the phase front in the lower half space is not a spherical surface and hence, the radial components contribute to radiated energy. We show differences in radiation patterns for point electric dipoles and linear dipoles, either modeled as perfectly conducting wires or as resistively loaded wires. Our primary interest lies with improving image resolution through processing of Ground-Penetrating Radar data. Here the emphasis lies with understanding the radiation characteristics of linear dipoles that can be incorporated with image processing algorithms. The model uses a thin-wire approximation for the transmitter antenna. The solution to the discrete system of equations is solved, incorporating interaction between the interface, using a CGFFT scheme including symmetrization and a newly developed preconditioning operator. We look at the electric and magnetic fields as well as the time-averaged Poynting vector radiation patterns in the E-plane and H-plane of the transmitting antenna. The results show that the radial component of the radiated electric and magnetic field is not negligible, even at distances more than seven wavelengths away from the antennas.     

Microstructural Effects of Ion Implantation on Molybdenum

The effects of ion implantation and subsequent annealing on the microstructure of molybdenum have been investigated by transmission electron microscopy. The ions investigated were carbon, nitrogen, and tellurium. The ion-induced damage was found to give rise to grain boundary migration phenomena both during implantation and during subsequent annealing. Precipitation or ordering was found to occur for each ion on annealing.     

Compact equivalent circuit model of two‐layer spiral inductors

A compact lumped‐element equivalent circuit model of two‐layer integrated spiral inductors on silicon substrates is developed in this article. Based on this proposed model, excellent agreements are achieved between the measured and simulated S‐parameters for different inductors. Also, both self‐ and mutual inductances of two‐layer inductors are accurately extracted, and their overall performances are understood clearly. © 2003 Wiley Periodicals, Inc. Int J RF and Microwave CAE 13: 148–153, 2003.