Wave dynamics on a thin-liquid film falling down a heated wall

The dynamics of a thin liquid film falling down a uniformly heated wall is studied. The model introduced by Kalliadasis et al. [J. Fluid Mech. 475 (2003) 377] for the same problem is revisited and its deficiencies, namely the prediction of a critical Reynolds number with 20% error, cured. For the energy equation a high-order Galerkin projection in terms of polynomial test functions is developed. It is shown that not only does this more refined formulation correct the critical Reynolds number, but it also gives, with an appropriate expansion close to criticality, the long-wave theory. Bifurcation diagrams for permanent solitary waves are constructed and compared with the solution branches obtained from different models. It is shown that, in all cases, the long-wave theory exhibits limit points and branch multiplicity, while the other models predict the continuing existence of solitary waves. Time-dependent computations show that the free surface and interfacial temperature approach a train of coherent structures that resemble the infinite-domain stationary solitary pulses.     

The Gas-to-Particle Heat Transfer and Hydrodynamics in Spouted Bed Drying of Sawdust

This article presents experimental results for spouted bed drying of sawdust, carried out in a full-scale as well as in a laboratory-scale dryer using air as well as steam as drying media. The aim is to present design parameters for a spouted-bed sawdust dryer that can be used by the industry in designing full-scale dryers. A hydrodynamically stable spouted jet spouted bed was obtained. The heat transfer characteristics of the bed were represented in terms of a volumetric heat transfer coefficient (VHC). When sawdust is dried in a spouted bed, the mean VHC is increasing up to fiber saturation level (20-25% wb) from 40 to 110 W/m³ K. The VHC decreases with the residence time and with an increased static bed height. Gas temperature profiles are also presented for the bottom part of the drying chamber.     

Preparation and Compressive Stress Effect of Polymer Matrix RE-Fe Giant Magnetostrictive Composite

Polymer matrix RE-Fe giant magnetostrictire composite （GMPC） was prepared using bonding and magnetic field forming technique, and magnetostriction of samples was measured for different compressive stress. The experimental results show thai there is certain compressive effect in GMPC. And the influence of compressive stress on magnetostriction of sample was investigated. It offers essential reference for application and device design of GMPC.     

解吸塔换热器706C结堵的原因分析及其对环保装置正常运行的影响

本文详细分析了解吸塔换热器结堵的原因和对环保装置正常运行的影响,并针对性地提出了防范和处理措施。     

Lean philosophy: implementation in a forging company

This research addresses the implementation of lean philosophy in a forging company with a focus on radial forging production flow lines. Here, the prime motive is to evolve and test several strategies to eliminate waste on the shop floor. In this research, a systematic approach is suggested for the implementation of lean principles. This paper describes an application of value stream mapping (VSM). Consequently, the present and future states of value stream maps are constructed to improve the production process by identifying waste and its sources. Furthermore, Taguchi’s method of design of experiments is pursued here to minimize the forging defects produced due to imperfect operating conditions. A noticeable reduction in set-up time and work-in-process (WIP) inventory level is substantiated. Finally, we conclude with a discussion of managerial implications and the future scope of research.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Real-time measurement of pointing action by using DSP

This paper presents an approach of measuring in real-time the vector of finger that is pointing to an object. DSP is used in the operation processing unit in order to do the real-time processing. The steps include the extraction of flesh-colored regions from an image, the labeling of the flesh-colored regions, and the detection of two characteristic positions on the finger so that the direction that the finger is pointing at will be calculated. The entire process takes about 29 msec, which makes it possible to have the frame rate of 34 fps. With this frame rate, this measurement approach is considered real-time and promising to be merged into other application systems. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Effect of Mineral on Metallurgical Coke Solution Loss Reaction in Blast Furnace

Thecokesolutionlossreactionisoneofthemostimportanteffectsresultingincokepulverizinginblastfurnace .Thefactorswhichaffectreactionincludecokeporestructure ,micro crystalstructureonporewall ,thecontentandconstituentofminer als ,etc .Amongthesefactors ,theconstituentofmineralsisemphasizedallovertheworldinrecentyears .Buttheemphasisofmoststudieswasputontheeffectofalkalimetals (K ,Na)oncokesolutionlossreactionandtheeffectofotherelementswassel domreported[1-5] .Theeffectofthirteenmineralsoncokesolut…     

Free-Edge and Ply Cracking Effect in Angle-Ply Laminated Composites Subjected to In-Plane Loads

This paper presents a semianalytical method for the prediction of interlaminar stresses and displacements near the free edges and ply cracks in general angle-ply laminates subjected to biaxial extensions and/or in plane shear deformation. The method is based on a state space representation of the three-dimensional equations of elasticity. Numerical solutions are obtained by using layer refinement in the through thickness direction and Fourier series expansion in the other directions. By this approach, an angle-ply laminate may be composed of an arbitrary number of monoclinic layers and each layer may have different material property and thickness. This method guarantees continuous fields of all interlaminar stresses across interfaces between material layers. Numerical results are compared with those obtained from other methods. It is found that the theory provides a satisfactory approximation to the stress singularities near the free edges and ply cracks. Numerical solutions for antisymmetric laminates under extension and general laminates under shearing are new in the literature and can be used as benchmarks for validating new models.