Size-controlled synthesis of Mo powders via hydrogen reduction of MoO2 powders with the assistance of Mo nuclei

The size-controlled preparation of Mo powders is always a challenge and important task in the molybdenum metallurgy. In the current study, Mo powders with controllable sizes are synthesized by hydrogen reduction of MoO₂ powders with the assistance of Mo nuclei in the range of 900–1100 °C. The influences of the particle sizes of Mo nuclei, the additive amount as well as reaction temperature on the morphology and particle sizes of the final products are studied. For the hydrogen reduction of MoO₂ without any additive, the obtained Mo powders always have large particle sizes. However, the addition of small amounts of nuclei in MoO₂ can help Mo nucleate dispersedly, and the growth of Mo could be also controlled by adjusting the sizes of added nuclei, amount of addition and the reaction temperature. With the addition of Mo nuclei, the different sizes of Mo powders with the good dispersity can be prepared. As adding commercial Mo powders with the particle size of about 2.03 μm, the micron-sized Mo powders ranged from 2.11 μm to 3.25 μm could be prepared. While for the case of adding ultrafine Mo nuclei of about 170 nm, Mo powders from 0.28 μm to 0.88 μm can be obtained. Moreover, the more the amounts of nuclei added and the lower the reaction temperature (in the range of 900–1100 °C) is, the smaller the particle size of the prepared Mo powder will be. The current method is a facile and feasible method, and is potential to be used for industrial production of Mo powder with controllable particle sizes.     

Effect of microstructure on the fatigue crack growth behaviour of a near-α Ti alloy

Fatigue crack growth behaviour of Ti–6Al–2Zr–1.5Mo–1.5V (VT-20 a near-α Ti alloy) was studied in lamellar, bimodal and acicular microstructural conditions. Fatigue crack growth tests at both increasing and decreasing stress intensity factor range values were performed at ambient temperature and a loading ratio of 0.3 using compact tension samples. Lamellar and acicular microstructures showed lower fatigue crack growth rates as compared to the bimodal microstructure due to the tortuous nature of cracks in the former and the cleavage of primary α in the latter. The threshold stress intensity factor range was highest for acicular microstructure.     

In situ measurements of human cough aerosol hygroscopicity

The airborne dynamics of respiratory droplets, and the transmission routes of pathogens embedded within them, are governed primarily by the diameter of the particles. These particles are composed of the fluid which lines the respiratory tract, and is primarily mucins and salts, which will interact with the atmosphere and evaporate to reach an equilibrium diameter. Measuring organic volume fraction (OVF) of cough aerosol has proved challenging due to large variability and low material volume produced after coughing. Here, the diametric hygroscopic growth factors (GF) of the cough aerosol produced by healthy participants were measured in situ using a rotating aerosol suspension chamber and a humidification tandem differential mobility analyser. Using hygroscopicity models, it was estimated that the average OVF in the evaporated cough aerosol was 0.88 ± 0.07 and the average GF at 90% relative humidity (RH) was 1.31 ± 0.03. To reach equilibrium in dry air the droplets will reduce in diameter by a factor of approximately 2.8 with an evaporation factor of 0.36 ± 0.05. Hysteresis was observed in cough aerosol at RH = ∼35% and RH = ∼65% for efflorescence and deliquescence, respectively, and may depend on the OVF. The same behaviour and GF were observed in nebulized bovine bronchoalveolar lavage fluid.     

一类两性分枝过程条件均值增长率的极限性质

本文主要研究随机环境中配对依赖人口数两性 Galton-Watson 分枝过程的条件均值增长率的极限性质．利用上可加函数的性质，得到配对单元平均增长率的极限性质和该过程条件均值的上界和下界．文中给出了关于过程条件均值增长率的两个序列，利用配对单元平均增长率的性质，获得了这两个序列的极限性质．随机环境中配对依赖人口数两性分枝过程比较复杂，本文的结论推广了现有的研究成果．     

Growth Defects in Langasite Crystals Observed with White Beam Synchrotron Radiation Topography

Langasite single crystal was grown by the Czochralski method and its perfection was assessed by white beam synchrotron radiation topography. It is found that the growth core and the growth striations are the primary growth defects and they show strong X-ray kinematical contrast in the topographs. Another typical defect in LGS crystal is dislocation. The formation mechanisms of these growth defects in LGS crystals were discussed.     

Fatigue crack propagation of multiple coplanar cracks with the coupled extended finite element/fast marching method

A numerical technique for modeling fatigue crack propagation of multiple coplanar cracks is presented. The proposed method couples the extended finite element method (X-FEM) [Int. J. Numer. Meth. Engng. 48 (11) (2000) 1549] to the fast marching method (FMM) [Level Set Methods & Fast Marching Methods: Evolving Interfaces in Computational Geometry, Fluid Mechanics, Computer Vision, and Materials Science, Cambridge University Press, Cambridge, UK, 1999]. The entire crack geometry, including one or more cracks, is represented by a single signed distance (level set) function. Merging of distinct cracks is handled naturally by the FMM with no collision detection or mesh reconstruction required. The FMM in conjunction with the Paris crack growth law is used to advance the crack front. In the X-FEM, a discontinuous function and the two-dimensional asymptotic crack-tip displacement fields are added to the finite element approximation to account for the crack using the notion of partition of unity [Comput. Meth. Appl. Mech. Engng. 139 (1996) 289]. This enables the domain to be modeled by a single fixed finite element mesh with no explicit meshing of the crack surfaces. In an earlier study [Engng. Fract. Mech. 70 (1) (2003) 29], the methodology, algorithm, and implementation for three-dimensional crack propagation of single cracks was introduced. In this paper, simulations for multiple planar cracks are presented, with crack merging and fatigue growth carried out without any user-intervention or remeshing.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

电子产品研制阶段可靠性增长试验研究

结合工程实际经验,深入讨论了可靠性增长过程及实现途径,在保持试验条件和改进过程不变的条件下,实施了对具体型号电子产品的可靠性增长试验,达到了预期的可靠性增长目标,并且利用可靠性增长试验的数学模型(AMSAA模型)来评估产品的可靠性增长,对开展可靠性增长与可靠性增长试验工作具有重要的实际意义.