Annular‐ring slot antenna designs with circular polarization radiation

The design of a microstrip‐fed annular‐ring slot antenna (ARSA) with circular polarization (CP) radiation is initially studied. To obtain CP radiation with broad 3‐dB axial ratio (AR) bandwidth that can cover the WiMAX 2.3 GHz (2305–2320 MHz, 2345–2360 MHz) and WLAN 2.4 GHz (2400–2480 MHz) bands, a novel technique of extending an inverted L‐shaped slot from the bottom section of the annular‐ring is proposed. To suppress the harmonic modes induced by the CP ARSA, the technique of integrating a defected ground structure into the annular‐ring slot is further introduced. From the measured results, 10‐dB impedance bandwidth and 3‐dB AR bandwidth of 44.86 and 9.68% were achieved by the proposed harmonic suppressed CP ARSA. Furthermore, average gain and radiation efficiency of ～4.7 dBic and 71%, respectively, were also exhibited across the bands of interest. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:337–345, 2015.     

简体接管边缘应力区局部减薄处应力特征

参考《压力容器定期检验规则》第40条,采用有限元方法计算了筒体接管边缘应力区局部减薄处的应力分布,得到了局部减薄处凹坑的尺寸与位置对应力的影响趋势,讨论了应力集中系数随尺寸变化的规律,为筒体接管边缘应力区局部减薄处的强度评定提供了一定的计算依据。     

LARGE EDDY SIMULATION OF VERTICAL JET IMPINGEMENT WITH A FREE SURFACE

1. INTRODUCTION When wastewater is discharged into rivers, lakes or oceans, it usually leads to the formulation of turbulent jet with a free surface. If the ambient water depth is shallow, the jet will impinge on the water surface and the confinement of f…     

环形截面大偏心受压构件截面延性系数计算

延性是混凝土构件的一项重要特性 ,延性系数是构件延性的度量 ,由于沿周边均匀配筋环形截面偏心受压构件受力计算的特殊性 ,至今没有一个较精确的计算公式。本文根据沿周边均匀配筋环形截面偏心受压构件的工作特点 ,采用常用应力应变关系和基本假设 ,提出了其延性系数的计算方法。     

螺旋槽管强化传热原理及在石化装置上的应用前景

详细介绍了螺旋槽管换热器的强化传热原理 ,阐明了在无相变和有相变两种工况下 ,螺旋槽管换热器的强化作用 ,并介绍了螺旋槽管换热器的设计计算方法。说明了在石油化工装置上应用的必要性     

小型中间下料预焙电解槽技术条件摆布的思考

对小型中间下料预焙电解槽技术条件摆布的原则和具体数据进行了探讨，提出了尽可能利用从大型预焙槽上得出的先进经验，并消化吸收，掌握好各种条件的平衡，以取得好经济技术指标的观点。     

斜槽电机铁心叠压胎的设计

文章介绍了一种电机铁心为斜槽的叠压胎,重点分析了叠压胎定位 斜键的设计及其公差计算。     

载金树脂硫脲硫酸解吸规律的研究

本文对硫酸和氰化钠分步解吸载金树脂上的贱金属离子，以及用硫脲硫酸溶液解吸载金树脂上的金、银络离子的解吸过程进行了研究，并通过现场采集的数据绘制了解吸曲线。     

带纵向槽筒形件拉深方法的研究

针对传境拉深带纵向槽筒形件的方法的缺点,采用一次拉深成形的方法,并通过试验和计算获得毛坯的形状和尺寸。