对水厂一期滤池技术改造后的经济评价

本文主要从经济角度分析净水厂实际生产情况及经济技术指标等方面的数据。阐述福州西区水厂一期滤池由原先双阀滤池改造成V型滤池的经济性。     

基于SOCKS协议的IPv6/IPv4转换器

介绍了IPv6协议出现和IPv6和IPv4将长期共存的必然性。讨论了从IPv4到IPv6的各种过渡机制，包括IPv4网络中IPv6域间互联的机制及IPv6节点及IPv4节点间通信的机制。实现了一个IPv6／IPv4转换器，该转换器利用了SOCKS协议和6to4隧道方式。最后分析了这个转换器的适用性和特点。     

p,V, T and derived thermodynamic data for toluene,trichloromethane, dichloromethane,acetonitrile, aniline,and n-dodecane

Experimentally determined p,V,T data are reported for toluene, trichloromethane, dichloromethane, acetonitrile, aniline, and n-dodecane at 278, 288, 298, 313, and 323 K, except for dichloromethane, for which the highest temperature was 298 K. At each temperature, measurements were done at pressures up to about 280 MPa or (for aniline and n-dodecane) at a lower pressure slightly below the freezing pressure at the temperature of measurement. Values of the isobaric expansivity isothermal compressibility and (for toluene, trichloromethane, dichloromethane, and acetonitrile) internal pressure, derived from the p,V,T data, are presented.     

Na-MMT对MCPA6／PPO原位共混体系的影响

采用水辅助分散钠基蒙脱土（Na—MMT）通过原位共混的方法制备了浇铸尼龙6（MCPA6）和聚苯醚（PP0）共混物（95／5）。通过SEM、TEM和流变等考察了非常少量的Na-MMT对共混物形貌的影响。结果发现，PP0在MCPA6基体中尺寸从几十微米下降到一个微米左右，且所有的Na-MMT都分散在MCPA6基体中。DSC分析表明PPO分散相的尺寸影响了MCPA6的结晶行为。相比于纯的MCPA6，PPO和Na-MMT的协同作用提高了纳米复合材料的强度和韧性。     

IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

雅马哈01V96V2数字调音台进阶应用指南（一）

文中从对01V96V2进行初始化、检查版本号及升级版本、校准电动推子三个方面讲解了01V96V2的进阶使用的操作方法,使读者在面对一台设置混乱或旧版本的01V96调音台时也能使用自如。     

Austenitizing treatment influence on the electrochemical corrosion behavior of 0.3C-14Cr-3Mo martensitic stainless steel

Effects of austenitizing treatment temperatures on aqueous corrosion properties of martensitic stainless steels were investigated by electrochemical tests (potentiodynamic test, potentiostatic test and electrochemical impedance spectroscopy), and surface analyses (optical microscopy and XRD). The results of potentiodynamic test revealed that the breakdown potential increased with the increased austenitizing temperature, indicating increased relative resistance to initiation of localized corrosion. EIS measurements showed that MSS3 (1030 °C) exhibits larger polarization resistance value than MSS1 (970 °C) and MSS2 (1000 °C) at passive and breakdown states. This was caused by decreasing the amount of Cr-rich M₂₃C₆ carbide which acts as preferential sites for pitting corrosion.     

兼容IPv4及IPv6的网络程序设计

介绍了在Window系统中设计兼容IPv4及IPv6的网络程序的方法,并给出了用WinsockAPI编程的具体步骤。     

Influence of Ni Interlayers on the Mechanical Properties of Ti6Al4V/(WC-Co) Friction Welds

Ni interlayers were introduced prior to dissimilar friction welding of Ti6Al4V base material to three cemented carbide substrates. The fracture strength of Ti6Al4V/(WC-6 wt% Co) welds were poor and were markedly improved when 20-µm thick Ni interlayers were introduced prior to dissimilar friction welding. These results were only produced when the (WC-6 wt% Co) cermet was electroplated prior to friction welding. When the Ti6Al4V alloy was electroplated prior to friction welding, fractured WC particles and cracking were observed in the (WC-Co) carbide substrate. The fracture strengths of Ti6Al4V/(WC-11 wt% Co) and Ti6Al4V/(WC-24 wt% Co) welds were not improved when 20-µm thick Ni interlayers were introduced prior to friction welding. During mechanical testing, the Ni layer retained at the dissimilar joint interface created a region of weakness.