rried out. The Lagrange multipliers are

boundary conditions. A cell structure which is independent to the nodes is used to evaluate the integrals of EFG     

超强吸水树脂的吸水性能研究

对自制的超强吸水树脂的吸收性能进行了研究，分别考察了吸水树脂的粒径，溶液的pH值，几种离子如Na^ ,K^ ,Ca^2 ,Mg^2 等的水溶液对吸水树脂吸收性能的影响。实验结果表明，在pH为6－8，树脂粒径为100mesh-120mesh时，树脂的吸水性能最好，各种离子对吸水树脂吸收性能的影响大小顺序为：Na^ ＜K^ ＜Mg^2 ＜Ca^2 。     

GAO Feng~1,LI Wei~2,TANG Zon

tific Experiment Center of Guangxi Medical University,Nanning 530021,China)Objective:To investigate the mutation pattern of adenomatous polyposis coli(APC),Kirsten-ras(K-ras) and p53 genes in sporadic colorectal cancer tissues.Meth     

Modeling of the bulk free radical polymerization up to high conversion—three stage polymerization model. II. Number-average molecular weight and apparent initiator efficiency

The equations for predicting the number-average molecular weight are derived on the basis of the three stage polymerization model (TSPM) in this paper. By applying the equations, a plotting approach is proposed to determine the apparent initiator efficiency defined as f[(α_td+1)/2] and the constant of chain transfer to monomer, where f is the initiator efficiency and α_td denotes the fraction of the termination rate constants by disproportionation. Using the approach to plot the experimental data in the literature, it is found that the chain transfer to monomer can be neglected for both methylmethacrylate (MMA) and styrene (St) polymerizations, but it can exert a significant effect on ethylmethacrylate (EMA) polymerization. In addition, the apparent initiator efficiency is found to be independent of reaction temperature and initiator concentration at each stage. The values of f[(α_td+1)/2] at gel effect stage are slightly reduced as compared with that at low conversion stage for MMA and EMA polymerizations. However, it decreases significantly at gel effect stage for St polymerization. Using the equations derived and the apparent initiator efficiencies obtained from TSPM plots, the number-average molecular weights at different conversions can be predicted. Comparisons show that the agreement between predictions and experimental data is satisfactory.     

浅谈造价工程师的执业能力

我国的工程造价管理体系正在逐步规范，并建立以市场形成价格为主的价格体制；改革现行工程定额管理方式，这些对造价工程师的执业能力和水平提出了更高的要求。造价工程师面临机遇、挑战，必须不断调整知识结构，提高整体素质，拓展个人在专业领域的空间。     

Analysis and Optimization Laminar Viscous Flow Through a Channel

Optimizing of laminar viscous flow through a pipe by two dimensionless values is investigated analytically. Dimensionless entropy generation and pumping power to heat transfer rate ratio are used as basis for constant viscous and the temperature dependence on the viscosity. For this matter we calculate entropy generation and pumping power for a fully developed in a pipe subjected to constant wall temperature for either constant viscosity and the variable viscosity. The variation entropy generation increase along the pipe length for viscous fluid is drawn, either the variation summation dimensionless entropy generation and the pumping power to heat transfer rate ratio are varying the fluid inlet temperature for fixed pipe length and are varying pipe length for fixed fluid inlet temperature are drawn. For low heat transfer conditions the entropy generation due to viscosity friction becomes dominant and the dependence of viscosity with the temperature becomes essentially important to be considered.     

Uptake of 226radium and 228radium by the lichen genus Umbilicaria

The 226Ra and 228Ra content of the lichens Umbilicaria cylindrica, U. deusta, U. murina and U. hirsuta has been determined as a function of the growth altitude above sea level, based on data derived from material collected from localities in southwest Poland. These data are interpreted as graphs and formulae to show the influence of environmental factors, particularly altitude, on the concentration of 226Ra and 228Ra, and the coefficients of accumulation calculated.     

攀钢转炉炼钢用碳化硅提温的试验研究

低品位碳化硅是转炉炼钢的有效提高温剂。工业性试验结果表明，碳化硅加入８．０ｋｇ／ｔ钢水提温４０．３－７０．３℃（平均４８．４℃）；渣中ＴＦｅ降低１．３％；加提温剂有利于转炉内造渣脱硫和碱少炉渣对耐火砖的侵蚀。文中还给出了攀钢转炉半钢冶炼铸用钢不水时加与不加碳化硅的ｔλ，［Ｃ］λ区域。     

车辆生产中军转民有关问题探讨

本文指出了从军用车辆生产转向民用车辆生产是一个技术与经济的过程；论述了尽快完成这一过程所必须解决的技术创新问题，生产方式问题和投资多元化问题．