SiC颗粒尺寸及含量对SiCp／2024Al复合材料性能的影响

本文对粉末冶金法制备的SiCp/2024Al复合材料的性能进行了研究。随SiC颗粒尺寸的增大,复合材料的强度降低,而塑性和磨损抗力则增加。SiC颗粒尺寸对复合材料的物理性能没有什么影响。增加SiC颗粒含量,复合材料的强度、模量均增大,磨损抗力亦明显增加,而塑性和热膨胀系数则降低。     

电解铝侧插自焙槽技术改造与环境保护

电解铝侧插自焙槽属于落后的生产工艺，由于其能耗高、物料消耗大、劳动强度大、环境污染严重，在国内电解铝中已开始进行大规模的淘汰改造。采用先进的预焙电解槽生产技术，降耗节能、改善生产劳动强度，环境污染得到有效治理，各项环境指标达标排放，经济技术指标提高，食业面貌发生了巨大大变化。     

含RE铝阳极中析出相的电化学行为研究

用电子探针和能谱分析技术，观察了Al-5Zn-0．05In-0．1Sn-1Mg-0．3RE阳极中主要析出相的成分，并熔炼了析出相合金．电位测量和腐蚀后铝阳极表面的电子探针面扫描分析表明：富Sn相为阳极相，富Fe相、富RE相为阴极相；Fe相是铝阳极自腐蚀微电池中的主要阴极相，温度对析出相的电化学行为有影响．     

介绍一种生产冲挤用铝合金坯料的新工艺

哈兹列特铝板带连铸连轧工艺已被成功地用于铝和铝合金冲击挤压用坯料的生产。在对哈氏四个有关用户扫描的基础上，列举了其产品及其用途，并介绍了相关工艺及其优点。     

铝箔轧机开卷和卷取电机的谐波分析

本文结合一台2000mm铝箔轧机的电气传动系统，介绍铝箔轧机开卷、卷取电机的谐波计算方法，并分析铝箔轧机开卷、卷取的谐波特点。     

燃气不换向蓄热式熔铝炉

蓄热式熔铝炉是一项先进节能技术，但至今在铝行业普及率不高，主要是一次性投资较大，维修费用较高。新近开发的燃气不换向蓄热式烧嘴，设备投资少、系统简化、设备故障少，使用安全可靠。     

铝电解槽修槽废渣的特性分析及处理

分析了铝电解槽修槽废渣的产生量、基本构成及污染特性，重点介绍了铝电解槽修槽废渣的处理处置方法和综合利用途径。     

激光冲击处理提高铝合金性能的研究

研究了高功率密度激光冲击处理对Ｌｙ１２ＣＺ铝合金力学性能的影响，研究结果表明激光冲击处理可大幅度提高铝合金的疲劳寿命，疲劳寿命的提高是由于微观组织中位错密度的明显增加，使得材料表层的强度和硬度也明显增加所致。     

In-situ fabrication of particulate reinforced aluminum matrix composites under high-frequency pulsed electromagnetic field

Pulsed magnetic field is generated when imposing pulse signal on high-frequency magnetic field. Distribution of the inner magnetic intensity in induction coils tends to be uniform. Furthermore oscillation and disturbance phenomena appear in the melt. In-situ Al2O3 and Al3Zr particulate reinforced aluminum matrix composites have been synthesized by direct melt reaction using Al-Zr(CO3)2 components under a foreign field. The size of reinforced particulates is 2-3 μm. They are well distributed in the matrix. Thermodynamic and kinetic analysis show that high-frequency pulsed magnetic field accelerates heat and mass transfer processes and improves the kinetic condition of in-situ fabrication.     

Effect of electrolysis superheat degree on anticorrosion performance of 5 Cu/（10NiO-NiFe2O4） cermet inert anode

5Cu/(10NiO-NiFe2O4) cermet inert anodes were prepared by cold-pressing and sintering process, and the effect of superheat degree of melting K3AlF6-Na3AlF6-AlF3 on their anticorrosion performance was studied under electrolysis conditions. The results show that, the fluctuation of cell becomes small with increasing of superheat degree, which is helpful to inhibit the formation of cathodic encrustation; the concentration of impurities from inert anode in bath goes up to certain degree, but it is far smaller than those in traditional high-temperature bath. Increasing the superheat degree of melting K3AlF6-Na3AlF6-AlF3 has unconspicuous effect on the contents of impurities in cathodic aluminum. The total mass fractions of Fe, Ni and Cu in aluminum are 15.38% and 15.09% respectively under superheat degree of 95 and 195 ℃. From micro-topography of anode used view, increasing the superheat degree can aggravate corrosion of metal Cu in inert anode, and has negative influence on electrical conductivity of electrode to some extent.