Modifizierung des ABSE‐Polycarbosilazans mit Multi‐Walled Carbon Nanotubes zur Herstellung spinnfähiger Massen

Modification of the ABSE polycarbosilazane with multi‐walled carbon nanotubes for the creation of spinable masses An inexpensive method has been found to produce ceramic SiCN‐fibres via the precursor route consisting of five processing steps: synthesis of the polymer, preparation of the spinning mass, melt‐spinning, curing via electron beam and subsequent pyrolysis at 1100 °C in a nitrogen atmosphere. A special solid and meltable fibre polymer, the so‐called polycarbosilazane ABSE, has been developed in the last decade for this purpose. Due to its low molecular weight, an adequate catalytic and thermal aftertreatment was necessary to guarantee a stable melt‐spinning process. This article discusses an alternative way to prepare a qualified spinning mass, i.e. the addition of Multi‐Walled Carbon Nanotubes (MWCNTs) to the ABSE melt. For this purpose a homogeneous dispergation of the MWCNTs in the ABSE matrix is necessary. In this study, spinning masses were fabricated in different ways. By optical analysis and comparison of the level of dispergation in these spinning masses an optimized process for integration of the MWCNTs was identified. The influence of the addition of a dispersing agent is investigated as well. In using a dispersing agent, the level of homogeneous dispersion of the MWCNTs increases whereas the interactions between the particles and the precursor melt decrease. In first spinning experiments a good spinability of the masses were noticed. Thus the addition of MWCNTs represents a new way to modify the ABSE precursor for the melt‐spinning process.     

Phase relations in the system ln-CulnS2

By DTA and x-ray diffraction the phase relations in the pseudobinary system In-CuInS₂ have been investigated. CuInS₂ hs a melting point of 1090° C and within this system there is a broad region of liquid immiscibility. A four phase invariant reaction exists at 633° C which is of the form: L₂ = L₁+ CuInS₂ + InS.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

Electron microscopic observations and DNA chain fragmentation studies on apoptosis in bone tumor cells induced by ~(153)Sm-EDTMP

ＥｌｅｃｔｒｏｎｍｉｃｒｏｓｃｏｐｉｃｏｂｓｅｒｖａｔｉｏｎｓａｎｄＤＮＡｃｈａｉｎｆｒａｇｍｅｎｔａｔｉｏｎｓｔｕｄｉｅｓｏｎａｐｏｐｔｏｓｉｓｉｎｂｏｎｅｔｕｍｏｒｃｅｌｓｉｎｄｕｃｅｄｂｙ１５３ＳｍＥＤＴＭＰＺｈｕＳｈｏｕＰｅｎｇ，Ｘｉａ...     

A simplified cascade current‐source inverter interconnected to a single‐phase three‐wire distribution system and its application to electric energy storage systems with batteries

A novel current source inverter system interconnected to the single‐phase grid is proposed. It has the same construction as the conventional three‐phase current source inverter that is interconnected to the single‐phase three‐wire distribution system. Though the proposed circuit has no output transformer, it can be equivalently performed as the single‐phase double cascade inverter by diverting the pole transformer in the utility system. By controlling the appropriate scheme, the output currents can be obtained as the five‐level waveforms and their distortions can be decreased sufficiently. It is applied to the interactive electric energy storage system with batteries and the basic discharging characteristics are discussed experimentally. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10380     

ANALYSIS OF OPEN SUN DRYING EXPERIMENTS

Open sun drying has lost its previous importance due to the fact that different factors affect its reliability and the quality of the products obtained.

One of the set-backs for the analysis of solar drying exoeriments is their deoendence on a non-controlled source of energy, i.e. solar radiation depends on climatic conditions and experiments are difficult to compare. It is thus necessary to investigate the advantages of a particular set up as well as the climatic influences. Open sun drying could constitute the natural reference, allowing the comparison of different drying strategies.

A new way of standardizing drying times, based on solar radiation inout, is proposed, to allow better evaluation of the experiments. An equivalent time is defined, allowing comparison of experiments carried out under different circumstances. Carrots and potatoes were used in these experiments.

The use of the average daily solar radiation 15.28 MJ m^-2.d^-1 in Palma de Mallorca (39.33°N, 2.37°E), is proposed for comparison purposes. An improvement of more than 12 % in the explained variance was observed, the unexplained variance being lower than 1 %.     

Authority updating: An expert authority evaluation algorithm considering post‐evaluation and power indices in social networks

In group assessment, the focus is on finding high‐authority experts to improve the reliability of assessment results. In this study, we propose an authority updating algorithm while considering the power and judgement reliability of an expert on the basis of social networks and post‐evaluations. A network power index is established and used to reflect the power of an expert while considering social networks. The measurement of the judgement reliability of an expert considers the post‐evaluation of the objects selected by experts, thereby more scientifically reflecting the reliability of experts. The analysis shows the following: although the social‐network structure influences the authority of experts, the influence weakens when the assessment group is a highly or even fully connected group; the network effect may increase the authority of some experts and reduce that of others, and it will weaken as the network connectivity increases; moreover, the judgement reliability and authority of an expert while considering post‐evaluation can encourage him/her to make fair assessments and strive to reduce his/her motivation and cognitive biases.     

Positive state‐bounding observer for positive interval continuous‐time systems with time delay

This paper is concerned with the problem of positive observer synthesis for positive systems with both interval parameter uncertainties and time delay. Conventional observers may no longer be applicable for such kind of systems due to the positivity constraint on the observers, and they only provide an estimate of the system state in an asymptotic way. A pair of positive observers with state‐bounding feature is proposed to estimate the state of positive systems at all times in this paper. A necessary and sufficient condition for the existence of desired observers is first established, and the observer matrices can be obtained easily through the solutions of a set of linear matrix inequalities (LMIs). Then, to reduce the error signal between the system state and its estimates, an iterative LMI algorithm is developed to compute the optimized state‐bounding observer matrices. Finally, a numerical example is presented to show the effectiveness and applicability of the theoretical results. Copyright © 2011 John Wiley & Sons, Ltd.     

Enabling factors toward production of nanostructured steel on an industrial scale

Utilizing the existing properties of steel, a modern technological society has been constructed. While there are over 25,000 worldwide equivalent steels based on manipulating the eutectoid transformation, there exist only a handful of commercial nanostructured steel alloys based on manipulating the more complex glass devitrification transformation. Thus, research on nanostructured steels is in its infancy, and many further developments are expected with the demonstrated promise of developing new combinations of superior properties. In this article, seven enabling metallurgical factors are presented that ultimately allow a variety of nanostructured steel products to be produced in an ever-increasing array of industrial processing techniques. Additionally, a case example of the formation of nanostructured steel are given showing how these factors can be harnessed on an industrial scale.