Optimization of abrasive water jet cutting of ductile materials

Full factorial design of experiments was developed in order to investigate the effects of jet pressure, abrasive mixing rate, cutting feed, and plate thickness upon three response variables, surface finish of cutting wear zone, percentage proportion of striation free area, and maximum width of cut. The set of sixteen experiments was performed on each of the following two ductile materials: AISI 4340 (high strength low alloy steel, hardened to 49HRc) and Aluminum 2219. Analysis of Variance (ANOVA) was performed on experimental data in order to determine the significance of effects of different parameters on the performance measures. It was found that cutting feed and thickness were highly influential parameters, while abrasive mixing rate is influential upon surface roughness only. Strong interaction was found between jet pressure and workpiece material. Multi-criteria numerical optimization was performed in order to simultaneously maximize/minimize different combinations of performance measures.     

加劲压力钢管结构优化设计

提出了改进加劲压力钢管设计的新思想,建立了加劲压力钢管结构优化设计的数学模型,介绍了约束非线性混合离散变量最优化方法的基本原理及其工程应用,研制了加劲压力钢管结构优化设计通用程序（ＯＳＤＰＲ）。结合工程实例,对加劲压力钢管进行优化设计,经济效益显著。     

Consideration on Effective Diffusivity of Strontium in Granite

Abstract

Diffusive behavior of strontium and certain kinds of divalent cations in Inada granite were studied by a through-diffusion method. In order to examine the effect of sorption onto overall diffusive behavior, two kinds of solutions were used: 0.1M KCl solution and deionized water. The effective diffusion coefficient (D_e ) and rock capacity factor (a) were (2.0–3.6) xl0–¹³ m²/s and less than 0.022 in 0.1M KCl solution and (0.32–1.7) x 10 ^?13m²/s and 1.5–2.4 in deionized water respectively. The D_e , and α in deionized water were much larger than those in 0.1M KCl solution. These results are well explained by taking into account the diffusion of sorbed ion or the surface diffusion. In support of this mechanism, most D_e , values of Sr reported for various rocks are found proportional to the sorptivity ( _ρR_d )-In the case that the sorptivity is low, D_e of Sr depends on porosity like that of nonsorbed iodide. The effective diffusion coefficient of Sr in rocks was well explained by taking into account pore and surface diffusion and was expressed as D_e=2.1 xl0^?10 _? ^1.3+3.5xl0″^?12 _ρR_d . The effective diffusion coefficient of divalent cations in the granite was found proportional to their diffusion coefficients in bulk solution.     

浅谈铝合金板带退火炉节能降耗

主要从生产组织、工艺优化、余热利用等六个方面介绍了铝及铝合金退火炉节能降耗的方法和措施.     

利用均匀设计试验进行混凝土配合比优化

提出了混凝土配合比试验的均匀设计方法,采用逐步回归法对试验数据进行回归拟合,以经济成本为目标函数,利用目标规划的方法进行混凝土配合比优化．     

露天矿生产车辆安排计划优化设计

本文结合露天矿车辆生产安排计划的特点,全面分析了车辆安排问题约束条件,构建了基于整数规划的线路车次安排数学模型。利用线性规划对电铲进行初始布点,实现对模型的合理简化,加速模型的求解。考虑到电铲利用率很难达到1,为提高模型最优解的实际应用的可行性,增加了车辆调度的弹性,设置了电铲的最大利用率。为保证电铲有一定的利用率,设置了电铲最小利用率。计算表明本模型具有较好的实用性和通用性。     

国内外环氧树脂的生产现状及应用进展

本文阐述国内外环氧树脂发展动向及应用进展。     

刨煤机的刨运速比选型

本文分析各类刨煤机在不同刨运速比下的运煤能力利用率,讨论刨运速比的最佳选择。     

Minimum-Weight Design of Multipurpose Tie-Beam of Solid Cross-Section

The paper presents the minimum-weight design of an elastic, simply-supported member of solid cross-section that is to act as a tie for a part of its design life and as a beam for the rest, but not both at any given time. Upper bounds are prescribed on the longitudinal elongation under an axial tension and on the maximum deflection under a transverse concentrated load. The range of constraints is divided into regions of possible single-purpose minimum-weight designs. The effectiveness of optimization is judged against a prismatic bar having the same transverse stiffness.     

赖氨酸高产菌株的选育

赖氨酸作为一种重要的饲料用氨基酸,需求量一直在不断增长。传统的赖氯酸生产菌株都是多年来是经过多轮随机突变和筛选得到,而近年来随着基因重组技术的发展及对生物代谢过程的了解,人们已经能够通过基因重组技术,改变代谢途径,提高赖氨酸产量。目前有不少成功将野生菌株改造为高产菌株的案例,他们都可以作为合理设计代谢途径并结合各种组学进行微生物代谢途径改造的基础。本文主要描述通过代谢途径改造并结合高通量筛选技术,快速得到赖氨酸高产菌株的方法。