钠化焙烧钒渣同时加碳氯化挥发镓的研究

考察了低温400℃和中温800℃条件下,添加活性碳及液体含碳物纸浆与钒渣、NaCl和Na_2CO_3混合焙烧时氯化挥发镓及钒转比为水溶性钒的情况。本实验得到的最高η_(Ga)为35.1％。焙烧料中不含Na_2CO_3和焙烧温度为400℃时,钒转比为水溶性钒的比率(ηv.t)较低。纸浆添加比L_(纸浆)为0.05mL/g、配料比W_(Na_2CO_3)/W_(Nacl)=2时,可望同时得到较高的η_(Ga)和(ηv.t)。     

电子聚合物基体碳纳米管复合材料研究进展

电子聚合物是一种新型的功能材料，碳纳米管具有优异的力学性能和独特的电学性能等，是聚合物基体复合材料的理想增强体，按不同电子聚合物基体类型进行了归纳，评述了电子聚合物基体碳纳米管复合材料的制备，性能和应用等情况。     

Synthesis and Hydrogen Storage in Single—walled Carbon Nanotubes

Single=walled carbon nanotubes(SWNTs) were synthesized by a hydrogen arc discharge method.A high yield of gram quantity of SWNTs per hour was achieved.Tow kinds of SWNT products:web-like substancea and thin films in large slices were obtained. Results of resonant Raman scattering measurements indicate that the SWNTs prepared have a wider diameter distribution and a larger mean diameter.Hydrogen uptake measurements of the two kinds of SWNT samples(both as prepared and pretreated) were carried out using a high pressure volumetric method,respectively.And a hydrogen storage capacity of 4 wt pct could be repeatedly achieved for the suitably pretreated SWMNTs,whicb indicates that SWNTs may be a promising hydrogen storge material.     

石油焦原料性质及炭化工艺对活性炭性能的影响

从分析石油焦原料着手，考察了其热解特性、孔隙率和石墨化程度。由于石油焦结构致密，属易石墨化碳，因此用水蒸气法直接活化得到的炭质材料吸附性能差，其碘吸附值小于350mg/g。不同来源的石油焦由于组成不同，其活化性能也有差异。通过成型法，以金山石油焦为原料轻预炭化、预氧化和炭化，得到炭化料，再用水蒸气活化得到的活性炭的碘吸附值达800.40mg/g、亚甲蓝值达120.40mg/g。以独山子石油焦为主要原料制得的活性炭的碘吸附值与亚甲蓝值分别达871．58mg/g、100..67mg/g。     

Use of TNSAC in phosphate adsorption studies and relationships. Isotherm relationships and utility in the field

There is a need for developing low cost, easily and abundantly available, yet efficient, adsorbents for the removal of phosphates during the tertiary treatment of wastewaters. The tamarind nut shell activated carbon (TNSAC) prepared on a laboratory scale has been used to evaluate its performance for phosphate adsorption. This paper describes the laboratory production of this adsorbent material in its various forms, and discusses the effects of the TNSAC process variables (the unrinsed and rinsed forms of the TNSAC and the impregnation ratio) on its performance in adsorbing phosphate. The material has been shown to be a good alternative adsorbent. As much as 95% phosphate removal by the unrinsed TNSAC is possible in about 30 min under the test conditions. The phosphate adsorbing capacity is about two times higher for the unrinsed TNSAC in comparison to the rinsed TNSAC. The adsorption rates, however, transit to extremely low rates towards the end when equilibrium conditions could be attained in about 2 h contact time. The phosphate removal mechanics are adsorption and precipitation/ion exchange when unrinsed TNSAC is used, and adsorption alone for the rinsed TNSAC. The maximum phosphate removal is found to take place at an impregnation ratio of 1.0 for both forms of the TNSAC.     

基于遗传神经网络的电站锅炉飞灰含碳量预测

针对锅炉飞灰含碳置影响因素复杂．实时测量难度大．精度低，提出了一种基于遗传神经网络的预测方法，并用于某电厂，结果表明，该方法是有效的。     

Supercritical fluid extraction of daphne (Laurus nobilis L.) seed oil

Laurus nobilis L., commonly known as daphne tree, is an evergreen that belongs to the Lauraceae family. Daphne trees produce grape-sized shiny purplish berries having three parts: flesh, skin, and an inner kernel (single seed). This study examines supercritical CO₂ (SC-CO₂) extraction of oil from daphne seeds. The oil yield of ground seeds varied from 14 to 28% depending on the method and particle size used for oil recovery. Yields were similar for both petroleum ether and SC-CO₂ extraction. The extraction yield decreased significantly with increasing particle size. The amount of extract collected increased exponentially with increasing SC-CO₂ pressure. The highest extraction yield was obtained at the highest temperature studied, 75°C. More than 45% of the oil was lauric acid. SC-CO₂ is a viable technique to obtain high-purity L. nobilis L. seed oil, which is a potential ingredient for the cosmetic industry.     

碳纳米管及其批量制备研究进展

从碳纳米管的优异性能和应用出发,综述了碳纳米管的制备方法以及我国目前在碳纳米管研究中面临的问题;分析了碳纳米管产业化对的我国纳米技术产业化发展的积极意义,特别介绍了清华-南风纳米粉体产业化工程中心开发的、具有我国自主知识产权的纳米聚团流态化技术。