利用UTD修正的MoM-PO混合算法研究

介绍了利用矩量法(MoM)和物理光学(PO)混合方法处理复杂线体结构的电磁散射问题，提出利用pulse基函数对线电流进行展开，使得处理复杂线体结构问题变得简化，并推导出一般的矩阵方程。然后针对PO在阴影区域失效等问题，利用UTD(一致性几何绕射)对该简化模型结构下的PO区域电流进行了修正，使得其应用范围得到扩展、计算精度得到提高。文中的实例结果与传统的MoM很好的一致，从而说明了该方法的有效性和精确性。     

Decomposition of Time Series Dynamic Linear Models

This paper derives the admissible decompositions for a time series dynamic linear model, assuming only that the model is observable. The decompositions depend on factorizations of the characteristic polynomial of the state evolution matrix G into relatively prime factors. This generalizes the method of West (1997 ) which considers one decomposition in the particular case where G is diagonalizable. Conditions are derived for a decomposition to be independent. These results show that no autoregressive process of order d has an independent decomposition for any integer d . Two illustrations of this procedure are discussed in detail.     

Relating the Morphology of Poly(p‐phenylene vinylene)/Methanofullerene Blends to Solar‐Cell Performance

The performance of bulk‐heterojunction solar cells based on a phase‐separated mixture of donor and acceptor materials is known to be critically dependent on the morphology of the active layer. Here we use a combination of techniques to resolve the morphology of spin cast films of poly(p‐phenylene vinylene)/methanofullerene blends in three dimensions on a nanometer scale and relate the results to the performance of the corresponding solar cells. Atomic force microscopy (AFM), transmission electron microscopy (TEM), and depth profiling using dynamic time‐of‐flight secondary ion mass spectrometry (TOF‐SIMS) clearly show that for the two materials used in this study, 1‐(3‐methoxycarbonyl)propyl‐1‐phenyl‐[6,6]‐methanofullerene (PCBM) and poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylene vinylene] (MDMO‐PPV), phase separation is not observed up to 50 wt.‐% PCBM. Nanoscale phase separation throughout the film sets in for concentrations of more than 67 wt.‐% PCBM, to give domains of rather pure PCBM in a homogenous matrix of 50:50 wt.‐% MDMO‐PPV/PCBM. Electrical characterization, under illumination and in the dark, of the corresponding photovoltaic devices revealed a strong increase of power conversion efficiency when the phase‐separated network develops, with a sharp increase of the photocurrent and fill factor between 50 and 67 wt.‐% PCBM. As the phase separation sets in, enhanced electron transport and a reduction of bimolecular charge recombination provide the conditions for improved performance. The results are interpreted in terms of a model that proposes a hierarchical build up of two cooperative interpenetrating networks at different length scales.     

Conducting composites of poly(N‐vinylcarbazole), polypyrrole,and polyaniline with 13X‐zeolite

N‐vinylcarbazole (NVC) was polymerized by 13X zeolite alone in melt (65°C) or in toluene (110°C) and a poly(N‐vinylcarbazole) (PNVC)‐13X composite was isolated. Composites of polypyrrole (PPY) and polyaniline(PANI) with 13X zeolite were prepared via polymerization of the respective monomers in the presence of dispersion of 13X zeolite in water (CuCl₂ oxidant) and in CHCl₃ (FeCl₃ oxidant) at an ambient temperature. The composites were characterized by Fourier transform infrared analyses. Scanning electron microscopic analyses of various composites indicated the formation of lumpy aggregates of irregular sizes distinct from the morphology of unmodified 13X zeolite. X‐ray diffraction analysis revealed some typical differences between the various composites, depending upon the nature of the polymer incorporated. Thermogravimetric analyses revealed the stability order as: 13X‐zeolite > polymer‐13X‐zeolite > polymer. PNVC‐13X composite was essentially a nonconductor, while PPY‐13X and PANI‐13X composites showed direct current conductivity in the order of 10^?4 S/cm in either system. However, the conductivity of PNVC‐ 13X composite could be improved to 10^?5 and 10^?6 S/cm by loading PPY and PANI, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 913–921, 2006     

Effects of thermal oxidation conditions of silicon electrodes on cathodic electrochemiluminescence of Ru(bpy)3 chelate

Hot electrons emitted from thin oxide film-coated heavily doped silicon electrodes by cathodic pulse polarization can induce electrochemiluminescence from luminophores. The intensity of electrochemiluminescence produced at the electrode surface is dependent on the features of thin oxide films formed by thermal oxidation. As a preliminary study, we investigated the effect of thermal oxide growth conditions on the intensity of electrochemiluminescence produced at these electrodes, such as oxidation atmospheres, oxidation temperature, oxidation time and pre-treatment of wafers, using ruthenium(II) tris-(2,2′-bipyridine) chelate as a model luminophore. Optimal oxidation conditions of heavily doped silicon electrodes were obtained for the generation of intense electrochemiluminescence at this kind of silicon electrodes.     

基于千兆以太网的非编网解决方案

由于在价格和兼容性上千兆以太网比FC网有明显的优势，随着计算机网络及终端技术的发展、采用千兆以太网架构非线性编辑网络正成为一种趋势。本文主要分析了采用NAS和IP SAN架构非编网络的解决方案。     

Heat transfer and flow of He II in narrow channels

Heat transfer and fluid flow of He II in a long, narrow channel connected to a bath that supplies a constant supply of heat have been investigated by numerical simulations by using the simplified model of Kitamura et al. [Cryogenics 37 (1) (1997) 1]. Such channels are used to cool compact, stable, low-temperature magnets. The fluid flow is driven by natural convection and the mutual friction between the normal fluid and the superfluid.In this model, the thermomechanical effect and the Goter-Mellink mutual friction balance each other. A consequence of this balance is that the velocity and temperature distributions of He II can be characterized by a dimensionless, dependent parameter equal to the ratio of the fluid speeds of internal convection to the total fluid flow. After a sudden application of heat flux, the internal convection dominates over the total fluid flow until the establishment of steady-state temperature gradients. This predicts that the time required to set up the steady-state total fluid flow is proportional to the total heat capacity in the channel.     

Interconnected power systems with superconducting magnetic energy storage

The objective of this work is to discuss the concept of back‐to‐back interconnection systems with energy storage, especially with a Superconducting Magnetic Energy Storage (SMES) incorporated into a back‐to‐back DC link. In this case, each converter of the back‐to‐back system is used as a power conditioning system for the SMES coils. Since the AC–DC converter can be designed independently of the frequency of the power system, a two‐way switch is connected to the AC side of each converter. This two‐way switch can select the interconnected power systems. By using the two‐way switches, this system can provide the stored energy in the SMES system to each interconnected power system through two AC–DC converters. For instance, lower‐cost power of each power network can be stored through two converters during the off‐peak hours and made available for dispatch to each power network during periods of demand peak. Then this system increases the reliability of electric power networks and enables the economical operations depending on the power demand. This paper describes the unique operations of the back‐to‐back interconnection with SMES and discuses the optimal SMES configuration for a 300‐MW‐class back‐to‐back interconnection. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(2): 37–43, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20482     

凝胶过滤色谱测定高分子量聚乙烯醇分子量和分子量分布

用凝胶过滤色谱对高分子量聚乙烯醇分子量、分子量分布进行剖析。采用Plaquagel-OH色谱柱,0.25mol/LNaNO3,0.01mol/L Na2HPO4-NaH2PO,pH=7的缓冲溶液流动相,流速1ml/min,示差折光检测器,柱温30℃,聚环氧乙烷作标准物。该方法能显著缩短分析时间,提高准确性,可用于对高聚合度聚乙烯醇进行研究和指导生产。