The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

国内外乙丙橡胶市场供需状况

介绍了国内外乙丙橡胶市场的供需状况，并对我国乙丙橡胶的产业发展提出了建议。     

液晶显示驱动电路中Fibonacci型电荷泵单元

本文中所设计的电荷泵将用于手机液晶显示驱动模块中.通过对Fibonacci型电荷泵上升时间的估算,对减小上升时间和动态功耗进行折中考虑,本文提出优化开关频率的方法.用1.2μm CMOS双阱工艺参数对所设计的电荷泵进行模拟,结果表明这个电荷泵具有较快的上升速度和较高的效率.通过提高V_GS电平和保证开关管的衬底始终接在最高电位上,文中提出了一种新型Fibonacci电荷泵,它可以正常工作在从1.2V到5V变化的多种电源电压下.     

软X射线对血液有形成分表面电荷的影响——2、淋巴细胞和血小板膜电荷的变化

软X射线不仅能引起红细胞表面电荷的变化,同时也能导致淋巴细胞和血小板表面电荷下降,表现为照射后它们的电泳率下降。低剂量范围内,这种电荷的变化是暂时性的,照后4小时降到最低点,24小时后恢复到对照的水平。细胞电泳率的下降与辐射剂量相关。淋巴细胞是一个复杂的细胞群,正常状态下,按细胞在电场中泳动速度的快慢,可分为两个组分:快峰为T细胞,慢峰为B细胞。软X射线照射以后,T和B细胞的电泳率皆减慢,频数分布峰值下降,离散度加大。血小板成分单一,电泳率较一致。 从照射浓集的血小板再加回自身血浆中电泳率的下降较照射血浆再加到血小板中的电泳率下降大得多;受照射的血小板在磷酸缓冲液中电泳率下降较在血浆悬液中严重得多;2000 rad照后,悬浮于血浆中的血小板电泳率能恢复,而悬浮于磷酸缓冲液中则不能恢复,三个方面来看,血浆中可能存在抗辐射因子。超氧化物岐化酶能有效地预防血小板电泳率的下降,从而可阻止血小板的凝聚。     

底部两层框架-抗震墙砖房抗震能力的分析方法与设计控制

提出了底部两层框架 -抗震墙砖房框剪层和砖混层的极限受剪承载力、侧移刚度、极限剪力系数计算公式 ,并基于设置不同数量抗震墙的底部两层框架 -抗震墙砖房的实例计算和弹塑性时程分析 ,给出了结构砖混过渡层与相邻框剪层的极限剪力系数比和侧移刚度比的合理取值及薄弱楼层位置判别和破坏状态评定的方法和原则。     

后压浆技术在杨凌国际会展中心基桩工程中应用效果的分析

本文叙述了杨凌国际会展中心基桩静力载荷试验的试验过程 ;通过对三根灌注桩承载力的试验结果分析 ,认为后压浆技术对提高灌注桩单桩极限承载力有很大作用     

淤泥质土状亚粘土的一些特征

珠江三角洲软土地区存在一种灰色亚粘土，其工程性能与淤泥、淤泥质土相似，但两者的物理力学性质却有明显的不同，这是一种在规范土名定义上处于过渡或边缘状态的粘性土，不是严格定义上的淤泥质土，也不是正常沉积的一般粘性土，土的强度和工程性质与淤泥质土类似，应该近沿海地区淤泥和淤泥质土对待，不应看成一般粘性土。     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Specification methods for material-handling control algorithms in flexible manufacturing systems

Good methods are needed to specify, test, and debug material-handling control logic. This article surveys a number of representative methods for defining and describing control algorithms for programmable material-handling equipment used in flexible manufacturing systems. The methods are evaluated with regard to their suitability for communication between people and as bases for interfaces to automatic program generators. It is concluded that no single method is entirely satisfactory. Three methods (position diagrams, function block diagrams, and operation networks) have potential to be combined into an effective hybrid approach that minimizes the need for the user to switch between various conceptual models.     

合成氨扩能改造中锅炉存在的问题及采取的措施

针对天脊集团年产30万t合成氨扩能改造,给2台225t/h高压锅炉带来的除氧器热量过剩、锅炉给水温度升高、主蒸汽温度降低等一系列问题,分析了产生问题的原因,从节约能源、提高锅炉效率考虑,提出了相应的解决问题的办法:利用热量分流、改造省煤器管、增加二级过热器受热面积。经过3年多的生产实践证明,取得了良好的效果。