2006年SEG年会反映的各向异性研究新进展

介绍了2006年SEG年会上所反映的各向异性研究的新进展，主要包括：提高速度分析精度的各向异性速度分析参数正交化方法；影响裂隙储层预测的地震波动力学与运动学特征差异分析；验证现行裂隙硬币理论模型可靠性的不规则裂隙有效弹性参数计算分析；提高计算效率的波场延拓各向异性参数参考值优选Lloyd算法；常见TTI介质不同成像方法试验效果的比较。     

10000m^3天然气球罐用WEL—TEN610CF钢焊接冷裂纹敏感性

WEL-TEN610CF钢是日本新日铁公司生产的低裂纹敏感性高强钢,结合我国首台国产化10 000 m3天然气球罐用37 mm厚WEL-TEN610CF钢焊接性试验研究,对该钢焊接冷裂纹敏感性进行了综合评定,为其焊接工艺的制订提供了可靠的依据。     

大型预焙铝电解槽使用碳化硅砖与普通碳砖复合块的探讨

碳化硅砖和碳化硅砖与普通碳砖复合侧块，在上世纪末期我国铝电解槽上开始推广应用。使用后各厂家普遍发现碳化硅砖及碳化硅砖与普通碳块复合侧块均出现不同程度的断裂、上抬和脱落现象，该文对断裂、上抬和脱落原因进行了分析，并提出了改进措施。     

DIN-100MnCrW4模具钢开裂原因分析

对DIN－100MnCrW4模具钢开裂原因进行了分析。结果表明，模具钢 属淬火开裂，主要原因是材料内部组织不均匀所致。     

同马大堤施工裂缝情况下的堤坡稳定性分析

 在同马大堤一标段防渗墙施工过程中，堤身出现规模不等的裂缝。介绍了堤身存在裂缝情况下，汛期水位骤降时堤防迎水坡抗滑稳定性的计算过程。重点探讨了堤坡稳定分析中工况选择、计算参数选取和强度参数敏感性分析的思路和依据。研究结果为裂缝的工程处理提供了依据。     

CO2气体保护焊在高炉炉壳焊接中的应用

通过对CO2气体保护焊在高炉炉壳组装与焊接工艺的使用，有效地控制了焊接变形及防止焊缝裂纹，阐明提高焊接质量要从多元角度出发，有机整体地考虑问题，在结论中进一步从成本，焊接质量及培训等方面分析证明推广CO2气体保护焊的必要性。     

X70管线钢在模拟土壤介质中裂纹扩展特性研究

试验研究了X70管线钢在模拟土壤介质 0 5mol/LNa2 CO3 + 1mol/LNaHCO3 溶液中和循环载荷下的裂纹扩展特性和宏观规律。结果表明 ,裂纹扩展主要受裂尖应力强度因子幅的控制。不同的应力比下 ,裂纹扩展呈现明显的门槛值特征 ,随着应力比的升高 ,裂纹扩展的门槛值降低。在碱性碳酸盐溶液 (pH =9 3)中 ,加载频率对裂纹扩展速率没有明显的影响 ;在中性碳酸盐溶液 (pH =7 0 )中 ,裂纹扩展速率随加载频率的降低而升高 ,呈现明显的频率效应。中性碳酸盐溶液中的裂纹扩展速率高于碱性碳酸盐溶液的裂纹扩展速率 ,且随加载频率的降低 ,裂纹扩展速率增大     

砖混结构现浇楼板的裂缝分析及预防措施

针对目前多层住宅采用砖混结构现浇钢筋混凝土产生裂缝的情况，分析了其产生原因，提出了预防措施。指出这些预防措施可使裂缝得到有效控制。     

Crack growth in aluminium alloy sheet material under flight-simulation loading

Crack propagation tests were carried out on 2024-T3 sheet specimens to study the effects of omitting low-amplitude cycles from the gust-dominated TWIST load sequence (MiniTWIST) and the removal of small load ranges from the manoeuvre-dominated FALSTAFF load sequence (short FALSTAFF). In other tests high-amplitude loads of TWIST and MiniTWIST were truncated at different levels. The results are compared with data from similar test programmes, including crack initiation. Attention is paid to unstationary crack growth retardation and a transient retardation during initial crack growth started by an artificial crack.     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.