An improvement to the simulation of phase-change heat-transfer during soil freezing and thawing

A new variable time step method, which is called the backwards calculating time step method, is presented in this paper. It allows numerical simulation of soil freezing and thawing while avoiding "phase change missing and overflowing". A sensitive heat capacity model is introduced through which the calculation errors are analyzed. Then the equation using the self-adjusted time step is presented and solved using finite differences. Through this equation, the time needed for a space cell to reach the phase change point temperature is calculated. Using this time allows the time step to be adjusted so that errors caused by "phase change missing and overflowing" are successfully eliminated. Above all, the obvious features of this method are an accelerated rate for adjusting the time step and simplifing the computations. An actual example proves that this method can accurately calculate the temperature fields during soil freezing and thawing. It is an improvement over traditional methods and can be widely used on com- plicated multi-dimensional phase change problems.     

强化两相混合的超临界技术制备聚乳酸微粒

针对商品化聚乳酸微球粒径分布较宽难于适用气溶胶给药要求的不足,采用水力空化混合强化超临界流体辅助雾化技术(SAA-HCM)制备聚乳酸(PLA)超细微粒.该技术主要特点是通过在超临界流体和液相进料处引入水力空化混合器,强化两相间的混合.考察SAA-HCM过程混合器压力、温度、沉淀器温度、进料中CO2与液体溶液质量流量比和溶液质量浓度等操作参数对微粒形态和粒径分布的影响,成功制备出球形度较好,粒径分布较窄(1～3μm)的PLA微球.经X射线衍射(XRD)分析和差示扫描量热(DSC)分析显示,与原料PLA相比,微球晶型及热曲线变化不大,但结晶度下降.同时把操作参数与相行为进行关联,探讨了影响颗粒形貌的机理.对比超临界流体辅助雾化法(SAA)的实验结果表明:水力空化的引入能有效强化混合器内的两相传质,混合更好,能制备出适用于气溶胶给药要求的超细微粒.     

基于VVeb2.0数字环境的本土服装品牌发展策略研究

数字化虚拟经营正成为数字化知识经济时代下创意型本土服装品牌萌芽、发展的主要手段.首先通过对本土服装品牌数字化进程的阶段性划分、归纳以及Web2.0数字化环境的综合分析,总结出本土服装品牌存在的问题;通过分析问题成因及借鉴案例,探讨应对数字化环境的策略,并设计了一套针对性较强的品牌营销方案,以期能够帮助解决一些实际问题.     

Effects of coagulation bath temperature on structure and performance of poly （vinyl butyral） hollow fiber membranes via thermally induced phase separation

Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes were investigated in detail. The morphologies of the membranes were studied by scanning electron microscopy （SEM）, the performances of water permeability, rejection, breaking strength and elongation were measured, respectively. The results indicate that all the membranes have the asymmetric morphology and the thickness of the skin layer decreases and the pore size of the outer layer increases with the increase of CBT. The permeability of membranes prepared at air gap 1.0 cm and take-up speed 0.253 m/s increases from 1.047×10-7 to 5.909×10-7 m3/（m2·s-kPa） with the CBT increasing from 20 ℃ to 40℃, and sharply increases to 35.226×10 7 m3/（m2.s.kPa）once the CBT arrives at 50 ℃. While the carbonic ink rejections have no significant decrease, totally exceed 98%, but that of acid-maleic acid copolymer greatly decreases with the increase of CBT. Both the breaking strength and elongation decrease with the increase of CBT.     

磁场中双量子位Heisenberg模型的纠缠与量子相变

以双量子位Heisenberg模型为例,讨论了磁场方向对纠缠的影响。结果表明：一定温度下,保持磁场的大小不变,仅改变其方向,不仅能获得最大纠缠,还产生了量子相变。     

Immobilizing chromium in stainless steel slags with MnO addition

This work investigates the stabilizing impact of MnO on the leaching behavior of hazardous Cr-containing CaO-SiO₂-Al₂O₃-Cr₂O₃-MnO stainless steel slags after equilibrating at various elevated temperatures and evaluates the potential immobilization of Cr into a MnCr₂O₄ spinel phase from the existing Cr₂O₃ phase. The MnCr₂O₄ spinel phase was found to be an excellent Cr-stabilizer in stainless steel slags, where the leaching tendency of potentially hazardous Cr-related ions decreased with higher MnO content and lower equilibration temperatures within the range of 0 to 15 mass pct. and 1500 to 1300°C, respectively. Thermodynamic calculations by conducting the phase stability diagram also showed that the MnCr₂O₄ spinel phase was relatively stable and the Ca₃Si₂O₇ (Ca_3-xMn_xSi₂O₇) phase was relatively unstable compared with other crystal phases in acid extractant with pH value of 3.2. Combined with the scanning electron microscopy and X-ray powder diffraction results along with the thermodynamic calculations, the leached Cr-related ions was predominantly originating from the unstable amorphous glass phase.     

PATTERN RECOGNITION APLLIED TO STABILITY OF FILLED Ti_2Ni PHASES

Pattern recognition method is used for the investigation of stability,region of filled Ti_2Niphases in multi-dimensional bond-parameter space.The filling of C,N and O atoms intoT_6 octahedra consisting of atoms of earhy-transition elements makes the expansion of thestability region of Ti_2Ni phase,and the relative stability of AI_2Cu and MoSi_2 type com-pounds decreases after the introduction of non-metallic elements such as C,N and O.     

AGING BEHAVIOUR OF PARTICULATE REINFORCED ALUMINUM ALLOY MATRIX COMPOSITES

The process of aging precipitation in SiC_p/6061 and Al_2O_3/6061 composites were investigated. Hardness testing, differential scanning calorimetry(DSC) and transmission electron microscopy were employed. Results showed that the precipitation phase form directly along dislocation lines in the composites because the particles produce high densities of dislocations which makes vacancy densities in the composites decrease, and the main precipitation phase at peak hardness was β′ phase.     

TWO KINDS OF VARIANT IN SHAPE MEMORY MATERIAL

In shape memory materials,that have been trained to have a two way shape memory effect(TWSM),themartensitic variants are classified into two groups,i.e.,preferentially oriented variants and self-accommodatingvariants.Applied stress may promote or constrain the transition of preferentially oriented variants and so changetransformation temperatures but has no essential effect on self-accommodating variants.According to the pointof view mentioned above,some experimental phenomena during thermocycling of a TWSM device may be ex-plained,such as the absence of synchronization between the plot of resistance change.temperature and the plotof memory strain vs.temperature.     

Formation and thermal stability of amorphous Ni-Mo-P alloys

The experimental researches on the chemical deposition of Ni-Mo-P amorphous alloys were carried out by adding Na2 MoO4 into acidic solutions. The optimum technology conditions were obtained by orthogonal design experiments. The structures and the relationship between compositions and their thermal stability were studied by energy spectrum (EC), scanning electron micrograph and X-ray diffraction spectrum. Compared with Ni-P amorphous alloys, the Ni-Mo-P amorphous alloys have high crystallization temperature and thermal stability, and the hardness reaches its peak when the annealing temperature is 500 ℃. With the increase of the heat treatment temperature, the surface morphology of the alloys changes.