AutoCAD图纸转换为XAML文件

利用AutoCAD插件技术,提出了一种把AutoCAD图纸转换成扩展应用程序标记语言(XAML)文件的自动化方法.通过使用ObjectArx对AutoCAD进行了二次开发,利用WPF提供的应用程序编程接口(API),把AutoCAD图纸中的图元导出成为XAML标记.实验结果表明,该方法转换出的XAML文件能够很好地保留图纸的图形信息.     

Successful fabrication of bicrystal Si substrates for YBa2Cu3O7 − y Josephson junctions

Bicrystal Si(BiSi) substrates for grain boundary (GB) Josephson junctions (GBJJs) have been fabricated by a direct bonding technique using a hot press method. The fracture strength and structure of the bonding interfaces were investigated to obtain substrates suitable for the junctions. It was found that an increase in the pressure of the hot press improves the reproducibility of the GBJJs. YBa₂Cu₃O_{7 − y} GBJJs were successfully fabricated on Bi-Si substrates with a misorientation angle of 15 ° bonded under a pressure of 90 kgf cm⁻² at 1200 °C in a vacuum of ≈10⁻³ Pa. These junctions showed typical I-V curves described by the RSJ model. The Shapiro steps induced by millimetre wave irradiation of 101 GHz were clearly observed in the I-V curves up to 3 mV, corresponding to at least 1.5 THz (, where e is the unit charge, V the voltage and h Planck's constant).     

Development of an Asymmetric Hydrophobic/Hydrophilic Ultrathin Graphene Oxide Membrane as Actuator and Conformable Patch for Heart Repair

A conductive engineered cardiac patch (ECP) can reconstruct the biomimetic regenerative microenvironment of an infarcted myocardium. Direct ink writing (DIW) and 3D printing can produce an ECP with precisely controlled microarchitectures. However, developing a printed ECP with high conductivity and flexibility for gapless attachment to conform to epicardial geometry remains a challenge. Herein, an asymmetrical DIW hydrophobic/hydrophilic membrane using heat-processed graphene oxide (GO) ink is developed. The “Masked spin coating” method is also developed that leads to a microscale GO (hydrophilic)/reduced GO (rGO, hydrophobic) physiological sensor, as well as a macroscale moisture-driven GO/rGO actuator. Depositing mussel-inspired polydopamine (PDA) coating on the one side of the DIW rGO , the ultrathin (approximately 500 nm) PDA-rGO (hydrophilic)/rGO (hydrophobic) microlattice (DrGOM) ECP is bestowed with the flexibility and moisture-responsive actuation that allows gapless attachment to the curved surface of the epicardium. Conformable DrGOM exhibits a promising therapeutic effect on rats' infarcted hearts through conductive microenvironment reconstruction and improved neovascularization.     

Ultraprecise 3D Printed Graphene Aerogel Microlattices on Tape for Micro Sensors and E-Skin

3D printed graphene aerogels hold promise for flexible sensing fields due to their flexibility, low density, conductivity, and piezo-resistivity. However, low printing accuracy/fidelity and stochastic porous networks have hindered both sensing performance and device miniaturization. Here, printable graphene oxide (GO) inks are formulated through modulating oxygen functional groups, which allows printing of self-standing 3D graphene oxide aerogel microlattice (GOAL) with an ultra-high printing resolution of 70 µm. The reduced GOAL (RGOAL) is then stuck onto the adhesive tape as a facile and large-scale strategy to adapt their functionalities into target applications. Benefiting from the printing resolution of 70 µm, RGOAL tape shows better performance and data readability when used as micro sensors and robot e-skin. By adjusting the molecular structure of GO, the research realizes regulation of rheological properties of GO hydrogel and the 3D printing of lightweight and ultra-precision RGOAL, improves the sensing accuracy of graphene aerogel electronic devices and realizes the device miniaturization, expanding the application of graphene aerogel devices to a broader field such as micro robots, which is beyond the reach of previous reports.     

Femtosecond Laser 4D Printing of Light-Driven Intelligent Micromachines

Intelligent micromachines that respond to external light stimuli have a broad range of potential applications, such as microbots, biomedicine, and adaptive optics. However, artificial light-driven intelligent micromachines with a low actuation threshold, rapid responsiveness, and designable and precise 3D transformation capability remain unachievable to date. Here, a single-material and one-step 4D printing strategy are proposed to enable the nanomanufacturing of agile and low-threshold light-driven 3D micromachines with programmable shape-morphing characteristics. The as-developed carbon nanotube-doped composite hydrogel simultaneously enhanced the light absorption, thermal conductivity, and mechanical modulus of the crosslinked network, thus significantly increasing the light sensitivity and response speed of micromachines. Moreover, the structural design and assembly of asymmetric microscale mechanical metamaterial unit cells enable the highly efficient additive nanomanufacturing of 3D shape-morphable micromachines with large dynamic modulation and spatiotemporal controllability. Using this strategy, the world's smallest artificial beating heart with programmable light-stimulus responsiveness for the cardiac cycle is successfully printed. This 4D printing method paves the way for the construction of multifunctional intelligent micromachines for bionics, drug delivery, integrated microsystems, and other fields.     

A Materials Perspective on Direct Recycling of Lithium-Ion Batteries: Principles,Challenges and Opportunities

As the dominant means of energy storage technology today, the widespread deployment of lithium-ion batteries (LIBs) would inevitably generate countless spent batteries at their end of life. From the perspectives of environmental protection and resource sustainability, recycling is a necessary strategy to manage end-of-life LIBs. Compared with traditional hydrometallurgical and pyrometallurgical recycling methods, the emerging direct recycling technology, rejuvenating spent electrode materials via a non-destructive way, has attracted rising attention due to its energy efficient processes along with increased economic return and reduced CO₂ footprint. This review investigates the state-of-the-art direct recycling technologies based on effective relithiation through solid-state, aqueous, eutectic solution and ionic liquid mediums and thoroughly discusses the underlying regeneration mechanism of each method regarding different battery chemistries. It is concluded that direct regeneration can be a more energy-efficient, cost-effective, and sustainable way to recycle spent LIBs compared with traditional approaches. Additionally, it is also identified that the direct recycling technology is still in its infancy with several fundamental and technological hurdles such as efficient separation, binder removal and electrolyte recovery. In addressing these remaining challenges, this review proposes an outlook on potential technical avenues to accelerate the development of direct recycling toward industrial applications.     

Recent Advances on High-Speed and Holographic Two-Photon Direct Laser Writing

Two-Photon Lithography, thanks to its very high sub-diffraction resolution, has become the lithographic technique par excellence in applications requiring small feature sizes and complex 3D pattering. Despite this, the fabrication times required for extended structures remain much longer than those of other competing techniques (UV mask lithography, nanoimprinting, etc.). Its low throughput prevents its wide adoption in industrial applications. To increase it, over the years different solutions have been proposed, although their usage is difficult to generalize and may be limited depending on the specific application. A promising strategy to further increase the throughput of Two-Photon Lithography, opening a concrete window for its adoption in industry, lies in its combination with holography approaches: in this way it is possible to generate dozens of foci from a single laser beam, thus parallelizing the fabrication of periodic structures, or to engineer the intensity distribution on the writing plane in a complex way, obtaining 3D microstructures with a single exposure. Here, the fundamental concepts behind high-speed Two-Photon Lithography and its combination with holography are discussed, and the literary production of recent years that exploits such techniques is reviewed, and contextualized according to the topic covered.     

In Situ Electrical Network Activation and Deactivation in Short Carbon Fiber Composites via 3D Printing

Prior studies on carbon-filler based, conductive polymer composites have mainly investigated how conductive filler morphology and concentration can tailor a material's electrical conductivity and overlooks the effects of filler alignment due to the difficulty to control and quickly quantify the filler alignment. Here, direct ink write 3D printing's unique ability is utilized to control carbon fiber alignment with a single process parameter, velocity ratio, to instantaneously activate or deactivate the electrical network in composites. Maximum electrical conductivity is achieved by randomly aligning carbon fibers that enhances the chance of direct fiber-to-fiber contact and, thus, activating the electrical network. However, aligning the fibers by increasing the velocity ratio disrupts the electrical network by minimizing fiber-to-fiber contact that resulted in a drastic decrease in electrical conductivity by as much as five orders of magnitude in both short and long carbon fiber composites. With this study, this study demonstrates that electrically conductive or insulative composites can be fabricated sequentially with a single ink. This novel ability to instantaneously control the electrical conductivity of carbon fiber reinforced composites allow to directly embed conductive pathways into designs to 3D print multifunctional composites that are capable of localized heating and self-sensing.     

Direct Freeform Laser Fabrication of 3D Conformable Electronics

3D conformable electronic devices on freeform surfaces show superior performance to the conventional, planar ones. They represent a trend of future electronics and have witnessed exponential growth in various applications. However, their potential is largely limited by a lack of sophisticated fabrication techniques. To tackle this challenge, a new direct freeform laser (DFL) fabrication method enabled by a 5-axis laser processing platform for directly fabricating 3D conformable electronics on targeted arbitrary surfaces is reported. Accordingly, representative laser-induced graphene (LIG), metals, and metal oxides are successfully fabricated as high-performance sensing and electrode materials from different material precursors on various types of substrates for applications in temperature/light/gas sensing, energy storage, and printed circuit board for circuit. Last but not the least, to demonstrate an application in smart homes, LIG-based conformable strain sensors are fabricated and distributed in designated locations of an artificial tree. The distributed sensors have the capability of monitoring the wind speed and direction with the assistance of well-trained machine-learning models. This novel process will pave a new and general route to fabricating 3D conformable electronic devices, thus creating new opportunities in robotics, biomedical sensing, structural health, environmental monitoring, and Internet of Things applications.