Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

补偿元件对载体催化元件输出特性的影响

阐述了矿井瓦斯传感器－载体催化元件在应用中，补偿元件发挥的作用和工作原理，着重分析了补偿元件对载体催化元件输出特性的影响，探讨了提高线性补偿效果的方法。     

高炉鼓风机电气控制技术改造

对高炉鼓风机事故原因分析发现，低电压保护动作、二次控制电源断电、电网电压突降是造成风机自动跳闸的主要原因。对风机电气控制技术进行改进，采取了去掉低电压跳闸保护、增设专用二次控制电源、设置瞬时断电延时自启动控制线路等措施，有效地避免了风机故障的发生，年减少经济损失66．13万元。     

基于B点磁探针膛内电枢电弧长度与速度分布测量的计算机控制系统的研究

基于B点磁探针的测量原理，建立了电磁轨道炮膛内三维等离子体电枢电弧长度和电弧运动速度测量的数学模型，通过对该模型的分析给出了用于测量膛内电枢电弧长度和运动速度分布的相应推论。开发了用于测量膛内等离子体电枢电弧长度和速度的多通道计算机控制诊断系统，并进行了相应的试验研究。     

Electrical conductivity in iodine-doped ethyl cellulose

The electrical conductivity of solution-grown ethyl cellulose (EC) films, 5–30 μm thick, has been studied in the sandwich configuration (metal–EC–metal) as a function of iodine concentration from 0.5 to 5.0 wt% ratio. The studies were conducted in the temperature range 333–383 K, while the field was varied over the range (3.0–5.5) × 10⁴V/cm. Aluminium was used as the lower electrode, while the upper electrode was of Al, Ag, Cu, Au or Sn. Certain transient effects such as a large burst of current immediately after the application of field were observed. An attempt was made to identify the nature of the current by comparing the observed dependence on electric field, electrode material and temperature with the respective characteristic features of the existing theories of electrical conduction. The results show that the electrical conduction follows Ohm's law at lower fields, while at higher fields, space-charge limited current (SCLC) was observed. It was also found that Richardson–Schottky emission was responsible, to some extent, for the transport of charge carriers in the polymer. The conductivity of the films increased on doping with iodine. The dopant molecules are considered to act as additional trapping centes and provide links between the polymer molecules in the amorphous region, thus resulting in the formation of charge transfer complexes.     

Procedures for analysis of strain transfer in the acetabular region in vitro

The failure of acetabular cups via loosening, migration or fracture is partially related to the stress distribution existing in the acetabular region. The complexity of the investigation of these stresses demands the application of a variety of model testing techniques involving combined embedded strain gauging, finite element analysis, transmission and reflective photoelasticity and crack propagation studies. The application of these procedures are described and the difficulties of obtaining representative loadings and restraints are commented upon.     

High‐Tech‐Cellulose‐Funktionspolymere nach dem ALCERU®‐Verfahren

Functional High‐Tech‐Cellulose materials by the ALCERU® process Cellulose is one of the eldest materials of mankind. While the use of cellulose in former times was focused on application as a more construction or as a more textile material at present time the application profile turns to a more functional material using the ALCERU® process. Shaping of pure cellulose dissolution in NMMNO permits the manufacturing of materials for upholstery, filtration or biodegradable film strips having an uniform cross section. Fibreds, which can be applied in several packaging materials, are available using different techniques for regeneration cellulose. A great field of innovative functional cellulose materials is opened up by addition of several functional additives to cellulose dissolution. In this way piezo‐electrical conductive cellulose fibres (PZT) or high‐temperature filtration membranes are to be generated if one adds special types of ceramic powders. Above all PZT green fibres are applied in more recent uses as sensors or actuators. Electrically conductive cellulose fibres or filaments, which can be also used in the textile chain, can be prepared adding conductive carbon black to a cellulose dope on the same way, too. Cellulose material having adapted conductivity to different application is available by adding an exact defined amount of carbon black to cellulose dissolution. Finally cellulose beads can be manufactured by means of varied shaping technique. The beads are showing variable particle sizes and narrow pore size distribution. These properties open up very interesting application in the field of human blood purification or chromatography.     

Synthesis and aqueous solution behaviors of sodium sulfonate‐terminated dendritic poly(ester‐amine)

Sodium sulfonate‐terminated dendritic poly(ester‐amine) (SPEA) was synthesized by sulfonation of acrylic double bond‐terminated dendritic poly(ester‐amine) (APEA) with sodium hydrogen sulfite (NaHSO₃) in mixture of diglycol and 2‐butanone under normal pressure. The structure of SPEA was characterized by IR, ¹H‐NMR, and elemental analysis. SPEA was water‐soluble. 1.0–40.0% (mass) SPEA aqueous solutions appeared as dilatant fluid. When pH value varied from 1.5 to 12.0, the viscosity of 1–5% (mass) SPEA aqueous solutions changed very small, and the electric conductivity almost kept stable within pH 3.0–10.0. The relationship between the viscosity and the concentration of SPEA water solutions was similar to that of NaCl water solutions. The surface tension of SPEA water solutions was lower than that of polyethylene glycol 2000 water solutions with the same concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyaniline-multiwalled carbon nanotube composites: Characterization by WAXS and TGA

Polyaniline/carboxylated multi-walled carbon nanotube (PAni/c-MWNT) nanocomposites have been synthesized by micellar aided emulsion polymerization with various c-MWNTs compositions, viz., 0.5, 1, 5, and 10 wt %. The microcrystalline parameters such as the nanocrystal size (〈N〉), lattice strain (g), interplanar distance (d_hkl), width of the crystallite size distribution, surface weighted crystal size (D_s), and volume of the ordered regions were calculated from the X-ray data by using two mathematical models, namely the Exponential distribution and Reinhold distribution methods. The effects of heat ageing on the microcrystalline parameters of the PAni/c-MWNT nanocomposites were also studied and the results are correlated. The thermal stability and electrical resistivity of the PAni/c-MWNT nanocomposites were examined with thermogravimetric analysis (TGA) and a conventional two-probe method. The TGA data indicate that the thermal stability of the nanocomposites improved after the incorporation of c-MWNTs. The influence of temperature on the resistivity of the nanocomposites was also measured. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Facial detection and location based on skin color and eye characteristic

This paper comes true a system of facial detection and location. Firstly, it realizes the facial detection of candidate region used skin color for the given image, and considers the influence of similar skin. Secondly, it realizes the location for eye region used the gray characteristic of eye and correction of central measurement, and makes further selection for facial candidate region. The end, it normalizes the facial image and makes it as front standard image, so realizes the facial characteristic location.