B737机务CBT系统建设方案的探讨

通过对AICC制订的CBT课件开发规范的探讨，阐述了CBT的基本概念和波音737飞机机务CBT的开发制作过程，以及利用Authorware开发软件制作多媒体课件的技术难点。     

公司大门工程建设施工

大门小品建筑属多项目综合性工程。本文作者从管理者的角度 ,通过对公司大门及附属工程施工质量控制的总结 ,说明了质量控制应贯穿于工程施工的全过程     

我国聚甲醛工业的供需分析

从国内聚甲醛树脂的生产、贸易及消费状况出发 ,分析了国内聚甲醛工业的供需现状并提出短期预测。     

Practical method for generation expansion planning based on dynamic programming

This paper presents an efficient method which provides the optimal generation mix and the optimal generation construction process. The approximation method in which the dynamic programming technique and gradient method are combined is applied to determine the optimal generation mix with hydropower generation technologies. The successive approximations dynamic programming (SADP) technique, which is very suitable for high-dimensional multistage decision process problems, is used for obtaining the optimal generation construction process. The effectiveness and feasibility of the developed technique are demonstrated on a practical power system model which has five types of generation technologies including a hydropower generation technology.     

Community OR — Five Years of Organised Activities and Beyond

What has become known as Community Operational Research has been around in the UK for many years. The election of Jonathan Rosenhead as President of the UK OR Society in 1986–87 was the catalyst for bringing together and expanding activities which had been carried out largely by individuals working in isolation on a voluntary basis. The following five years have seen the establishment of the Community OR Unit at Northern College, the Centre for Community OR at Hull University and the Community OR Network, which supports the activities of volunteer OR workers across the UK. This paper reviews the range and types of work which have been undertaken by various practitioners. An assessment of the success of community OR is made and a number of issues which have arisen are discussed. Finally, given the diverse nature of community OR, its practice and practitioners, there is some discussion about the future of the area.     

超薄SiO2层的热生长

隧道小孔中超薄ＳｉＯ２的生长是ＥＥＰＲＯＭ电路制造的关键工艺之一。采用ＳＵＰＲＥＭ－Ⅲ工艺模拟程序对超薄ＳｉＯ２的热生长进行了工艺模拟，经过大量的工艺实验及优化，确定了超薄ＳｉＯ２的最佳生长条件，生长出的ＳｉＯ２性能良好，完全可满足ＥＥＰＲＯＭ研制的要求。     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

压水堆核燃料循环的经济分析程序介绍

所开发的压水堆核燃料循环分析计算机经济程序包括12个子程序,代表着压水堆整个核燃料循环各种不同的工艺过程。本程序能算出压水堆核电站核燃料循环中燃料费用对发电成本的影响,给出各工艺过程对燃料成本的敏感度分析,并尽可能给出燃料循环中燃料材料及服务的价格数据.     

New Engineered Particles from Spray Dryers: Research Needs in Spray Drying

This article reviews developments in the simulations of spray dryer behavior, including the challenges in modeling the complex flow patterns inside the equipment, which are often highly transient and three-dimensional in nature. There appears to be considerable scope for using CFD simulations for investigating methods to reduce the rates of wall deposition and of thermal degradation for particles by modifying the air flow patterns in the chamber through small changes in the air inlet geometry. Challenges include building particle drying kinetics and reaction processes, as well as agglomeration behavior, into these simulations. The numerical simulations should be valuable supplements to pilot-scale testing, enabling more extensive and accurate optimization to be carried out than hitherto possible. New understanding of reaction processes and materials science, in combination with recent knowledge of the application of CFD to these problems, may enable new engineered powder products to be developed from the one-step spray-drying process.