Development of catalysts for hydrogen generation from hydride compounds

Catalytic hydrolysis of NaBH₄ and NH₃BH₃ has been studied. It was shown that the nature of the support and the active component of the catalyst affect the H₂ generation rate. Despite similar sizes of rhodium particles formed on the surface of different supports (γ-Al₂O₃, TiO₂, carbon), their reactivity is different. Rh/TiO₂ with low rhodium concentration (1 wt.%) is the most active catalyst both in the hydrolysis of NaBH₄ and NH₃BH₃. The obtained results show that the rhodium chloride interaction with titania determines the reactivity of rhodium particles formed under action of NaBH₄ medium. TEM, DRS UV–vis and XPS were used to characterize the catalysts.     

低应变动测与抽芯验桩结果对比分析

通过低应变反射波法与钻孔抽芯 2种检测方法的结果对比分析 ,验证低应变反射波法检测基桩的缺陷及位置的准确性 ,积累波形判别的经验。     

低渗透油田合理注采井距的确定--以纯41块沙4段低渗透油田为例

以纯41块沙4段低渗透油田为例，从低渗透油田渗流机理出发，分析了造成低渗透油田开发效果差的主要原因。在计算注水井最大井底流压、油井最小井底流压、油水井之间可建立的最大注采压差的基础上，结合室内试验确定的最小启动压力梯度公式计算油田技术极限注采井距，并结合经济合理井距计算结果，确定了油田合理注采井距，并提出了下二步调整方案，实施后取得了显著的效果。该方法为低渗透油田合理井距的确定、提高低渗透油田的开发效果提供了理论依据。     

裂缝各向异性介质中P-SV转换波正演模拟

裂缝介质正演是研究裂缝性油藏的各向异性、裂缝检测方法、裂缝AVO反演等的前提。在裂缝方位各向异性(EDA)介质模型的基础上，重点研究了纵波震源激发的地震波所产生P-SV波的有限差分正演模拟方法。从各向异性单斜对称系统的刚性矩阵推导出的波动方程，可以满足EDA介质模型不同方位角入射的二维差分模拟要求。在有限差分模拟中，采用了普通的Kelly差分格式、二阶各向异性吸收边界条件和一般的纵波震源的解析形式，并应用修正的通量传输校(FCT)方法来消除频散。同时，对纵波震源的解析式进行了技术处理，取得了较好的效果。     

3G系统的安全策略分析

介绍了当前3G系统面临的各种威胁和针对3G的攻击方法,如对非授权数据的非法获取、对数据完整性的攻击和对业务的非法访问攻击等.分析了3G系统的安全体系结构和安全特性的优缺点.     

Effects of low radiation on the power quality of a distributed PV-grid connected system

We have previously investigated effects of radiation levels on power quality of a number PV-grid interactive systems in Thailand, in terms of harmonics and voltage variation at the point of common coupling (PCC). In this paper, we focus on the nature of components of complex power (actual, reactive and apparent power) of inverter output of a PV-grid interactive system due to low radiation, below 400 W/m². The system being investigated has an array of 4.2 kWp and representative of roof top units. It is observed that a PV array supplies increasing real power, in magnitude and as percentage of complex power, at high values of radiation. At low radiation level when the array does not provide enough output power, reactive power is drawn from distribution transformer and fed into an inverter and loads. Based on results from the test site and long term radiation data of Bangkok, we then estimate energy available from low radiation from a hypothetical PV-grid interactive unit in Bangkok of a similar size. It can be seen that for a tropical climate like Thailand a significant amount of energy, 20–30% of radiation energy, is in the form of reactive power. Methods must be devised to capture this low radiation energy and converted into real power form.     

美国危险废物处理的领先尖端技术--等离子强化熔炉介绍

从工作原理、主体结构、工艺流程等方面，系统地介绍了当代处理危险废弃物的领先尖端技术——等离子强化熔炉，并结合实地考察，介绍了其工业化发展及其应用实例。     

Automating application software generation

Many approaches have been proposed to enhance software productivity and reliability. These approaches typically fall into three categories: the engineering approach, the formal approach and the knowledge-based approach. But the optimal gain in software productivity cannot be obtained if one relies on only one of these approaches. This paper describes the work in knowledge-based software engineering conducted by the authors for the past 10 years. The final goal of the research is to develop a paradigm for software engineering which integrates the three approaches mentioned above. A knowledge-based tool which can support the whole process of software development is provided in this paper.     

空调器中多翼离心风机的噪声研究及结构优化

采用逐步回归法对大量的多翼离心风机实验数据进行拟合,针对家用空调行业中以噪声为其最重要 的考核标准,得出了噪声与叶轮结构参数及风机性能参数间的近似关系式,并以噪声为目标函数进行了优化计算。     

Triple tangent flank milling of ruled surfaces

This paper presents a positioning strategy for flank milling ruled surfaces. It is a modification of a positioning method developed by Bedi et al. [Comput Aided Des 35 (2003) 293]. A cylindrical cutting tool is initially positioned tangential to the two boundary curves on a ruled surface. Optimization is used to move these tangential points to different curves on the ruled surface to reduce the error. A second optimization step is used to additionally make the tool tangent to a rule line, further reducing the error and resulting in a tool position, where the tool is positioned tangential to two guiding rails and one rule line. The resulting surface has 88% less under cutting than the method of Bedi et al.