丙烯高温氯化法生产环氧氯丙烷技术分析

由于环氧树脂、合成甘油等产品需求强劲。促使国内环氧氯丙烷需求量的快速增长。但国内的生产能力和产量远不能满足实际需要.需大量进口。丙烯合成环氧氯丙烷技术成熟、原料供应充足、投资不算太大、利润率较高.能使投资者得到较满意的回报。     

Influence of the temperature profile in the interface on the bond strength of polyamide–polyurethane two‐component tensile bars

Two‐component tensile bars with polyamide 6 (PA) and thermoplastic polyurethane (TPU) unmodified and modified with 4,4′‐diphenylmethane diisocyanate (MDI) have been investigated. It is known that the bond strength of PA/TPU tensile bars can increase by about 50% if MDI‐modified polyurethane is applied. The subject of these studies is the analysis of the influence of the mass temperatures on the bond strength. The mass temperatures of the first and second injection process and the delay time between the first and second injection processes determine the temperature gradient in the interface at the moment of the second injection. There is an increase in the bond strength when there is an increasing temperature gradient; therefore, the mass temperature of the first component at the delay time has to be lower than the mass temperature of the second component. The temperature gradient can be used as a measure of the thermal annealing of the first component near the interface during the heat transfer from the second component. It can be concluded that effective thermal annealing causes an increase in the bond strength. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4297–4305, 2006     

Microstructure evolution of nanostructured Ni3Al during annealing

A nanocrystalline layer was produced on the surface of Ni3Al intermetallic by means of surface mechanical attrition treatment. The surface nanocrystallites were annealed at 250-750 ℃ for 30 min. Microstructure evolution of nanocrystallites during annealing was studied by X-ray diffraction （XRD） and transmission electronic microscope （TEM）. The experimental results show that long-rang order recovers rapidly when annealing temperature is below 250℃ and changes slowly at 350-550 ℃, and then it increases rapidly at 750℃. The grain size of nanocrystallites of Ni3Al keeps stable and crystal defects recover when they are annealed below 550℃. The grains grow normally in low temperature annealing and abnormal growth occurs at 750℃.     

颗粒增强TiAl基复合材料及其Si的韧化作用研究EI

运用ＸＤ工艺制备了颗粒增强ＴｉＡｌ基复合材料。增强颗粒均匀分布于ＴｉＡｌ基体中并细化ＴｉＡｌ合金。通过在ＴｉＢ_２／ＴｉＡｌ、ＴｉＣ／ＴｉＡｌ复合材料中加入适量的Ｓｉ，颗粒增强ＴｉＡｌ基复合材料的室温延性得到了改善。     

武钢含铁化合物二次资源综合利用的有效途径

在分析武钢含铁化合物二资资源的种类、数量和理化特性的基础上,提出了这部分资源的产品开发方向,并根据这些开发产品国内外市场的分析,指出这种开发将可能取得可观的经济效益。简介了这类开发的工艺和设备。     

钛酸酯催化环氧树脂固化动力学研究

用FTIR“原位”技术,研究了钛酸酯(Tc-114)偶联剂对环氧E-44和二氨基二苯基甲烷(DDM)固化反应的催化作用,得出固化程度与时间的关系曲线。又根据DSC曲线,分别算出加有Tc-114和不加Tc-114的两个固化体系的反应表观活化能和反应级数。结果表明,Tc-114的存在使环氧固化反应活化能降低,催化作用明显。     

Advances in titanium metal injection molding

The approaches to production of titanium powder injection molded parts are reviewed. Historically, oxygen levels have been too high for structural use (particularly with the Ti-6Al-4V alloy). However, recent advances in starting powders, binders and sintering facilities now allow oxygen levels in the Ti-6Al-4V alloy to be controlled to about 0.2 wt.% oxygen. This should result in significant expansion of the titanium PIM market place into aerospace, automobiles, surgical instruments, dentistry, communication devices (such as computers and cell phones), knives and guns. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 5–6 (455), pp. 118–125, 2007.     

附加在车床上的疲劳裂纹装置

本文介绍一种作者自己设计的疲劳裂纹装置．它可以代替价格昂贵的高频疲劳试验机；用于对三点弯曲试件预制疲劳裂纹．该装置结构简单，容易制造．投资少，附加在车床上即可工作．     

异型材挤出口模内的流动模拟

本文根据挤出机理，对口模内的流动行为进行适当的简化和假定，建立了挤出口模内流动分析的数学模型，并采用横截面／假想区域法实现了复杂异型材挤出口模内的数值模拟，数值分析结果与三维有限元解和解析解的对比，取得了满意的效果。     

球状碳单质分子的发现,研究现状及应用前景

综述了碳的第三种同素异形体──球状碳单质分子的发现、结构、性质及其应用前景。