Preparation of Compound Ultrafine CeO2 by Wet-Solid-Phase Mechanochemical Modification

To satisfy practical requirements from industrial applications, an alternate route for synthesis compound ultrafine CeO2 powders by wet-solid-phase mechanochemical modification using industrial grade hydrated cerium carbonate as raw material was proposed.The effect of modifier reaction percentage, reaction time, calcining temperature and modifier amount on particle size, density, suspensibility, and hardness of compound CeO2 powder was investigated.The phase evolutions of preparation process were characterized by XRD.SEM micrograph of the final product shows that compound CeO2 powders obtained are well-dispersed, spherically-shaped, uniformly-sized and submicron-sized particles.The method is readily available in raw material, low in cost, simple in process, and has great potential for industrialization.The compound CeO2 powders of different physical properties can be synthesized by controlling the above-mentioned influence factors in preparation process.     

不同磁场作用对AZ31镁合金的凝固组织的影响

镁合金是具有优越性能的金属材料,镁合金的加工是目前国内外正在深入进行研究的新课题.实验发现在镁合金的凝固过程中施加低频或静态磁场都能细化晶粒,但静磁场得到的细化效果要优于低频交流磁场,同时随磁感应强度的增加,静磁场细化晶粒的效果明显提高;在静磁场条件下晶界共晶体组织的厚度明显减小,同时在晶内出现了大量细小块状化合物,这有利于改善镁合金的综合性能.     

W-Ni-Cu高比重合金注射成形烧结收缩及性能的研究

研究了W-Ni-Cu高比重合金注射成形工艺过程收缩率和性能。比较了模具尺寸、注射坯尺寸、烧结坯尺寸，及烧结阶段各方向收缩率的关系，发现实际收缩与理论预测收缩率较为一致，但在厚度方向存在与其他方向收缩不一致的情形，这与由重力作用产生的塑料流动有关；还探讨了烧结坯密度与烧结条件的关系，测定了烧结坯的力学性能及断口形貌、金相组织，烧结坯在1400℃，90min烧结达到了99％的相对密度，断裂强度600MPa以上。     

Palogue油田复合油藏动态响应及特征描述

以简单的复合油藏模型理论和方法为基础,以Palogue油田的实际测试井为例,介绍了复合油藏模型的试井动态识别与模型拟合,及与地质静态资料相结合的油藏综合描述过程.该描述方法将会对实际试井解释和油藏综合描述工作有所借鉴和帮助.     

用环氧厚浆涂料防混凝土碳化

介绍了针对早期建筑的混凝土桥梁碳化情况采用H52-S4环氧厚浆涂料进行封闭保护、防腐处理的施工方法及施工工艺，并提出施工中应注意的有关事项，对温度影响、表面气泡处理进行了讨论，提出合理化建议。     

环氧基的PCB对无铅组装的兼容性

综述了环氧树脂基的PCB与无铅化组装的兼容性问题。经过大量试验表明,常规的FR-4基材和双氰胺固化的高Tg基材是不能满足无铅化组装要求的,而采用酚醛固化的中等-Tg的环氧树脂基材是可能成为无铅化组装用基材的。同时,PCB制造过程也起着重要的作用。PCB设计和再(回)流焊的加热梯度也影响着无铅化的性能。     

咪唑封端扩链脲改性环氧树脂E-51/酸酐MTHPA体系性能研究

以端羟基聚环氧丙烷1000，甲苯二异氰酸酯（TDI），2－甲基咪唑为原料，合成了扩链脲TI，利用DSC，动态热机械分析仪DMA，冲击试验机及扫描电镜（SEM）等手段对TI改性的环氧树脂E－51／甲基四氢化邻苯二甲酸酐（MTHPA）固化体系的反应活性，动态力学行为，冲击性能，断裂面形态结构进行了系统研究，结果表明，改性后的E－51／MTHPA体系反应活性明显提高，固化反应峰顶温度较未改性体系降低160℃－200℃，固化反应的表观活化能由未改性体系的160．3kJ/mol降至63kJ/mol-87kJ/mol，同时与未改性体系相比，经过改性的环氧树脂固化体系冲击强度有较大的提高，在TI含量为5％时体系的玻璃化转变温度Ts达到最高，各改性体系冲击断面呈韧性断裂。     

Numerical Filling Simulation of Injection Molding Using Three-Dimensional Model

1 Introduction During injection moulding, the rheological response of polymer melts is generally non-Newtonian and nonisothermal with the position of the moving flow front. Because of these inherent factors, it is difficult to analyze the filling process. Therefore, simplifications usually are used. For example, in middle-plane technique and dual domain technique [1], because the most injection molded parts have the characteristic of being thin but generally of complex shape, the Hele-Shaw …     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

计算机控制的SEESR实验系统的研制

SEESR(Simultaneous Electrochemical ESR)是研究电极过程中的自由基中间体行为的理想和方便的手段。在以前研制的ESR仪数据系统的基础上,我们应用IBM-PC/XT微机与JES-FE1XG型(JEOL产)ESR谱仪及HDV-7型恒电位仪研制了一套由计算机控制的SEESR实验装置。该系统可以完成包括循环伏安法、电流阶跃、电位阶跃及电位反转等多种电化学方法的SEESR实验。系统还具有包括数据平滑、曲线拟合等功能的多种数据处理软件,使用方便。我们应用模型化合物对该系统进行了实际测量,所得结果与文献报道一致。