高压旋喷桩复合地基承载特性的有限元分析

结合工程实际,运用大型有限元分析软件ANSYS分析了不同桩长、不同桩土模量比和不同桩间距情况下高压旋喷桩复合地基的承载特性.结果表明,该地基存在有效桩长,当桩土模量较合适时,该地基能够发挥最大作用;同时运用ANSYS优化功能,得出了最优桩长、最优桩体弹性模量和最优桩间距,为实际工程提供一些参考.     

静压挤密桩在湿险性黄土地基处理中的应用

为了解决水泥土挤密桩施工过程中噪音过大的问题,提出了地基处理的静压挤密桩施工法,并结合工程实际测试了静压挤密桩在湿险性黄土地基处理中应用的效果.测试结果表明,该方法在施工时噪音较小,施工速度高,满足设计要求,此为该地基处理方法的应用和推广提供了依据.     

FEM analyses for influences of stress corrosion and pressure solution on THM coupling in dual-porosity rock mass

With the models of stress corrosion and pressure solution, by Yasuhara et al., two computation conditions were designed for a hypothetical nuclear waste repository in an unsaturated dual-porosity rock mass: (i) the fracture apertures are changed with the stress corrosion and pressure solution (the porosity of rock matrix is also a function of stress); (ii) the fracture apertures and the porosity of rock matrix are constants. Then the corresponding two-dimensional FEM analyses for the coupled thermohydro-mec...     

沸腾两相流动压力波动信号的特性

研究了竖直管内沸腾两相流动时压力波动信号的特性,对压力波动时间序列进行了标准偏差分析、功率谱密度函数分析、分维数分析、相关维分析及Kolmogorov熵分析,考察了热流密度对压力波动的影响规律.结果表明沸腾两相流动具有非线性混沌特性,且热流密度对各特征参数有不同影响.     

On the oxidation kinetics and mechanisms of various SiC-coated carbon-carbon composites

SiC coatings on the surface of C-C were produced by either silicone resin impregnation/ pyrolysis or reaction sintering. Cycles of resin impregnation/pyrolysis produced an SiC coating, on the walls of fine open pores, which was effective in reducing the oxidation rate of C-C and in shifting the transition temperature to a higher value. Unless it is pre-coated with a pyrocarbon layer before sintering, plain reaction sintered SiC has oxidation behaviors similar to those of the above-mentioned SiC. The dense pyrocarbon film deposition on the surface of C-C could form a better SiC film than others. The carbon film homogenized the surface of C-C and a dense SiC film was established. The oxidation of the coated C-C can be modelled by a set of “oxidation resistors” in series and/or in parallel, with each resistor corresponding to an oxidation element. The controlling mechanism can be resolved from the activation energy. A combined resistant layer, consisting of resin impregnation, pyrocarbon film and reaction sintering SiC, showed the best oxidation resistance of any single-layer coated C-C composite.     

Calculation of single adsorption isotherms from gravimetrically measured binary gas mixture adsorption isotherms on activated carbon at high pressures

A method is developed for the calculation of single-component adsorption isotherms from gravimetrically measured binary gas mixture adsorption isotherms at high pressures, at two temperatures and for different mole fractions of the gas phase. The adsorption of nitrogen/methane on active carbon Norit R1 is taken as an experimental example.     

Probabilistic and interval reliability design of the composite pressure vessel

Considering the randomness or interval character of physical parameters and applied loads of composite pressure vessels (COPV), the COPV reliability-analyzing model is built. And then the computational expressions for the mean value, standard deviation and deviation of fiber stress are deduced by the random factor method. The probabilistic and interval reliability designs on COPV are implemented by utilizing the probabilistic method and interval method combined with the improved particle swarm optimization (PSO) algorithm, respectively. The influence of fluctuation of structure uncertain parameters on COPV design thickness is inspected. Finally, examples are given to demonstrate that both probabilistic and interval reliability methods can satisfy the safety requirement and both are of higher rationality than the traditional safety factor method. And probabilistic method has a lower relative error but a higher computational complexity contrasted with the interval method.     

Intergranular oxidation of silicon in 20Cr-25Ni niobium-stabilized stainless steel at 1140–1230 K

The kinetics of intergranular oxidation of silicon in a 20Cr-25Ni Nb-stabilized stainless steel are reported, at temperatures in the range 1140–1230 K, in CO₂ at 40 bar pressure. The depth of attack increased parabolically with respect to time, with an activation energy of 335±30 kJ/mol. The mechanism of growth is discussed in terms of classical internal-oxidation theories, and an alternative explanation based on an available-space theory is developed. The internal oxidation rates in a number of different alloys are compared with diffusivities of metals in the base alloy. It is proposed that intergranular oxidation in the 20–25 Nb steel is controlled by the rate of outward diffusion of iron or chromium in the alloy.     

Evolution of insoluble eutectic Si particles in anodic oxidation films during adipic-sulfuric acid anodizing processes of ZL114A aluminum alloys

The effects of insoluble eutectic Si particles on the growth of anodic oxide films on ZL114A aluminum alloy substrates were in-vestigated by optical microscopy (OM) and scanning electron microscopy (SE...     

Deformation transition of intact coal induced by gas injection

Gas migration in coal bed is a multiple-physical process, of which not only includes gas desorption/diffusion through coal matrix and gas Darcy flow through the cleat system, but also results in deform...