CALCULATION OF TRANSFORMATION VOLUME FRACTION TO HQ590 HOT ROLLED STRIP STEEL DURING CONTINUOUS COOLING

On the basis of phase transformation kinetics, the transformation of γ→α,P,B have been investigated through considering the effect of deformation. The calculation methods of volume fraction have also been given. Comparing with common method, the simulated results are in more agreement with experiment results.     

深冲汽车簿钢板织构的表述方法

利用晶体学性质,将深冲汽车薄板的两种主要特征织构表述于反极图之中,再利用织构定量技术便能简捷地分析深冲钢板的织构与深冲性能的关系。经验证,此法与ODF定量分析所得的结果一致。     

Fatigue crack growth resistance of SiC<Subscript>p</Subscript> reinforced Al alloys: Effects of particle size,particle volume fraction,and matrix strength

The main aim of this work was to study the effects of particle size, particle volume fraction, and matrix strength on the long fatigue crack growth resistance of two different grades of Al alloys (Al2124-T1 and Al6061-T1) reinforced with SiC particles. Basically, it was found that an increase in particle volume fraction and particle size increases the fatigue crack growth resistance at near threshold and Paris regimen, with matrix strength having a smaller effect. Near final failure, the stronger and more brittle composites are affected more by static modes of failure as the applied maximum stress intensity factor (K _max) approaches mode I plane strain fracture toughness (K _IC).     

Al-Si-Mg三元合金的溶质分凝及其对凝固过程的影响

从热力学角度分析了三元合金凝固过程中的溶质分凝行为, 利用耦合热力学计算技术研究了Al-Si-Mg三元合金溶质分凝因数在凝固过程中的变化规律, 获得了其与固相体积分数的定量关系, 进而预测了不同条件下Al-Si-Mg三元合金的凝固过程和相析出规律. 实验发现三元合金中溶质分凝因数在凝固过程变化巨大, 采用二元系中的参数使得对共晶种类和共晶分数的预测均与实验值有较大偏差. 采用耦合热力学计算技术, 获得了分凝因数在凝固过程中的变化规律, 使预测值更好地吻合于实验结果.     

Miniemulsion and conventional emulsion copolymerization of styrene and butadiene: Effect of process on gel content

The properties of styrene/butadiene copolymers obtained by conventional emulsion and miniemulsion polymerizations were studied. Thin layer chromatography with flame ionization detection was used to determine the gel fraction of the copolymer in the latex particles as a function of conversion. It was found that the gel formation began at a higher conversion in the miniemulsion polymerization when compared with that in the conventional process. Also, a lower glass transition temperature was noted at the lowest conversion sampled (～25%), implying a higher initial butadiene monomer concentration within the nucleated miniemulsion monomer droplets when compared with particles formed conventionally. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4616–4622, 2006     

过氧化物交联聚乙烯的力学性能研究

采用过氧化物交联方法研究了交联聚乙烯的工艺、配方和性能，探讨了过氧化物用量对材料力学性能及凝胶含量的影响，以及炭黑、氧化锌、抗氧剂对材料性能的影响。结果表明，过氧化物交联聚乙烯的力学性能有一定的提高，随着DCP含量的增加，交联PE的凝胶含量提高，而随着凝胶含量的提高，交联PE的拉伸强度提高，断裂伸长率下降；炭黑对材料有一定的补强作用，氧化锌的加入有助于交联反应和拉伸强度的提高。     

Nitrogen fertilizer use in rainfed agriculture

Agronomic efficiency (AE) is defined as the increase in economic yield of a crop per unit fertilizer applied. Components of AE are physiological efficiency and apparent recovery fraction. The latter can be further separated into uptake efficiency and availability index. Ways to increase the nitrogen fertilizer use efficiency in rainfed agriculture through fertilizer management are discussed.     

Bayesian bivariate generalized Lindley model for survival data with a cure fraction

The cure fraction models have been widely used to analyze survival data in which a proportion of the individuals is not susceptible to the event of interest. In this article, we introduce a bivariate model for survival data with a cure fraction based on the three-parameter generalized Lindley distribution. The joint distribution of the survival times is obtained by using copula functions. We consider three types of copula function models, the Farlie–Gumbel–Morgenstern (FGM), Clayton and Gumbel–Barnett copulas. The model is implemented under a Bayesian framework, where the parameter estimation is based on Markov Chain Monte Carlo (MCMC) techniques. To illustrate the utility of the model, we consider an application to a real data set related to an invasive cervical cancer study.     

Prediction of minimum fluidization velocity for vibrated fluidized bed

The prediction of minimum fluidization velocity for vibrated fluidized bed was performed. The Geldart group A and C particles were used as the fluidizing particles. The method based on Ergun equation was used to predict the minimum fluidization velocity. The calculated results were compared with the experimental data.The calculated results of minimum fluidization velocity are in good agreement with experimental data for Geldart group A particles. For group C particles, the difference between the calculated results and experimental data is large because of the formation of agglomerates. In this case, the determination of agglomerate diameter is considered to be necessary to predict the minimum fluidization velocity.     

大型下行式循环流化床反应器颗粒浓度分布研究

采用双光路光纤密度探头研究了内径418mm,高18米大型下行式循环流化床（其中下行床部分长度6．5m)反应器中的颗粒浓度分布，结果表明大直径下行床中颗粒浓度沿径向呈现中心均匀，近壁处存在高浓环形区的分布，这类似于小直径反应器中的结果，随着反应器直径的增加，颗粒浓度分布最大值的径向位置向边壁方向移动，即：当下行床放大时，中心颗粒浓度均匀分布区的面积占整个床层截面积的比例增大，在一种特殊设计的下行床边壁结构中测量了颗粒浓度沿径向的分布，实验结果说明边壁效应对下行床近壁区颗粒浓环的形成起到了重要作用，研究结果将有助于了解下行床反应的放大特性。