吐丝圈径对大规格高碳盘条组织性能的影响

计算与分析了斯太尔摩冷线上盘条的吐丝圈径、搭接密度及"佳灵"装置横向布风曲线之间的关系,研究了吐丝圈径的大小对大规格82B盘条组织和性能的影响,确定了大规格82B盘条最小吐丝圈径应为980mm.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

重介选煤厂自动化控制系统

介绍了重介选煤厂实现全自动控制的系统原理及所能实现的各项功能。     

固井声幅-变密度测井的影响因素分析

利用声幅－变密度测井进行固井质量的评价受到诸多因素的影响，各种影响因素对声幅－变密度测井资料的影响作用有较大的差异，根据大量测井资料分析和实验研究，对仪器偏心、测井时间，套管尺寸与重量，地层岩性，气侵、水泥环微间隔等因素的影响作用进行了较为深入的分析，为各种影响因素的识别与校正提出了相应的方法和依据。     

Modeling of Energy Density Distribution in Rock Mass on the Basis of Seismotectonic and Geodetic Data

Using the focal mechanisms of earthquakes taken place from 1950 to 1996, the type and direction of principal strains were established, which made it possible to determine the volume stress-strain state of the south-east flank of the Baikal rift zone on the basis of the inverse problem solution. The variations in the stress-strain fields and spatial distribution of the stored potential energy density were found by the displacements of the daylight surface points in Tunkinsk geodetic proving ground in 1975 - 1986.     

控制图在土坝粘土填筑干密度控制中的应用

应用统计控制图法，选用平均值——标准差、平均值——极差控制图法，控制24^#坝粘土填筑干密度值及施工偶然异常波动，早期提出警报，以保证土坝的施工质量。     

Preparation and properties of novel polyurethane insulating coatings based on glycerin‐terminated urethane prepolymers and blocked isocyanate

Novel polyurethane insulating coatings were prepared from the reaction of glycerin‐terminated polyurethane prepolymers (GPUPs) and a blocked isocyanate curing agent (BIC). The GPUPs were prepared from the reaction of one equivalent of polycaprolactone polyol (CAPA 210) with an excess amount of 4,4′‐methylene bis(phenyl isocyanate) (MDI) and subsequent reaction of the NCO‐terminated polyurethane with glycerin. The BIC was prepared from the reaction of trimethylol propane (TMP), toluene diisocyanate (TDI) and N‐methylaniline (NMA). The polyols and curing agent were characterized by conventional methods while the curing condition was optimized via gel content measurements. The curing kinetics of the polyurethane coating were investigated and the kinetic parameters derived. The crosslink densities of the samples were determined via the equilibrium swelling method, using the Flory–Rehner equation. The relationships between the crosslink density and the electrical, physical, mechanical and dynamic mechanical properties of the coatings were also studied. Copyright © 2005 Society of Chemical Industry     

Low density polyethylene and grafted lignin polyblends using epoxy‐functionalized compatibilizer: mechanical and thermal properties

Lignin was graft copolymerized with methyl methacrylate using manganic pyrophosphate as initiator. This modified lignin was then blended (up to 50 wt%) with low density polyethylene (LDPE) using a small quantity of poly[ethylene‐co‐(glycidyl methacrylate)] (PEGMA) compatibilizer. The mechanical properties of the blend were substantially improved by using modified lignin in contrast to untreated lignin. Differential scanning calorimetry studies showed loss of crystallinity of the LDPE phase owing to the interaction between the blend components. Thermogravimetric analysis showed higher thermal stability of modified lignin in the domain of blend processing. This suggested that there is scope for useful utilization of lignin, which could also lead to the development of eco‐friendly products. Copyright © 2005 Society of Chemical Industry     

Semiparametric Estimation in Time‐Series Regression with Long‐Range Dependence

Abstract. We consider semiparametric estimation in time‐series regression in the presence of long‐range dependence in both the errors and the stochastic regressors. A central limit theorem is established for a class of semiparametric frequency domain‐weighted least squares estimates, which includes both narrow‐band ordinary least squares and narrow‐band generalized least squares as special cases. The estimates are semiparametric in the sense that focus is on the neighbourhood of the origin, and only periodogram ordinates in a degenerating band around the origin are used. This setting differs from earlier studies on time‐series regression with long‐range dependence, where a fully parametric approach has been employed. The generalized least squares estimate is infeasible when the degree of long‐range dependence is unknown and must be estimated in an initial step. In that case, we show that a feasible estimate which has the same asymptotic properties as the infeasible estimate, exists. By Monte Carlo simulation, we evaluate the finite‐sample performance of the generalized least squares estimate and the feasible estimate.     

Finite‐Element Implementation of a Self‐consistent Texture Model with a Hardening Law Based on Dislocation Densities

A self‐consistent texture model is implemented in the finite‐element code ABAQUS/Explicit®. Hardening of the slip systems is described by evolution laws for dislocation densities, and the Bauschinger effect is included. With these ingredients the cold rolling of an IF‐steel is simulated and the evolution of texture and anisotropy is examined. The use of the dislocation based hardening law is found to have a significant effect on the evolution of the anisotropic yield surface, but only very little influence on the texture. Furthermore, the hardening model is used to investigate the evolution of dislocation densities in differently oriented grains during plane strain compression. It is found that the dislocation density varies greatly depending on orientation, an observation which can help to explain the orientation dependence of recrystallization.