激光结晶a-Si:H SOI离子注入和快速退火

本文对激光结晶a-Si∶H SOI结构砷注入和快速退火行为作了研究.a-Si∶H激光结晶有Lp-LCR,OD,FCR-2,FCR-1四个结晶区.用剖面电镜观察了结晶区的结构.扩展电阻测量表明Lp-LCR区中有两种扩散机制,即杂质在晶粒体内扩散和沿缺陷扩散.OD区中有三种扩散形式,除有上述两种以外,还有沿缺陷的扩散.首次比较了沿晶界和缺陷的扩散速度.     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

溅射靶材的应用及制备初探

随着电子及信息产业突飞猛进的发展，世界溅射靶材的需求越来越多，本文介绍了靶材的发展概况、分类和应用情况，以及靶材的特性要求．探讨Ni-Cr合金靶材的制备工艺，结果表明，产品能满足靶材特性要求。     

过共晶铝硅合金细化初晶硅的研究

研究了ZL8604过共晶铝硅合金初晶硅细化剂和加入方式与加入量以及影响细化效果的冶铸工艺因素,实验结果达到了技术指标要求。     

TiO_2压敏陶瓷晶粒半导化

本文主要研究 TiO_2陶瓷晶粒半导化的途径及晶粒电阻率的测试方法。实验结果表明,通过掺入Nb_2O_5施主杂质可以有效地降低晶粒电阻率,并使 TiO_2系陶瓷具有良好的压敏特性。     

SOLUBILISATION OF NITROGENOUS CONSTITUENTS OF BREWERS' SPENT GRAIN

The extraction of nitrogenous material from Brewers' spent grain (BSG) by solvents (water, sodium chloride solution, aqueous alcohol, acidic and alkaline solutions) commonly used to extract cereal proteins, resulted in the relatively low (0·2 to 8·5%) recovery of the total nitrogen. The recovery of nitrogenous material by the use of aqueous alkaline solutions was increased from 3–4% to 41% when the BSG was subjected to cellulase incubation prior to extraction. Approximately 75% of the nitrogen was solubilized with trifluoracetic acid. Detergent solutions (acid, neutral) solubilized more than 80% of the total nitrogen of the BSG. The low solubility of the nitrogenous constituents by conventional protein solvents could be the result of association between cellulosic material and protein.     

ECAP细化晶粒法的仿真与分析

ECAP(Equal Channel Angular Extrusion)方法，是实现材料纯剪切变形的有效方法。本文采用有限元（FEA）分析软件ANSYS对Al的挤压过程进行仿真与分析。分析结果表明：外切角Φ、圆角半径、试样与凹模之间的摩擦系数、凹模本身的特性（如弹性模量、泊松比等）等等，对材料的变形量都有不同程度的影响。     

Ti/Al Interaction and Austenite Grain Control in Crankshaft Manufacturing with 38MnSiVS5 Steel

38MnSiVS5 steel is similar to 38MnVS6 steel (EN), the difference being the addition of a small Ti content. Typical Ti and Al contents in the chemical composition of 38MnSiVS5 steel are Ti=0.020 and Al=0.035 mass%. Both elements combine easily with nitrogen, especially Ti, and it has been observed that relatively high Al levels are harmful for austenite grain size control at reheating temperatures. In this work 38MnSiVS5 steel is used to manufacture a large number of castings, varying only the Ti and Al contents and obtaining ingots with a different Ti/Al ratio in each case. The results show that abnormal growth of the austenitic grain occurs irrespective of the Ti and Al contents, due fundamentally to the partial dissolution and coarsening of TiN precipitates. However, the steels with high Al contents present worse behaviour due to the formation of a second type of precipitates, namely AIN, which quickly dissolve between 1000 and 1100°C, causing a drastic decline in local pinning forces that gives rise to more pronounced abnormal growth of the affected grains.     

CONSTITUTE AND PROPERTY OFα-Ti AFTER HYDRIDING TREATMENT

研究了氢化处理对退火α-Ti 板材的组织、结构及性能的影响。α-Ti 在室温出现两种结构的氢化物:有序的fctγ相(TiH)和fccδ相(TiH_2)。分析了用X 射线衍射只查觉到δ相的原因。氢化物的数量及形态影响除氢后基体的晶粒组织。控制氢含量可以改善拉伸性能及疲劳性能。