模拟焊后热处理对锅炉用钢板SA-299力学性能的影响

对新日铁供货的SA-299钢板取样进行了供货状态及610～650℃/8h炉冷的模拟焊后热处理,以进行力学性能对比试验。试验结果表明,经过630℃/8h炉冷的模拟焊后热处理后σs降低25～40MPa、σb降低55～65MPa,但力学性能符合ASMESA-299标准和采购规程C1F19-98的要求。     

Question hard, answer simply: A comment on Storms et al. (2003).

It seems clear that, for whatever reasons, the dementia of the Alzheimer type patient group (as well as other patient groups) exhibits behavior that is different from the normal control group. G. Storms, T. Dirikx, J. Saerens, S. Verstraeten, and P. P. De Deyn (2003) rightfully argue that the observed behavior (similarity judgments) does not tell us the source (cause) of the differences between the 2 groups. Rather, the focus of the study should be placed more on finding the ways the 2 groups are different. They also point out various methodological problems in some of the previous attempts to characterize the nature of the differences. Further methodological issues in G. Storms et al.'s study are examined. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Prediction of the energy dissipation rate in ductile crack propagation

In this paper, energy dissipation rate D vs. Δa curves in ductile fracture are predicted using a ‘conversion’ between loads, load‐point displacements and crack lengths predicted by NLEFM and those found in real ELPL propagation. The NLEFM/ELPL link was recently discovered for the DCB testpiece, and we believe it applies to other cracked geometries. The predictions for D agree with experimental results. The model permits a crack tip toughness R(Δa) which rises from J_c and saturates out when (if) steady state propagation is reached after a transient stage in which all tunnelling, crack tip necking and shear lip formation is established. J_R is always greater than the crack tip R(Δa) and continues to rise even after R(Δa) levels off. The analysis is capable of predicting the usual D vs. Δa curves in the literature which have high initial values and fall monotonically to a plateau at large Δa. It also predicts that D curves for CCT testpieces should be higher than those for SENB/CT, as found in practice. The possibility that D curves at some intermediate Δa may dip to a minimum below the levelled‐off value at large Δa is predicted and confirmed by experiment. Recently reported D curves that have smaller initial D than the D‐values after extensive propagation can also be predicted. The testpiece geometry and crack tip R(Δa) conditions required to produce these different‐shaped D vs. Δa curves are established and confirmed by comparison with experiment. The energy dissipation rate D vs. Δa is not a transferable property as it depends on geometry. The material characteristic R(Δa) may be the ‘transferable property’ for scaling problems in ELPL fracture. How it can be deduced from D vs. Δa curves (and by implication, J_R vs. Δa curves) is established.     

Shallow Turbulent Flows by Video Imaging Method

Shallow turbulent flows were produced in a tank of small thickness to study the friction effects on large-scale turbulent motion of small depth. The tank was constructed of two parallel walls. The space between the parallel walls (4.4, 1.57, and 0.59 cm) was small compared with the height (107 cm) and the width (212 cm) of the tank, and was varied during the experiments for different friction effects. Turbulent flows were produced by the injection of water in the form of starting jets into the tank filled with water. The large-scale turbulent flow in the small space between the walls of the tank is confined to essentially two-dimensional motion, and the motion is retarded by the force of friction. Dye was injected with the source fluid as the tracer for the highly unsteady and quasitwo-dimensional turbulent motion. From the initiation of the turbulent motion at the source to the final interaction of the jets with the tank bottom, the entire sequence of events was recorded by a pair of video cameras. The depth-averaged concentration of the dye was analyzed using the recorded video images.     

一种嵌入式TCP／IP的实现

针对许多小型嵌入式系统要求结构紧凑、开销小的TCP／IP协议栈的需求，提出一种可移植的非路由器TCP／IP原型的实现。该TCP／IP原型基于某种小型嵌入式系统，依据RFC1122兼容性规定，提供IP、ARP、TCP、UDP服务和Berkeley Socket编程接口。该实现代码短小，开销低，性能能够满足多数应用需求，具有较强的可移植性。     

水工隧洞内消能工的研究及应用进展

对于高水头、大流量的水电工程,以往的消能工具有一定的局限性,研究表明,把大面积遭受高速水流作用改为局部承受的消能方式,是高坝泄洪消能的一条有效途径。内消能工主要有孔板(洞塞)式消能工、旋流式消能工、消力井等3种形式。实践表明,内消能工对改善大坝下游水流流态,保护下游环境,保障下游边坡稳定等有积极作用,综合考虑,旋流式消能工具有较大优越性。对水工隧洞内部消能技术尚需开展进一步的研究与实践。     

能量分析法在空气源热泵除霜中的应用

针对空气源热泵冷热水机组冬季制热运行时换热器结霜与除霜的问题，提出了一种能量分析法。从能量转换和能量传递的角度出发，分析一种常见的除霜方法——逆循环除霜。通过对除霜过程的讨论，找出了相应的减少除霜损失的方法。     

POWER OPTIMIZATION OF FINITE STATE MACHINE BASED ON GENETIC ALGORITHM

Using state assignment to minimize power dissipation and area for finite state machines is computationally hard.Most of published results show that the reduction of switching activity often trades with area penalty.In this paper,a new approach is proposed.Experimental results show a significant reduction of switching activity without area penalty compared with previous publications.     

宽流道板式换热器在氧化铝生产种子分解过程中的应用

介绍了宽流道板式换热器的结构、特点及在氧化铝生产种子分解过程中的应用。     

浅析分户供热的计量

本文介绍了国外在供热分户计量方面的测定原理、手段和设备,费用分配原则,仪表与系统的配合和安装方式,并就其与国内系统的配合提出了建议。