利用热管纺丝技术一步法生产FCY

利用平板型热管纺丝装置对普通高速纺丝机进行技术改造，并一步法生产出充分结晶的ＰＥＴ纤维（ＦＣＹ）。该纤维可直接用于织造，调节热管温度、热管安装位置可获得满足后道工序不同需要的ＦＣＹ。     

High-Pressure (up to 140 MPa) Dynamic Viscosity of the Methane and Toluene System: Measurements and Comparative Study of Some Representative Models

The dynamic viscosity of toluene and methane mixtures containing 25.03, 37.19, 49.95, 64.11, and 95.00 mol% methane has been measured using a falling-body viscometer. The measurements (280 data points) have been performed in the temperature range 293.15 to 373.15 K and at pressures up to 140 MPa. The data have been discussed in the framework of recent representative models (hard-sphere scheme, friction theory, and free-volume model) as well as with simple mixing laws and empirical models (particularly the LBC model and the self-referencing model) used in the literature. This comparative study shows that the average absolute deviation of the models is between 4.9 and 26.8%, and the maximum deviation is between 11.6 and 49.5%.     

一个高电阻值测量电路

介绍一种新的高阻测试方法，可满足对高达１×１０＾１６Ω的测试要求。测试结果显示，对于１×１０＾１３Ω重复误差优于±２％。高阻测试电路通过接口与６８０９微机配套使用，操作简便，读数直观，便于长时间重复测量。     

Solid-liquid phase equilibria of benzene + 2-methyl-2-propanol system under high pressures

Solid-liquid phase equilibria of the benzene + 2-methyl-2-propanol system have been investigated at temperatures from 278 to 323 K and pressures up to 300 MPa using a high-pressure optical vessel. The uncertainties of the measurements of temperature, pressure and composition are within ±0.1 K, ±0.5 MPa, and ±0.001 mole fraction, respectively. The freezing pressure at a constant composition increases monotonously with pressure. The eutectic point shifts to a higher temperature and benzene-rich composition with increasing pressure. In order to describe the pressure-temperature-composition relation of high-pressure solid-liquid phase equilibria, a new simple equation has been proposed as follows:

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

反相高效液相色谱法测定meso-四苯基卟啉钴的纯度

采用反相高效液相色谱法测定合成meso-四苯基卟啉钴的纯度;以甲醇乙腈二氯甲烷(体积比为55∶35∶10)为流动相,ShimpackCLCODS柱(150mm×6.0mmi.d,5μm)为分离柱,流速为1.5mL/min,检测波长420nm;meso四苯基卟啉钴的测定在1.0～10μg/mL时线性关系良好(相关系数r=0.9993),加标回收率为97.03%～101.42%,重复进样的相对标准偏差RSD为0.64%～2.92%(n=5)。方法的准确度高,精密度好,实际应用效果好。