常规两段浸出法提高锌焙烧矿中铜回收率的研究

分析了不同湿法炼锌工艺锌焙烧矿中回收铜的工艺,发现各工艺都存在不同的工艺缺点。借鉴国内锌冶炼企业开展的常规两段浸出法提高铜回收率的生产经验,进行了锌焙烧矿中铜、铁、硅的浸出机理研究,并且根据该机理提出了常规两段浸出法的改进工艺流程,按照该工艺流程开展了试验研究,将铜的回收率提高到了76.41%。     

The laws of silicon ingot formation by combustion reaction

The formation of a phase pure silicon ingot from SiO₂+Al+KClO₃ and Na₂SiO₃+Al+KClO₃ systems was investigated thermodynamically and experimentally under combustion mode, known also as self-propagating high-temperature synthesis (SHS). The regularities of combustion and phase formation versus KClO₃ concentration by a thermocouple technique were obtained. The morphology, chemical and phase composition of the silicon ingot were analyzed by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and ICP-analysis. The method reported here proved effective in producing silicon ingots with a purity of 98%.     

Formation of a chromium-carbide conversion coating on silicon carbide

The formation of a chromium-carbide conversion coating on SiC was achieved using the pack-cementation technique. The conversion coating is intended to improve the corrosion resistance of SiC and its derivatives, such as SiC-base continuous fibers and composites, by forming a protective Cr₂O₃ scale upon exposure to high-temperature corrosive environments. Different pack chemistry and processing parameters were evaluated in the laboratory. Results indicated that the coating morphologies and compositions achieved were significantly affected by variation of these processing factors. In this paper, the conversion coating obtained from one of the systems investigated is reported. The coating consists of a multilayered structure with each of the sublayers containing a high-Cr concentration. In addition, the coating surface is relatively dense and pore free compared to the underlying SiC substrate material. A dense and pore-free morphology is highly desirable for coating applications, especially on porous substrates. The multilayered coating structure consists of the following sublayers: Cr₂₃C₆/Cr₇C₃/Cr₇C₃+Cr₃Si/Cr₅Si₃C_x/SiC substrate.     

高炉铁水含硅量的混沌局部线性预测

对莱钢1号高炉(750 m3)、临钢6号高炉(380 m3)铁水含硅量([Si])进行了混沌局部线性预测.结果表明,两 座高炉[Si]的一步预测的命中率在[Si]±0.1％的范围内均达到80.0％以上,对莱钢1号高炉(b)类样本甚至达89.1％,且预 测精度在10-2数量级,对实际生产具有很好的指导作用.     

Effect of oxygen precipitates in solar grade silicon on minority carrier lifetime and efficiency of solar cells

The effect of oxygen precipitates on minority carrier lifetime and performance of solar cell was studied by means of Fourier Transform Infrared Spectroscopy (FTIR), quasi-steady state photoconductance (QSSPCD), optical microscope, spectrumresponse and solar cell efficiency test. The minority carrier lifetime and performance of solar cell reduced depend on oxygen precipitates. A few of oxygen precipitates have formed after single-step annealing; and they do not impact the efficiency dramatically. Pre-annealing at 650 ℃ for 4 h enhances the oxygen precipitation when it is subjected to middle temperature annealing. The solar cells performance decayed sharply. Especially annealing at 950 ℃ for 3 h, the V os and I sc of cells decrease 12% and 25% respectively. Few oxygen precipitates have formed in silicon after high temperature annealing at about 1050 ℃ whether pre-annealing is used or not, and the performance of cells is notbe affected.     

硅对定向凝固Ni3Al基合金IC6A微观组织和性能的影响

利用扫描电镜(SEM)、透射电镜(TEM)、电子探针(EPMA)、能谱(EDS)和X射线衍射(XRD)技术研究了硅对定向凝固Ni3Al基合金IC6A微观组织的影响。结果表明在IC6A合金中添加0．10％～0．20％Si(质量分数,下同)会使合金的枝晶间区析出块状的Mo1.24Ni0.76相和Mo6(Ni0.75Si0.25)7相,当硅的添加量达到0．30％时,合金的枝晶间区除了析出这两种相外,还有针状的δ-NiMo相析出。这相的析出不利于合金的高温持久性能,它们的硬度较大,只能通过孪晶的方式变形。硅有利于提高IC6A合金的高温抗氧化性能,而对合金的抗腐蚀性能和瞬时拉伸性能无明显影响。     

AI-Li/SiCp composites and Ti-AI alloy powders and coatings prepared by a plasma spray atomization (PSA) technique

There has been increasing use of Al-Li alloys in the aerospace industry, due mainly to the low density and high elastic modulus of this material. However, the problem of low ductility and fracture toughness of this material has limited its present application to only weight- and stiffness-critical components. Development of Al-Li/ceramic composites is currently being investigated to enhance the service capabilities of this material. The Ti-Al alloy is also of interest to aerospace-type applications, engine components in particular, due to its attractive high-temperature properties. Preparation of fine powders by plasma melting of composite feedstock and coatings formed by plasma spraying was carried out to examine the effect of spray parameters on the microstructure and properties of these materials. Characterization of the powders and coatings was performed using the scanning electron microscope and image analyzer. Examination of the plasma-sprayed powders and coatings has shown that in the Al-Li/SiC composite there is melting of both materials to form a single composite particle. The SiC reinforcement was in the submicron range and contributed to additional strengthening of the composite body, which was formed by a cold isostatic press and consolidated by hot extrusion or hot forging processes. The plasma-sprayed Ti-Al powder showed four categories of microstructures: featureless, dendritic, cellular, and martensite-like.     

硅黄铜铸件的渗漏缺陷分析

为了满足耐海水腐蚀、高导热率和承压能力要求,冷却器盖均采用硅黄铜制造。某厂在冷却器盖的生产过程中,铸件废品率高达60%,主要问题是铸件在水压测试中出现渗漏。分析了冷却器盖铸件的渗漏缺陷。结果表明:硅的加入量和浇注温度偏高,硅熔化不完全是导致此类铸件产生渗漏的主要原因。针对性地采取措施后,冷却器盖铸件的成品率大幅提高,达到了90%以上。     

碳化硅晶须双重加热合成的研究

双重加热法是低成本、大批量合成碳化硅晶须的新技术，合成温度低、合成时间短、生成率高。对以炭黑和二氧化硅微粉为原料、用双重加热法合成碳化硅晶须的工艺过程进行了研究。观察了不同合成时间、合成温度和催化剂条件下的碳化硅晶须，揭示出不同工艺参数对合成的碳化硅晶须的产出率，微观形貌、直径和长度范围的影响。结果表明，催化剂的使用可以加快反应速度，提高碳化硅晶须的生成率，合成过程为VLS。实验中初步得到的最佳经济工艺参数为：Fe2O3的用量为2％，合成时间为1．5h，合成温度为1250℃。此时的该工艺条件下碳化硅晶须的生成率可达80％，晶须平均直径为0．6μm，平均长度为30μm。     

晶闸管弧焊整流器的全集成化控制

在保留双反星形可控整流主电路优点的同时，根据手工焊和氩弧焊的工艺特点，对控制电路作了全集成化设计。介绍了稳弧电路、同步移相电路、触发电路及外特性控制电路的设计特点，对各单元电路进行了具体的分析。