The Minimum PAPR Code for OFDM Systems

In this letter, a block code that minimizes the peak‐to‐average power ratio (PAPR) of orthogonal frequency division multiplexing (OFDM) signals is proposed. It is shown that peak envelope power is invariant to cyclic shift and codeword inversion. The systematic encoding rule for the proposed code is composed of searching for a seed codeword, shifting the register elements, and determining codeword inversion. This eliminates the look‐up table for one‐to‐one correspondence between the source and the coded data. Computer simulation confirms that OFDM systems with the proposed code always have the minimum PAPR.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Optimal and self‐tuning fusion Kalman filters for discrete‐time stochastic singular systems

Based on the optimal fusion estimation algorithm weighted by scalars in the linear minimum variance sense, a distributed optimal fusion Kalman filter weighted by scalars is presented for discrete‐time stochastic singular systems with multiple sensors and correlated noises. A cross‐covariance matrix of filtering errors between any two sensors is derived. When the noise statistical information is unknown, a distributed identification approach is presented based on correlation functions and the weighted average method. Further, a distributed self‐tuning fusion filter is given, which includes two stage fusions where the first‐stage fusion is used to identify the noise covariance and the second‐stage fusion is used to obtain the fusion state filter. A simulation verifies the effectiveness of the proposed algorithm. Copyright © 2008 John Wiley & Sons, Ltd.     

Impact of the addition of an enzyme pool on an activated sludge system treating dairy wastewater under fat shock loads

BACKGROUND: The application of lipase‐rich enzyme pools (such as the crude solid enzymatic preparation (SEP) obtained from Penicillium restrictum solid‐state fermentation of agro‐industrial wastes) to activated sludge systems may be an effective strategy for preventing various operational problems. The continuous addition of SEP to the treatment system can become cost‐prohibitive when in situ production and/or storage are factored in. The application of SEP to high‐fat wastewater treatment would only be justified as an emergency measure, such as a sudden increase in the fat content of the bioreactor influent. Therefore, the primary objective of this work was to investigate the efficiency of a crude SEP during fat shock loads, simulated through the periodic addition of dairy industry waste containing high fat concentrations to the feed stock of an activated sludge system, operated in continuous mode. RESULTS: The test bioreactor exhibited a higher average chemical oxygen demand (COD) removal efficiency than the control bioreactor (83% for control and 90% for test) and the fat accumulation in the biological flocs of the test bioreactor was 3.2 times lower than that in the control bioreactor. Turbidity was also lower in the effluent of the test bioreactor (123 and 66 FTU in control and test, respectively) and it had a shorter recovery time between shock loads, especially when the interval between loads was shorter than one month (biweekly and weekly shock loads). CONCLUSION: The addition of SEP during fat overloads in the reactor feed maintained efficient COD removal in the test bioreactor for 270 days without any operational problems. Copyright © 2008 Society of Chemical Industry     

Sensitometric characteristics of an all‐solid‐state photoelectrochromic pixel for an electrochromic light‐addressable display

Abstract— An all solid‐state photoelectrochromic element (PECE) was developed on the basis of electrochromic layers of WO₃ and polyaniline with a layer of polymer electrolyte placed on a base of polyamidosulfoacid, in which a thin‐film CdS_xSe_1?x photoresistor was used as an electronic key. The dependence of the sensitometric characteristics of the PECE on the applied voltage was studied.     

Heat resistance of Escherichia coli O157:H7 in cook‐in‐bag ground beef as affected by pH and acidulant†

Summary The heat resistance of a four‐strain mixture of Escherichia coli O157:H7 was tested. The temperature range was 55–62.5 °C and the substrate was beef at pH 4.5 or 5.5, adjusted with either acetic or lactic acid. Inoculated meat, packaged in bags, was completely immersed in a circulating water bath and cooked to an internal temperature of 55, 58, 60, or 62.5 °C in 1 h, and then held for pre‐determined lengths of time. The surviving cell population was enumerated by spiral plating meat samples on tryptic soy agar overlaid with Sorbitol MacConkey agar. Regardless of the acidulant used to modify the pH, the D ‐values at all temperatures were significantly lower (P < 0.05) in ground beef at pH 4.5 as compared with the beef at pH 5.5. At the same pH levels, acetic acid rendered E. coli O157:H7 more sensitive to the lethal effect of heat. The analysis of covariance showed evidence of a significant acidulant and pH interaction on the slopes of the survivor curves at 55 °C. Based on the thermal‐death–time values, contaminated ground beef (pH 5.5/lactic acid) should be heated to an internal temperature of 55 °C for at least 116.3 min and beef (pH 4.5/acetic acid) for 64.8 min to achieve a 4‐log reduction of the pathogen. The heating time at 62.5 °C, to achieve the same level of reduction, was 4.4 and 2.6 min, respectively. Thermal‐death–time values from this study will assist the retail food processors in designing acceptance limits on critical control points that ensure safety of beef originally contaminated with E. coli O157:H7.     

Use of recycled copper slag for blended cements

Copper slag is a by‐product generated during smelting to extract copper metal from the ore. The copper slag obtained may exhibit pozzolanic activity and may therefore be used in the manufacture of addition‐containing cements. In this paper the effect of the incorporation of the copper slag in cement is measured. Blends of copper slag with Portland cement generally possess properties equivalent to Portland cement containing fly ash, but very different to the silica fume incorporation. Copper slag and fly ash reduce the heat of hydration more effectively than silica fume in mortars. The replacement of 30% cement by copper slag reduces the flexural and compressive strength in a similar way to fly ash; however, after 28 days, the reduction is less than the percentage of substitution. Hydrated calcium aluminate phases were analysed using scanning electron microscopy (SEM) and X‐ray diffraction (XRD) techniques. The pozzolanic activity of copper slag is similar to that of fly ash and higher than silica fume. In the presence of low water/cement ratios, certain pozzolanic materials produce a very compact cement paste that limits the space available for hydration products, a determining factor in the formation of hydrated calcium aluminates. SEM was found to be a useful analytical technique when aluminates are formed and can be clearly detected by XRD. Copyright © 2008 Society of Chemical Industry     

Biotransformation of three aromadendrane‐type sesquiterpenoids by Aspergillus wentii

BACKGROUND: The biotransformation of sesquiterpenoids, which are a large class of naturally occurring compounds, using microorganisms as a biocatalyst to produce useful novel organic compounds was investigated. The biotransformation of sesquiterpenoids, (+)‐aromadendrene ( 1 ), (−)‐alloaromadendrene ( 2 ) and (+)‐ledene ( 3 ) has been investigated using Aspergillus wentii as a biocatalyst. Results: Compound 1 was converted to (−)‐(10S,11S)‐10,13,14‐trihydroxyaromadendrane ( 4 ). Compound 2 was converted to (+)‐(1S,11S)‐1,13‐dihydroxyaromadendrene ( 5 ) and (−)‐5,11‐epoxycadin‐1(10)‐en‐14‐ol ( 6 ). Compound 3 was converted to compound 6 , (+)‐(10R,11S)‐10,13‐dihydroxyaromadendr‐1‐ene ( 7 ) and (+)‐(10S,11S)‐10,13‐dihydroxyaromadendr‐1‐ene ( 8 ). The structure of the metabolic products has been elucidated on the basis of their spectral data. CONCLUSION: Compound 1 gave only one product that was hydroxylated at C‐10, C‐13 and C‐14. By contrast, compounds 2 and 3 gave a number of products, one of which was common. The differences in oxidation of 1–3 are due to the configuration of the C‐1 position. Compounds 4–8 were new compounds. Copyright © 2008 Society of Chemical Industry     

Note on ‘Construction of Double Sampling s‐Control Charts for Agile Manufacturing’

He and Grigoryan (Quality and Reliability Engineering International 2002; 18 :343–355) formulated the design of a double‐sampling (DS) s control chart as an optimization problem and solved it with a genetic algorithm. They concluded that the DS s control charts can be a more economically preferable alternative in detecting small shifts than traditional s control charts. We explain that, since they only considered the average sample size when the process is in control, their conclusion is questionable. Copyright © 2006 John Wiley & Sons, Ltd.