Influence of Ti Powder Characteristics on Combustion Synthesis of Porous NiTi Alloy

Porous NiTi shape memory alloy (SMA) is a novel biomedical material used for human hard tissue implant .The influence of elemental titanium powder characteristics such as powder morphology, particle size and specific surface area( SSA) on the minimal ignition temperature ,combustion temperature and final product of porous Ni-Ti SMA fabricated by combustion synthesis method was investigated in this paper by scanning electron microscopy (SEM) and laser diffraction.The preliminary data indicated that the titanium powder characteristics had a strong effect on combustion synthesis of porous NiTi SMA.     

Thermal Expansion Behavior of La1—xSrxMn1—yCoyO3—δ Perovskites

The thermal expansion behavior of La1-xSrxMn1-yCoyO3-δ (x=0.2-0.4, y=0.1-0.3) perovskites in air has been investigated. The average linear thermal expansion coefficients increased with increasing Sr content up to 40 mole fraction or Co content up to 30 mole fraction. The expansion is generally attributed to an increase in the average cation radius as some of the cations in the perovskite are reduced in valence when oxygen ions are removed from the structure.     

信号时域积分性质的一个推广应用

对信号进行运算（卷积运算，傅氏变换，拉纸变换）时，应用时域积分性质，得出由函数导数的运算式求取原函数的相应运算结果的一般性计算公式，使时域积分性质的应用得到推广。     

刚性棒状全芳香液晶聚酯的合成及性质的研究

以溴和苯基取代的对苯二甲酰氯及2，2′-二甲基联苯-4，4′-二甲酰氯作为单体，分别与甲基、叔丁基、苯基取代的对苯二酚经熔融缩聚反应，合成一类具有刚性棒状结构的全芳香液晶聚酯。聚酯的热性质以TGA、DSC，热台偏光显微镜研究。所有的聚酯均为热致性液晶，它们具有相对较低的转变温度，在普通的有机溶剂中具有较好的溶解性质。     

HTR-10燃料元件装卸系统冷态调试

10MW高温气冷实验堆（HTR－10）是一座球床堆，由燃料元件装卸系统实现燃料元件的装卸和循环，且不需要停堆，为保证HTR－10的正常运行，燃料元件装卸系统必须安全，可靠，为此，必须对燃料元件装卸系统进行周密，细致的调试试验和验证，本文介绍了燃料元件装卸系统冷调试的主要调试项目，调试方法和调试结果。     

降低氧化铝生产中熟料折合比的探讨

在氧化铝生产过程中，熟料折合比是烧结法一项重要的综合性指标，本文通过对熟料折合比的定义、计算公式的剖析，分析了生产过程中影响熟料折合比的主要因素，对有效降低熟料折合比的措施进行了探讨。     

线缆护套材料在我国西部环境中的试验研究

本文通过对线缆外护套材料在我国西部地区严酷环境试验站中土壤和大气1～5年的试验结果分析，总结了塑料护套材料的耐蚀性能。为线缆护套的防护设计、合理选材及制定标准提供科学依据。     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

Effect of C/Ti ratio on the laser ignited self-propagating high-temperature synthesis reaction of Al-Ti-C system for fabricating TiC/Al composites

TiC/Al composite was successfully synthesized utilizing laser ignited self-propagating high-temperature synthesis (SHS) of Al-C-Ti system with the different C/Ti molar ratio. When the molar ratio of C to Ti is below 1:1 in the starting materials, in addition to fine TiC particulates, a large amount of Al₃Ti phase was found in the composites; however, when the molar ratio of C to Ti is 1:1 in the starting materials, the Al₃Ti phase was almost completely eliminated and the distribution of TiC particulates generally appeared to be more homogeneous throughout the products synthesized.