低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓联接失效分析与改进

分析了CFH-Ⅱ型翻车机传动齿轮轴承座的座脚螺栓组联接失效(松动)的原因，得出控制和保证合适的螺栓组联接预紧力是防止螺栓联接失效(松动)的关键；依据现场条件，对座脚螺栓进行了设计改进；提出了一种适合现场使用的螺栓预热伸长的装配方法，经实践验证此法是简单可靠的装配方法。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。     

T8钢－聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性、磨料磨损特性及对土壤的减粘降阻性能与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％～２２．２７％     

Improving Wear Resistance of the Ni-base Thermal Spray-Welding Coating Using Rare Earths

ＩｍｐｒｏｖｉｎｇＷｅａｒＲｅｓｉｓｔａｎｃｅｏｆｔｈｅＮｉｂａｓｅＴｈｅｒｍａｌＳｐｒａｙＷｅｌｄｉｎｇＣｏａｔｉｎｇＵｓｉｎｇＲａｒｅＥａｒｔｈｓＺｈａｉＧｕａｎｇｊｉｅ（翟光杰）（ＩｎｓｔｉｔｕｔｅｏｆＰｈｙｓｉｃｓ，ＡｃａｄｅｍｉｃａＳｉ...     

通用绘图软件NuSlides中的面向对象的用户界面设计

本文描述在Ｕｎｉｘ环境下开发的通用绘图软件ＮｕＳｌｉｄｅ中的图形用户界面的设计思想和实际方法。其特点是基子面向对象的技术，提供多窗口、菜单驱动、选择面板、键盘输入等多种才法。该图形用户界面具有灵活性、可扩充性和易使用性。     

Intracellular localization of the antitumour drug adriamycin in living cultured cells: A confocal microscopy study

The intracellular distribution of the anthracyclinic antibiotic adriamycin in living cultured cells has been investigated by confocal microscopy. In human melanoma cells (M14), adriamycin was localized inside the nuclei. When adriamycin-treated M14 cells were allowed to recover in drug-free medium, a complete efflux of the drug from the nucleus was revealed. In recovered cells, a weakly fluorescent signal was observed in the perinuclear region. When M14 cells were recovered in a medium containing colcemid, a microtubule depolymerizing agent, the drug transport from the nucleus to the cell periphery appeared to be inhibited, suggesting that the microtubule network is strongly involved in drug transport mechanisms. In multidrug-resistant (MDR) cells the intracellular location of adriamycin was shown to be noticeably different from that of the parental wild-type cells. In particular, in resistant human breast carcinoma cells (MCF-7), adriamycin appeared to be exclusively located within the cytoplasm whereas the nuclei were shown to be completely negative. When adriamycin treatment was performed in association with MDR revertants, such as Lonidamine (inhibitor of the energy metabolism) or verapamil (inhibitor of the P-glycoprotein efflux pump), a marked enhancement of the cytoplasmic signal was observed in resistant cells. Under these conditions, adriamycin appeared concentrated in the perinuclear region, but the nuclei were still negative. Confocal microscopy proved to be a very useful method for the study of the intracellular transport of fluorescent substances, such as anthracyclinic antibiotics, and for the investigation of the multidrug resistance phenomenon in tumour cells.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Energy use in controlled temperature marine aquaculture

Temperature control offers benefits in land‐based marine aquaculture: stock growth rates may be enhanced by heating in winter; mortality rates in summer may be reduced by cooling. However, if the plant is not well designed, temperature control may create very large energy demands. This paper describes the application of temperature control in abalone aquaculture in New Zealand, with a focus on energy considerations in plant design. An abalone farm using a semi‐closed water conditioning system is used as a case study for which an energy model, based on a heat pump system, is developed. The model is used to determine the impact of plant design and tank conditions on the economics of the operation. Copyright © 2002 John Wiley & Sons, Ltd.     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。