SiGe: An attractive material for post-CMOS processing of MEMS

This work gives an overview of the different developments for silicon germanium (Si_1−xGe_x) from a MEMS post-processing perspective. First, the maximum processing temperature that does not introduce any damage or degradation into the standard characteristics of the CMOS driving electronics is specified. Then, the optimal type of silicon and germanium gas sources and deposition technique that results in an economical process are identified. Next, the selection criteria for a low thermal budget doping method and doping species are discussed. Finally, the advantage and disadvantage for the different approaches implemented for enhancing the physical properties of poly Si_1−xGe_x at a CMOS backend compatible temperature are highlighted. It is shown that the optimal method depends on the application requirements and the CMOS technology used for realizing the driving electronics.     

Preadhesion Laser Treatment of Aluminum Surfaces

An excimer laser may be used for preadhesion treatment of aluminum alloys. This method presents an alternative to the use of ecologically unfriendly chemicals involved in conventional anodizing pretreatments.

Experimental results indicate that preadhesion laser surface treatment significantly improved the shear strength of modified-epoxy bonded aluminum specimens compared with untreated and anodized substrates. The best results were obtained with laser energy of about 0.2 J/Pulse/cm² where single lap shear strength was improved by 600-700% compared with that of untreated Al alloy, and by 40% compared with chromic acid anodizing pretreatment.

The mode of failure changed from adhesive to cohesive as the number of laser pulses increased during treatment. The latter phenomenon has been correlated with morphology changes as revealed by electron microscopy, and chemical modification as indicated by Auger and infrared spectroscopy.

It can be concluded that the excimer laser has potential as a precise, clean and simple preadhesion treatment of Al alloys.     

浅谈玻璃钢的加工

本文在实际研究和应用的基础上，对玻璃钢的传统加工方法和特种加工方法，如激光切割、纯水射流切割和磨料水射流切割作了简要论述。     

对策论在雷达阵地综合防护效能分析中的应用

针对雷达阵地的防护特点,运用对策论的基本原理探索雷达阵地综合防护效能分析问题.构建了雷达阵地综合防护效能分析指标体系,结合对策论建立了评估模型,并用实例检验该方法具有较好的应用价值.     

Monitoring slope deformation using a 3-D laser image scanning system:a case study

An ILRIS-36D 3-D laser image scanning system was used to monitor the Anjialing strip mine slope on Pingshuo in Shanxi province.The basic working principles,performance indexes,features and data collection and processing methods are illustrated.The point cloud results are analyzed in detail.The rescale range analysis method was used to analyze the deformation characteristics of the slope.The results show that the trend of slope displacement is stable and that the degree of landslide danger is low.This work indicates that 3-D laser image scanning can supply multi-parameter,high precision real time data over long distances.These data can be used to study the distortion of the slope quickly and accurately.     

树脂增强选择性激光烧结多孔金属件的研究

针对选择性激光烧结(SLS)间接方法成型的金属零件形坯,经脱脂和高温烧结后形成的零件存在大量孔隙和空洞,其致密度和强度都较低,不能满足实际应用要求的问题,采用改性耐高温环氧树脂浸渗零件烧结坯的方法,使多孔金属件致密化,并粘结内部金属网架,提高零件的机械性能.对浸渗烧结坯的拉伸强度的测试和扫描电镜(SEM)以及热失重(TGA)的分析结果表明,浸渗树脂后的烧结坯拉伸强度提高了约4倍;改性环氧树脂和金属网架粘结在一起,形成一个密实的网络结构,致密度大幅提高;零件可在200℃的温度下使用.该方法可以制造注塑模具和功能零件.     

TH-PPM UWB通信系统多址性能研究

介绍了TH-PPM UWB信号,在AWGN信道和多用户干扰条件下对系统的性能进行了分析,包括误码率分析和系统所能接入的最大用户数,对其误码率进行了仿真.结果表明,随着接入用户数目的增加,系统误码率也增加,而增大重复码长度和脉冲重复时间则可降低系统误码率,但增加脉冲重复时间会降低信息传输速率.     

Investigation of Flow Patterns in Continuous‐flow Stirred Vessels by Laser Doppler Velocimetry

The flow structure of a continuous‐flow reactor stirred by a Rushton turbine was investigated by laser Doppler velocimetry for two different mean residence time‐mixing time ratios. Velocity measurements were obtained for two inlet locations, corresponding to the incoming liquid stream being fed co‐currently or counter‐currently to the flow discharged by the turbine. In all investigated configurations and for all operating conditions, it was found that the flow disruption caused by the incoming liquid stream was observable mainly in the first vessel quarter, which followed the feed‐tube plane. From comparison of the velocities encountered in the various planes in the continuous‐flow reactor to the velocities of the batch reactor, it was also concluded that it may be possible to intensify the usage of the turbine‐stirred vessel by decreasing the characteristic times ratio, without considerable flow by‐pass and/or short‐circuiting problems.     

一种基于并联机构的航天器姿态模拟装置的设计开发

航天器发射升空前进行地面测试和试验是航天器研制过程中的重要环节。文中针对一种基于并联机构的姿态模拟装置的设计开发,从位置分析、速度分析和虚拟样机的建造和仿真分析等方面对3UPS-PU并联机构进行研究,完成姿态模拟装置的设计,为航天器装配、试验和测试设备的设计提供一种新的思路。     

Effects of laser heat treatment on the fracture morphologies of X80 pipeline steel welded joints by stress corrosion

The surfaces of X80 pipeline steel welded joints were processed with a CO2 laser, and the effects of laser heat treatment （LHT） on H2S stress corrosion in the National Association of Corrosion Engineers （NACE） solution were analyzed by a slow strain rate test. The fracture morphologies and chemical components of corrosive products before and after LHT were analyzed by scanning electron microscopy and energy-dispersive spectroscopy, respectively, and the mechanism of LHT on stress corrosion cracking was discussed. Results showed that the fracture for welded joints was brittle in its original state, while it was transformed to a ductile fracture after LHT. The tendencies of hydrogen-induced corrosion were reduced, and the stress corrosion sensitivity index decreased from 35.2% to 25.3%, indicating that the stress corrosion resistance of X80 pipeline steel welded joints has been improved by LHT.