Influence of the deposition atmosphere on the characteristics of Pd–Mg thin films prepared by pulsed laser deposition

Bilayered palladium (30 nm thick)–magnesium (350 nm thick) thin films were prepared using the pulsed laser deposition technique in the presence of various background gases (Ar, He and a mixture He + H₂) under different partial pressures (47 and 27 Pa). According to the deposition atmosphere, the Pd/Mg interface shows either a sharp or an extended transition. The electrochemical hydriding properties and the mechanical stability upon cycling of the Pd/Mg film are greatly improved when an extended «intermixing» zone between the Pd and Mg layers is present. The Pd–Mg films prepared under pure helium fulfill these conditions.     

LASER CLADDED TiCN COATINGS ON THE SURFACE OF TTTANIUM

Laser cladded coatings of TiCN were produced on the surface of titanium. To obtain the optimal techniques, several conditions were tested by varying the laser scanning rate. The choice of shielding gas was also studied. The cladded coatings were then evaluated from the surface mechanics point of view based on their microhardness. The microstructure of some interesting samples was investigated by optical micrographs （OM）. The results showed that under the condition of fixed pulse frequency and pulse width, the laser scanning rate and the shielding gas are the main factors influencing the components of coatings. TiCN coatings were decompounded and oxidized during the cladding process in the condition of no shielding gas of N2. X-ray diffraction results indicated that the composite coatings composed of TiCN, TiC, Ti2N, and TiO2 were produced using appropriate techniques. The results indicated that the best condition in terms of the surface microhardness is obtained when the scanning rate is 1.5mm/s, the pulse frequency is 15Hz, the pulse width is 3.0ms, and N2 is chosen as the shielding gas. The microhardness of the composite coatings is about 1331kg · mm^-2, which is about 4 times that of the substrate. The optical micrographs indicated that the cladding zone is made up of TiCN, TiO2 and some interdendritic Ti, but the diffusion zone mainly consists of the dendrites phase, and the cladded depth is about 80μm, which is more than 2 times that of the laser nitrided sample. There were no microcracks or air bubbles in the cladded sample, which was cladded using the above optimal techniques.     

一种可用于可调谐环行Ti：Al_2O_3激光器的宽带单向器

本文介绍一种宽带单向器的原理及设计。选用ＴＧＧ作磁旋光介质，旋光石英晶片作补偿片，所设计的色散补偿型宽带单向器预计可在７００～１０００ｎｍ波长范围内实现环行激光腔中的单向行波运行；将其应用在可调谐环行Ｔｉ：Ａｌ２Ｏ３激光器中，获得了良好的实验结果。     

SiGe: An attractive material for post-CMOS processing of MEMS

This work gives an overview of the different developments for silicon germanium (Si_1−xGe_x) from a MEMS post-processing perspective. First, the maximum processing temperature that does not introduce any damage or degradation into the standard characteristics of the CMOS driving electronics is specified. Then, the optimal type of silicon and germanium gas sources and deposition technique that results in an economical process are identified. Next, the selection criteria for a low thermal budget doping method and doping species are discussed. Finally, the advantage and disadvantage for the different approaches implemented for enhancing the physical properties of poly Si_1−xGe_x at a CMOS backend compatible temperature are highlighted. It is shown that the optimal method depends on the application requirements and the CMOS technology used for realizing the driving electronics.     

堆底熔穿事故的场外后果及其对策

在压水堆核电站应急计划和应急响应中，堆底熔穿事故占有重要位置。本文用法国核电厂事故源项Ｓ３（对应于堆底熔穿事故）计算了在典型气象条件下的场外放射学的后果，根据一般防护决策原则和我国颁布的干预水平，提出了保护公众的应急防护措施的建议。     

熔体塔式造粒法生产尿基复混肥

化肥企业生产尿基复混肥对于农业科学施肥、提高肥料利用率、避免环境污染及促进企业产品结构调整都具有十分重要的意义。熔体塔式造粒法生产尿基复混肥较之其它方法优越性更为显著,笔者简要介绍该法的生产机理、工艺流程、技术特点、国内现状及产品市场前景等方面的一些情况。     

New catalyst systems for the polymerization of acetylene

The catalytic activities of WCI₆Ph₄Sn, MoCl₅Ph₄Sn and tetrabenzyltitanium were examined in the polymerization of acetylene. The structure, morphology and electrical conductivity of the doped and non doped polyacetylene were also studied.     

玻璃纤维毡增强热塑性复合片材的研制和应用

本文简要介绍了玻璃纤维毡增强聚丙烯片材的研制，性能和应用。     

PET熔体输送系统中熔体温度自动控制方案

在热媒温度控制系统中以熔体温度作为主参数,组成串极调节系统。投入运行后,熔体温度稳定,调节阀动作平稳,效果良好。     

PVC发泡制品用助剂--优泡剂

分析了PVC发泡制品成型加工时存在的缺陷,说明了添加优泡剂可弥补PVC发泡制品的缺陷,提高泡孔质量,介绍了优泡剂的品种和使用场合及使用量。