超低功耗的锂电池管理系统设计

为了满足某微功耗仪表的应用,提高安全性能,提出了一种超低功耗锂电池管理系统的设计方案。该方案采用双向高端微电流检测电路,结合开路电压和电荷积分算法实现电量检测。采用纽扣电池代替DC/DC降压电路最大程度降低功耗。系统实现了基本保护、剩余电量检测、故障记录等功能。该锂电池管理系统在仪表上进行验证,结果表明具有良好的稳定性和可靠性,平均工作电流仅145μA。     

商业化的锂离子电池石墨负极材料的研究进展

综述了锂离子电池石墨负极材料的研究进展,对MCMB、天然石墨与人造石墨、炭纤维为代表的石墨负极材料目前的研究和应用现状进行了详细的论述,并对石墨类炭负极的发展作了展望。     

新的氨化-还原试剂--二烷基胺硼氢化锂(LAB)

介绍了一种新的氨化-还原试剂———二烷基胺硼氢化锂,讨论了它在卤代苯腈中的应用,其结果为o 卤代苄腈在与通用的新氨化-还原试剂反应得到相应的氨基苄胺。     

Studies of structure and cycleability of LiMn2O4 and LiNd0.01Mn1.99O4 as cathode for Li-ion batteries

Lithium manganese oxides LiMn₂O₄ and rare earth elements doped LiNd_0.01Mn_1.99O₄ were synthesized by microwave method. The structure and the electrochemical performances of the samples were characterized. XRD data shows both samples exhibit the same pure spinel phase. But due to the introduction of Nd³⁺ ion into the unit cell, the lattice parameter of the Nd-doped spinel was larger than that of the undoped one. The two samples had a similar morphology including small particle size and homogeneous particle distribution as tested by SEM. The cyclic voltammmetry and constant-current charge-discharge tested that Nd-doped spinel displayed a better reversibility and cycleability.     

Preparation of rechargeable lithium batteries with poly(methyl methacrylate) based gel polymer electrolyte by <Emphasis Type="Italic">in situ</Emphasis>γ-ray irradiation-induced polymerization

An admixture of commercial liquid electrolyte (LB302, 1 M solution of LiPF₆ in 1:1 EC/DEC) and methyl methacrylate (MMA) was enclosed in CR2032 cells. The assembled cells were then -ray-irradiated using configurations of half cells and full cells. Through this in situ irradiation polymerization process, we obtained rechargeable lithium ion cells with poly(methyl methacrylate) (PMMA) based gel polymer electrolytes (GPE). Galvanostatic cycling, AC impedance spectroscopy, and cyclic voltammetry were employed to investigate the electrochemical properties of the cells and the gel polymer electrolyte. This PMMA-based gel polymer electrolyte was found to exhibit a high ionic conductivity (at least 10^–3 S cm^–1) at room temperature. Due to a significant increase in the charge transfer resistance between the GPE and the cathode, the cell impedance of a PMMA-based lithium ion cell is greater than that of a liquid-electrolyte-based cell. The discharge capacity of a LiNi_0.8Co_0.2O₂/GPE/graphite is approximately 145 mAh g^–1 for the first cycle and decreases to123 mAh g^–1 after 20 cycles. In addition, a large initial cell impedance (LICI) was observed in the irradiated positive half cell. In this paper, we propose a possible mechanism related to the detachment of the PMMA layer from the lithium electrode. This detachment of the PMMA layer from the lithium electrode has not been explicitly discussed previously.     

Synthesis of highly crystalline spinel LiMn2O4 by a soft chemical route and its electrochemical performance

Highly crystalline spinel LiMn₂O₄ was successfully synthesized by annealing lithiated MnO₂ at a relative low temperature of 600 °C, in which the lithiated MnO₂ was prepared by chemical lithiation of the electrolytic manganese dioxide (EMD) and LiI. The LiI/MnO₂ ratio and the annealing temperature were optimized to obtain the pure phase LiMn₂O₄. With the LiI/MnO₂ molar ratio of 0.75, and annealing temperature of 600 °C, the resulting compounds showed a high initial discharge capacity of 127 mAh g⁻¹ at a current rate of 40 mAh g⁻¹. Moreover, it exhibited excellent cycling and high rate capability, maintaining 90% of its initial capacity after 100 charge-discharge cycles, at a discharge rate of 5 C, it kept more than 85% of the reversible capacity compared with that of 0.1 C.     

Charge/discharge characteristics of sulfur composite cathode materials in rechargeable lithium batteries

The charge and discharge characteristics of lithium batteries with sulfur composite cathodes have been investigated. The sulfur composites showed novel electrochemical characteristics. The analysis of the differential capacity indicated that the discharge process showed two voltage plateaus of 2.10 V and 1.88 V, and the charge process also presented two voltage plateaus of 2.22 V and 2.36 V. The overcharge test showed that the composite cannot be charged over 4.0 V, the voltage always stopped at about 3.9 V during charging, indicating that the composite presented the intrinsic safety for the overcharge of lithium batteries. The overcharge can cause serious safety problem for the conventional Li-ion batteries. The overcharge test also showed that the batteries with sulfur composite were destroyed when the upper cut-off voltage was over 3.6 V. However, the composite presented good reversible capacity after it was deep discharged even to 0 V. It showed stable cycleability and high cycling capacity of 1000 mAh g⁻¹ when cycling between 0.1 V and 3.0 V, indicative of the different characteristic from the conventional oxide cathode materials. The prototype polymer battery with the composite cathode material presented the energy density of 246 Wh kg⁻¹ and 401 Wh L⁻¹.     

Synthesis of Li2Fe0.9Mn0.1SiO4/C composites using glucose as carbon source

Li2Fe0.9Mn0.1SiO4/C composites were synthesized by using glucose as carbon source. The samples were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM) and electrochemical measurements. All Li2Fe0.9Mn0.1SiO4/C composites are of the similar crystal structure. With increasing the carbon content in the range of 5%-20% (mass fraction), the diffraction peaks in XRD patterns broaden and the particle sizes and the tap density of samples decrease. The Li2Fe0.9Mn0.1SiO4/C composites with carbon content of 14.12% show excellent the capacity retention remains 92.2% after 30 cycles.     

锂离子电池用磷腈类聚合物电解质的制备与性能

采用六氯环三磷腈高温开环聚合方法制备了聚二氯磷腈,然后采用醇钠法,取代聚二氯磷腈的氯,制备了聚二（二乙二醇单甲醚）磷腈（MEEP）,探索出了较佳的合成工艺,采用FT-IR、31P-NMR、13C-NMR、质谱对其进行了结构表征和分析。结果表明,所制备的磷腈聚合物确实为MEEP。采用自制的MEEP,与三氟甲基磺酸锂（LiCF3SO3）盐进行复配,制备了锂离子电池用聚合物固体电解质,对其热稳定性、导电性进行了测试,其开始分解温度在200℃以上,室温电导率达到了1.187×10-4S/cm（25℃）,具有较佳的导电性和热稳定性,可用于锂离子电池的电解质。     

Mg2+掺杂的LiFePO4材料的共沉淀合成与表征

提出了一种采用共沉淀法合成镁掺杂的锂离子正极材料LiFePO4的新方法,研究了合成条件,采用XRD,SEM,循环伏安测定,电化学阻抗谱分析,以及充放电测试对合成的材料作了表征分析．结果表明,采用共沉淀合成方法可以获得性能良好的LiFePO4;Mg^2＋掺杂对LiFePO4结构没有产生明显的影响,但掺杂量的大小对LiFePO4的放电性能有较大影响．